Doc #97029
DATA DELAY DEVICES, INC.
1
2/7/97
3 Mt. Prospect Ave. Clifton, NJ 07013
FEATURES
PACKAGES
? 5 taps of equal delay increment ? Delays to 200ns ? Low profile
? Epoxy encapsulated
? Meets or exceeds MIL-D-23859C
FUNCTIONAL DESCRIPTION
The 1516-series device is a fixed, single-input, five-output, passive delay line. The signal input (IN) is
reproduced at the outputs (T1-T5) in equal increments.The delay from IN to T5 (T D ) and the characteristic impedance of the line (Z) are determined by the dash number. The rise time (T R ) of the line is 30% of T D , and the 3dB bandwidth is given by 1.05 / T D . The device is available in a 8-pin DIP (1516) or a 8-pin SMD (1516S),and a wide range of pinouts may be specified.
Part numbers are constructed according to the scheme shown at right. For example, 1516C-101-500B is a 290mil DIP, 100ns, 50? delay line with pinout code B.Similarly, 1516SB-151-501 is a 240 mil SMD, 150ns,500? delay line with standard pinout.
SERIES SPECIFICATIONS
? Dielectric breakdown:50 Vdc ? Distortion @ output:10% max.
? Operating temperature:-55°C to +125°C ? Storage temperature:-55°C to +125°C ? Temperature coefficient:
100 PPM/°C
PINOUT CODES
CODE
IN T1T2T3T4T5GND STD 2345671,8A 1234675,8B 1736458C 7263541,8D
1
2
7
3
6
4
5,8
MOUNTING HEIGHT CODES
CODE HEIGHT (MAX)
DIP SMD A 0.187Yes No B 0.240Yes Yes C
0.290
Yes
Yes
Note:
Codes A and B are not available for all values of T D
Contact technical staff for details
devices, inc.
3IN Signal Input T1-T5Tap Outputs GND Ground
Note:Standard pinout shown
Other pinouts available
8765
1234
GND IN T1T2
GND T5T4T3
DELAY TIME
Expressed in nanoseconds (ns)
First two digits are significant figures Last digit specifies # of zeros to follow
IMPEDANCE
Expressed in nanoseconds (ns)
First two digits are significant figures Last digit specifies # of zeros to follow
PINOUT CODE
See Table
Omit for STD pinout
MOUNTING HEIGHT CODE
See Table PART NUMBER CONSTRUCTION
1516(S)m - xxx - zzz p
DELAY SPECIFICATIONS
T D T I T R ATTENUATION (%) TYPICAL
(ns)(ns)(ns)Z=50?Z=100?Z=200?Z=300?Z=500?
5 1.0 3.0N/A 5N/A N/A N/A 10 2.0 4.0355N/A N/A 15 3.0 5.0355N/A N/A 20 4.0 6.03555N/A 25 5.07.03555730 6.010.035557408.013.0355575010.015.0355776012.020.0356787515.025.0356788016.026.0456*******.030.0456*******.032.0456*******.040.0456*******.050.0N/A 58101018036.060.0N/A 781010200
50.0
70.0
N/A
8101212
Notes:T I represents nominal tap-to-tap delay increment
Tolerance on T D = ±5% or ±2ns, whichever is greater Tolerance on T I = ±5% or ±1ns, whichever is greater “N/A” indicates that delay is not available at this Z
?1997 Data Delay Devices
1516
Doc #97029
DATA DELAY DEVICES, INC.
2
2/7/97
Tel: 973-773-2299 Fax: 973-773-9672 https://www.wendangku.net/doc/043872711.html,
FUNCTIONAL DIAGRAM
GND
IN T5T1T2T3
T4
GND
PACKAGE DIMENSIONS
1516-xx (DIP)
1
2
3
4
5
67
8
each .100±.010Non-Accumulative
Lead Material:
Nickel-Iron alloy 42TIN PLATE
1516S-xx (Gull-Wing)
.110
.010 TYP.
TYP.
1516
Doc #97029
DATA DELAY DEVICES, INC.
3
2/7/97
3 Mt. Prospect Ave. Clifton, NJ 07013
PASSIVE DELAY LINE TEST SPECIFICATIONS
TEST CONDITIONS
INPUT:
OUTPUT:Ambient Temperature:25o
C ± 3o
C
R load :10M ?Input Pulse:
High = 3.0V typical C load :
10pf
Low = 0.0V typical
Threshold:
50% (Rising & Falling)
Source Impedance:50? Max.Rise/Fall Time: 3.0 ns Max. (measured
at 10% and 90% levels)
Pulse Width (T D <= 75ns):PW IN = 100ns Period (T D <= 75ns):PER IN = 1000ns Pulse Width (T D > 75ns):PW IN = 2 x T D Period (T D > 75ns):PER IN = 10 x T D NOTE:The above conditions are for test only and do not in any way restrict the operation of the device.
Timing Diagram For Testing
T RISE
T FALL
PER IN
PW IN
T RISE
T FALL
10%
10%
50%50%90%90%50%50%V IH
V IL
V OH
V OL
INPUT SIGNAL
OUTPUT SIGNAL
T RISE
T FALL
10%
10%
90%90%IN
T1OUT
TRIG
IN TRIG
Test Setup
DEVICE UNDER TEST (DUT)
OSCILLOSCOPE
PULSE GENERATOR
50 ?
R OUT
R IN
R IN = R OUT = Z LINE
T2T3T4T5