odsl96-5000mm
Leuze electronic GmbH + Co. KG In der Braike 1 D-73277 Owen Tel. +49 (0) 7021 573-0info@leuze.de ? https://www.wendangku.net/doc/018590380.html,
W e r e s e r v e t h e r i g h t t o m a k e c h a n g e s ? o d s _09g b .f m
z Reflection-independent distance information
z Highly insensitive to extraneous light z Analogue current or voltage output
z Measurement range and mode adjustable z Teachable switching output z 2 PNP switching outputs
z Easy alignment through visible red light
250…
5000mm
18 - 30 V
DC
Accessories:
(available separately)
z Mounting systems
z Cable with M12 connector (K-D …)z Configuration software
z
Configuration cable KB-ODS96-1500
Dimensioned drawing
A Indicator diode green
B Indicator diode yellow
C Transmitter
D Receiver
E Optical axis
F Device plug M12x1
G Countersinking for SK nut M5, 4.2mm deep H Parameter plug
I Reference edge for the measurement (cover glass)
Electrical connection
ODS 96Optical laser distance sensors
ODS 96M/V-5... Laser - 10
P a r t N o . 501 09359
ODS 96M/V-5... Laser - 10
0808
Specifications
Optical data
Measurement range 1)1)Luminosity coefficient from 6%…90%, temperature range -20°C …+40°C
250…5000mm Resolution 2)2)Minimum and maximum value depend on measurement distance and configuration of the analogue output 1…20mm Light source laser
Wavelength 660nm (visible red light)
Light spot
divergent, 3x12mm2 at 2000mm Laser warning notice
see remarks
Error limits (relative to measurement distance) 3)
3)In the temperature range of -20°C …+40°C, measurement object ≥50x50mm2; at temperatures <-20°C different error limits apply
Absolute measurement accuracy 1)±2.5% up to 3m/±5% at 3…5m Repeatability 4)
4)Same object, identical environmental conditions, temperature range -20°C …+40°C
±2% up to 3m/±3% at 3…5m b/w detect. thresholds (6…90% rem.)≤2% up to 3m/≤3% at 3…5m
Timing
Measurement time 10…100ms Response time
≤300ms Delay before start-up
≤300ms
Electrical data
Operating voltage U B 18…30VDC (incl. residual ripple)Residual ripple
≤15% of U B Open-circuit current ≤150mA
Switching output
PNP transistor, high-active Signal voltage high/low ≥(U B -2V)/≤2V
Analogue output
voltage 1…10V , R L ≥2k Ω current 4…20mA, R L ≤500Ω
Indicators
teach-in on GND
teach-in on +U B
LED green continuous light ready flashing fault teaching procedure off
no voltage
LED yellow
continuous light object inside teach-in measurement distance
flashing teaching procedure
off
object outside teach-in measurement distance
Mechanical data
Metal housing
Housing diecast zinc Optics cover glass
Weight 380g Connection type M12 connector
Environmental data
Ambient temp. (operation/storage)-40°C ...+40°C/-30°C (70)
Protective circuit 5)5)1=transient protection, 2=polarity reversal protection, 3=short circuit protection for all outputs 1,2,3
VDE safety class 6)6)Rating voltage 250VAC
II, all-insulated Protection class IP 67, IP 69K 7)
7)IP 69K test acc. to DIN 40050 part 9 simulated, high pressure cleaning conditions without the use of additives,acids and bases are not part of the test
Laser class
2 (acc. to EN 60825-1)Standards applied
IEC 60947-5-2
A Area not defined
B Linearity not defined
C Measurement range
D Object present
E No object detected F
Measurement distance
Order guide
Designation
Part No.UL With M12 connector
Current output and PNP switching output ODS 96M/V-5510-42050035216z Voltage output and PNP switching output ODS 96M/V-5480-42150036255z
Current output and 2 PNP switching outputs
ODS 96M/V-5520-42650037963
Tables
Remarks
z Measurement time
depends on the reflectivity of the measurement object and on the measurement mode.
z Teaching procedure:(for ODS 96M/V-5510-420 and ODS 96M/V-5480-421)
Position measured object at desired measurement distance. Connect teach input to +U B for ≥2s. Re-connect teach input to GND, switching output is programmed.
z Approved purpose :
The ODS 96 distance sen-sors are optical electronic sensors for the optical, contactless measurement of distance to objects.
ODS
96