当前位置：文档库 › MB95F108AJWPMC-GE1;中文规格书,Datasheet资料

MB95F108AJWPMC-GE1;中文规格书,Datasheet资料

FUJITSU MICROELECTRONICS

DATA SHEET

This web site includes the "Customer Design Review Supplement" which provides the latest cautions on system development and the minimal requirements to be checked to prevent problems before the system development.

https://www.wendangku.net/doc/1a178018.html,/micom/en-support/

8-bit Proprietary Microcontrollers

CMOS

F 2MC-8FX MB95100AM Series

MB95108AM/F104AMS/F104ANS/F104AJS/F106AMS/F106ANS/F106AJS/

MB95F108AMS/F108ANS/F108AJS/F104AMW/F104ANW/F104AJW/F106AMW/MB95F106ANW/F106AJW/F108AMW/F108ANW/F108AJW/FV100D-103

■DESCRIPTION

The MB95100AM series is general-purpose, single-chip microcontrollers. In addition to a compact instruction set,the microcontrollers contain a variety of peripheral functions. Note : F 2MC is the abbreviation of FUJITSU Flexible Microcontroller.

■FEATURE

? F 2MC-8FX CPU core

Instruction set optimized for controllers ?Multiplication and division instructions ?16-bit arithmetic operations ?Bit test branch instruction

?Bit manipulation instructions etc.? Clock

?Main clock

?Main PLL clock

?Sub clock (for dual clock product)

?Sub PLL clock (for dual clock product)

(Continued)

DS07-12614-5E

MB95100AM Series

(Continued)

? Timer

?8/16-bit compound timer × 2 channels

?16-bit reload timer

?8/16-bit PPG × 2 channels

?16-bit PPG × 2 channels

?Timebase timer

?Watch prescaler (for dual clock product)

? LIN-UART

?Full duplex double buffer

?Clock asynchronous (UART) or clock synchronous (SIO) serial data transfer capable ? UART/SIO

?Full duplex double buffer

?Clock asynchronous (UART) or clock synchronous (SIO) serial data transfer capable ? I2C

Built-in wake-up function

? External interrupt

?Interrupt by edge detection (rising, falling, or both edges can be selected)

?Can be used to recover from low-power consumption (standby) modes.

? 8/10-bit A/D converter

?8-bit or 10-bit resolution can be selected

? Low-power consumption (standby) mode

?Stop mode

?Sleep mode

?Watch mode (for dual clock product)

?Timebase timer mode

? I/O ports :

?The number of maximum ports

? Single clock product : 54 ports

? Dual clock product : 52 ports

?Port configuration

? General-purpose I/O ports (N-ch open drain) : 6 ports

? General-purpose I/O ports (CMOS) : Single clock product : 48 ports

Dual clock product : 46 ports

? Programmable input voltage levels of port

Automotive input level / CMOS input level / hysteresis input level

? Flash memory security function

Protects the content of Flash memory (Flash memory device only)

MB95100AM Series

■MEMORY LINEUP

Flash RAM

MB95F104AMS/F104ANS/F104AJS

16K bytes512 bytes

MB95F104AMW/F104ANW/F104AJW

MB95F106AMS/F106ANS/F106AJS

32K bytes1K byte

MB95F106AMW/F106ANW/F106AJW

MB95F108AMS/F108ANS/F108AJS

60K bytes2K bytes

MB95F108AMW/F108ANW/F108AJW

MB95100AM Series

■PRODUCT LINEUP

(Continued)

Part number

Parameter MB95108AM

MB95F 104AMS/MB95F 106AMS/MB95F 108AMS

MB95F 104ANS/MB95F 106ANS/MB95F 108ANS

MB95F 104AMW/MB95F 106AMW/MB95F 108AMW

MB95F 104ANW/MB95F 106ANW/MB95F 108ANW

MB95F 104AJS/MB95F 106AJS/MB95F 108AJS

MB95F 104AJW/MB95F 106AJW/MB95F 108AJW

Type

MASK ROM product

Flash memory product ROM capacity*160 Kbytes (Max) RAM capacity*1 2 Kbytes (Max)

Reset output

Yes

O p t i o n *2

Clock system Selectable single/dual clock*3 Single clock Dual clock Single clock

Dual clock

Low voltage detection reset Yes/No

Yes No

Yes

Clock supervisor No

Yes

CPU functions

Number of basic instructions : 136Instruction bit length : 8 bits Instruction length : 1 to 3 bytes Data bit length : 1, 8, and 16 bits

Minimum instruction execution time : 61.5 ns (at machine clock frequency 16.25 MHz) Interrupt processing time : 0.6 μs (at machine clock frequency 16.25 MHz) General-pur-pose I/O ports

? Single clock product : 54 ports (N-ch open drain : 6 ports, CMOS : 48 ports) ? Dual clock product : 52 ports (N-ch open drain : 6 ports, CMOS : 46 ports) Programmable input voltage levels of port :

Automotive input level / CMOS input level / hysteresis input level Timebase timer Interrupt cycle : 0.5 ms, 2.1 ms, 8.2 ms, 32.8 ms (at main oscillation clock 4 MHz) Watchdog timer

Reset generated cycle

At main oscillation clock 10 MHz : Min 105 ms At sub oscillation clock 32.768 kHz (for dual clock product) : Min 250 ms Wild register Capable of replacing 3 bytes of ROM data

I 2C

Master/slave sending and receiving

Bus error function and arbitration function Detecting transmitting direction function

Start condition repeated generation and detection functions Built-in wake-up function

UART/SIO

Data transfer capable in UART/SIO

Full duplex double buffer, variable data length (5/6/7/8-bit), built-in baud rate generator NRZ type transfer format, error detected function LSB-first or MSB-first can be selected.

Clock asynchronous (UART) or clock synchronous (SIO) serial data transfer capable

P e r i p h e r a l f u n c t i o n s

MB95100AM Series

(Continued)

Part number

Parameter

MB95108AM

MB95F 104AMS/MB95F 106AMS/MB95F 108AMS MB95F

104ANS/MB95F

106ANS/MB95F

108ANS MB95F 104AMW/MB95F 106AMW/MB95F 108AMW MB95F 104ANW/

MB95F 106ANW/

MB95F 108ANW MB95F 104AJS/MB95F 106AJS/MB95F 108AJS MB95F 104AJW/MB95F 106AJW/MB95F 108AJW

LIN-UART

Dedicated reload timer allowing a wide range of communication speeds to be set.Full duplex double buffer

Clock asynchronous (UART) or clock synchronous (SIO) serial data transfer capa-ble

LIN functions available as the LIN master or LIN slave.8/10-bit A/D converter (12 channels)8-bit or 10-bit resolution can be selected.

16-bit reload timer

Two clock modes and two counter operating modes can be selected. Square wave-form output

Count clock : 7 internal clocks and external clock can be selected.

Counter operating mode : reload mode or one-shot mode can be selected.8/16-bit compound timer (2 channels)Each channel of the timer can be used as “8-bit timer × 2 channels” or “16-bit timer × 1 channel”.

Built-in timer function, PWC function, PWM function, capture function, and square waveform output

Count clock : 7 internal clocks and external clock can be selected 16-bit PPG (2 channels)PWM mode or one-shot mode can be selected. Counter operating clock : 8 selectable clock sources Support for external trigger start

8/16-bit PPG (2 channels)

Each channel of the PPG can be used as “8-bit PPG × 2 channels ” or “16-bit PPG × 1 channel ”.

Counter operating clock : Eight selectable clock sources

Watch counter (for dual clock product)Count clock : 4 selectable clock sources (125 ms, 250 ms, 500 ms, or 1 s)

Counter value can be set from 0 to 63. (Capable of counting for 1 minute when

selecting clock source 1 second and setting counter value to 60)Watch prescaler (for dual clock product) 4 selectable interval times (125 ms, 250 ms, 500 ms, or 1 s) External interrupt (12 channels)Interrupt by edge detection (rising, falling, or both edges can be selected.) Can be used to recover from standby modes.

Flash memory

Supports automatic programming, Embedded Algorithm Write/Erase/Erase-Suspend/Resume commands A flag indicating completion of the algorithm

Number of write/erase cycles (Minimum) : 10000 times Data retention time : 20 years

Erase can be performed on each block

Block protection with external programming voltage

Flash Security Feature for protecting the content of the Flash

(MB95F108AMS/F108ANS/F108AJS/F108AMW/F108ANW/F108AJW only) Standby mode

Sleep, stop, watch (for dual clock product) , and timebase timer

P e r i p h e r a l f u n c t i o n s

MB95100AM Series

(Continued)

*1 : For ROM capacity and RAM capacity, refer to “■ MEMORY LINEUP”.*2 : For details of option, refer to “■ MASK OPTION”.*3 : Specify clock mode when ordering MASK ROM.

Note : Part number of the evaluation product in MB95100AM series is MB95FV100D-103. When using it, the MCU

board MB2146-303A-E is required.

■OSCILLATION STABILIZATION WAIT TIME

The initial value of the main clock oscillation stabilization wait time is fixed to the maximum value. The maximum value is shown as follows.

■PACKAGES AND CORRESPONDING PRODUCTS

: Available : Unavailable

Oscillation stabilization wait time

Remarks

(214-2) /F CH

Approx. 4.10 ms (at main oscillation clock 4 MHz)

MB95108AM

MB95F104AMS/F104ANS/

F104AJS

MB95F106AMS/F106ANS/

F106AJS

MB95F108AMS/F108ANS/

F108AJS

MB95F104AMW/F104ANW/

F104AJW

MB95F106AMW/F106ANW/

F106AJW

MB95F108AMW/F108ANW/

F108AJW

MB95FV100D-103

FPT-64P-M24FPT-64P-M23BGA-224P-M08Part number

Parameter

MB95100AM Series ■DIFFERENCES AMONG PRODUCTS AND NOTES ON SELECTING PRODUCTS

? Notes on Using Evaluation Products

The Evaluation product has not only the functions of the MB95100AM series but also those of other products to support software development for multiple series and models of the F2MC-8FX family. The I/O addresses for peripheral resources not used by the MB95100AM series are therefore access-barred. Read/write access to these access-barred addresses may cause peripheral resources supposed to be unused to operate, resulting in unexpected malfunctions of hardware or software.

Particularly, do not use word access to odd numbered byte address in the prohibited areas (If these access are used, the address may be read or write unexpectedly) .

Also, as the read values of prohibited addresses on the evaluation product are different to the values on the flash memory and MASK ROM products, do not use these values in the program.

The Evaluation product do not support the functions of some bits in single-byte registers. Read/write access to these bits does not cause hardware malfunctions. Since the Evaluation, Flash memory, and MASK ROM products are designed to behave completely the same way in terms of hardware and software.

? Difference of Memory Spaces

If the amount of memory on the Evaluation product is different from that of the Flash memory or MASK ROM product, carefully check the difference in the amount of memory from the model to be actually used when developing software.

For details of memory space, refer to “■ CPU CORE”.

? Current Consumption

The current consumption of Flash memory product is typically greater than for MASK ROM product.

For details of current consumption, refer to “■ ELECTRICAL CHARACTERISTICS”.

? Package

For details of information on each package, refer to “■ PACKAGES AND CORRESPONDING PRODUCTS” and “■ PACKAGE DIMENSIONS”.

? Operating Voltage

The operating voltage are different among the Evaluation, Flash memory, and MASK ROM products.

For details of operating voltage, refer to “■ ELECTRICAL CHARACTERISTICS”.

? Difference between RST and MOD Pins

the MOD pin of the MASK ROM product.

MB95100AM Series

■PIN DESCRIPTION

(Continued)

Pin no.Pin name I/O Circuit type*Function

1AVcc ?A/D converter power supply pin 2AVR ?

A/D converter reference input pin

3PE3/INT13P

General-purpose I/O port.

The pins are shared with the external interrupt input.

4PE2/INT125PE1/INT116PE0/INT10

7P83O

General-purpose I/O port

8P829P8110P8011P71/TI0

General-purpose I/O port.

The pin is shared with 16-bit reload timer ch.0 input. 12P70/TO0General-purpose I/O port.

The pin is shared with 16-bit reload timer ch.0 output. 13MOD B An operating mode designation pin 14X0A Main clock input oscillation pin 15X1Main clock input/output oscillation pin 16Vss ?Power supply pin (GND) 17Vcc ?Power supply pin 18C ?

Capacitor connection pin

19PG2/X1A

H/A

Single clock product is general-purpose port (PG2) .

Dual clock product is sub clock input/output oscillation pin (32 kHz). 20PG1/X0A Single clock product is general-purpose port (PG1) .

Dual clock product is sub clock input oscillation pin (32 kHz). 21RST B’

Reset pin

22P00/INT00C

General-purpose I/O port.

The pins are shared with external interrupt input. Large current port.

23P01/INT0124P02/INT0225P03/INT0326P04/INT0427P05/INT0528P06/INT0629P07/INT0730

P10/UI0

General-purpose I/O port.

The pin is shared with UART/SIO ch.0 data input.

MB95100AM Series

(Continued)

Pin no.Pin name I/O Circuit type*

Function

31P11/UO0H

General-purpose I/O port.

The pin is shared with UART/SIO ch.0 data output. 32P12/UCK0General-purpose I/O port.

The pin is shared with UART/SIO ch.0 clock I/O.

33P13/TRG0/ADTG General-purpose I/O port.

The pin is shared with 16-bit PPG ch.0 trigger input (TRG0) and A/D trigger input (ADTG).

34P14/PPG0General-purpose I/O port.

The pin is shared with 16-bit PPG ch.0 output. 35P20/PPG00H

General-purpose I/O port.

The pins are shared with 8/16-bit PPG ch.0 output.

36P21/PPG0137P22/TO00General-purpose I/O port.

The pins are shared with 8/16-bit compound timer ch.0 output. 38P23/TO0139P24/EC0General-purpose I/O port.

The pin is shared with 8/16-bit compound timer ch.0 clock input.40P50/SCL0

General-purpose I/O port.

The pin is shared with I 2C ch.0 clock I/O. 41P51/SDA0General-purpose I/O port.

The pin is shared with I 2C ch.0 data I/O. 42P52/PPG1

General-purpose I/O port.

The pin is shared with 16-bit PPG ch.1 output. 43P53/TRG1General-purpose I/O port.

The pin is shared with 16-bit PPG ch.1 trigger input. 44P60/PPG10K

General-purpose I/O port.

The pins are shared with 8/16-bit PPG ch.1 output.

45P61/PPG1146P62/TO10General-purpose I/O port.

The pins are shared with 8/16-bit compound timer ch.1 output.

47P63/TO1148P64/EC1General-purpose I/O port.

The pin is shared with 8/16-bit compound timer ch.1 clock input. 49P65/SCK General-purpose I/O port.

The pin is shared with LIN-UART clock I/O. 50P66/SOT General-purpose I/O port.

The pin is shared with LIN-UART data output. 51P67/SIN L General-purpose I/O port.

The pin is shared with LIN-UART data input. 52P43/AN11J General-purpose I/O port.

The pins are shared with A/D converter analog input.

53P42/AN1054P41/AN0955

P40/AN08

分销商库存信息: FUJITSU

MB95F108AJWPMC-GE1