plastite 60-1 fasteners

WEST COAST LOCKWASHER,

16730 East Johnson Drive, P.O. Box 3588 Industry, California 91744 ? https://www.wendangku.net/doc/1c8496182.html, ? Phone (800) 331-3816 ? Fax (626) 369-9805

60-1 FASTENERS

SCREWS FOR PLASTIC AND OTHER LOW DENSITY MATERIALS

MINIMUM

OUT OF RECOMMENDED PILOT HOLE SIZES SOFT, DUCTILE BRITTLE "D"

Plastite trilobular thread rolling screws are designed for high performance fastening in a wide range of thermoplastics.The 60°profile on the Type 60-1 screw penetrates deeply into the work piece,absorbing higher torques without stripping and resisting pullout forces.As threads are the plastic material recovers and fills in around the tri-lobular providing resistance to loosening and assuring a secure assembly.

RECOMMENDED PILOT HOLE SIZES FOR 60-1 PLASTITE SCREWS

SCREW SIZE 2-284-206-198-1610-141/4-105/16-9

"C"

MAX. MIN..092 .086.127 .121.147 .141.185 .179.212 .206.276 .270.345 .335

MINIMUM OUT OF

ROUND .002.002.003.004.004.006.006

"D"

MAX. MIN..089 .083.123 .117.143 .137.179 .173.208 .202.268 .262.335 .325

RECOMMENDED PILOT HOLE SIZES FOR 60-1 PLASTITE SCREWS

This trilobular thread rolling screw also has twin lead,sharper (48°)

threads for minimal displacement of materials and a low driving torque requirement.Cracking of plastic and boss breakage is greatly reduced.This version of the Plastite is recommended where high torques are required.

60-1 PLASTITE SCREW

48-2 PLASTITE SCREW

Note: Plastite ?is a registered trademark of Research Engineering and Manufacturing Incorporated.

Page 14

PLASTITE ?48-2 FASTENERS

SCREWS FOR PLASTIC AND OTHER LOW DENSITY MATERIALS

紧固件中英文对照

最全紧固件中英文对照，外贸必备词典！ 一、紧固件 Fasteners 标准紧固件 Standard Fasteners 非标准紧固件 Nonstandard Fasteners 特殊紧固件 Special Fasteners 汽车紧固件 Automotive Fasteners 铜制紧固件 Brass Fasteners 航天用紧固件 Aerospace Fasteners 精密紧固件 Precision Fasteners 化学紧固件 Chemical Fasteners 摩托车紧固件 Motorcycle Fasteners 不锈钢紧固件 Stainless Steel Fasteners 铁道紧固件 Railway Fasteners 防松紧固件 Self-locking Fasteners 高强度紧固件 High strength Fasteners PEM紧固件 PEM Fasteners 钢结构紧固件 Steel Structural Fasteners 压铆紧固件 Self-Clinching Fasteners

铝制紧固件 Aluminum Fasteners 钛合金紧固件 Titanium Alloy Fasteners 尼龙紧固件 Nylon Fasteners 精制紧固件 Finished Fastener 粗制紧固件 Unfinished Fastener 螺纹紧固件 Threaded Fastener 半精制紧固件 Semi-Finished Fastener 抗剪紧固件 Shear Fastener 抗拉紧固件 Tension Fastener 面板紧固件 Panel Fasteners 二、螺栓 Bolts 六角头螺栓Hexagon Head Bolts 六角法兰面螺栓Hexagon Flange Bolts 轨道螺栓（鱼尾螺丝）Track Bolts 高强度螺栓 High Strength Bolts 地脚螺栓Eyelet Bolts 马车螺栓 Carriage Bolts 护拦螺栓 Guardrail Bots 焊接螺栓 Weld Bolts

Edge joints with dowel type fasteners in cross laminated timber

CIB-W18/40-7-2
INTERNATIONAL COUNCIL FOR RESEARCH AND INNOVATION IN BUILDING AND CONSTRUCTION WORKING COMMISSION W18 - TIMBER STRUCTURES
EDGE JOINTS WITH DOWEL TYPE FASTENERS IN CROSS LAMINATED TIMBER
T Uibel H J Bla?
Universit?t Karlsruhe
Germany
MEETING FORTY BLED SLOVENIA AUGUST 2007

Edge Joints with Dowel Type Fasteners in Cross Laminated Timber
T. Uibel, H.J. Bla? Lehrstuhl für Ingenieurholzbau und Baukonstruktionen Universit?t Karlsruhe, Germany
1
Introduction
During the 39th meeting of CIB-W18 the authors presented proposals for the calculation of the load carrying capacity of joints with dowel type fasteners positioned perpendicular to the plane of cross laminated timber (CLT) [4]. In continuation of the research project [1] the load carrying capacity of edge joints with dowels and screws in CLT was examined. To calculate the load carrying capacity of dowel-type fasteners according to Johansen’s yield theory [2], [3] the yield moment of the fasteners and the embedding strength are needed. The withdrawal strength is necessary to calculate the load carrying capacity of axially loaded screws. In addition, the withdrawal strength is important for estimating the rope effect of laterally loaded connections. In the narrow sides of CLT the fasteners can be positioned parallel to the grain direction. The embedment strength and the withdrawal strength are also influenced by gaps and grooves.
plane side
plane side
narrow side
Fig. 1: Opened connection with dowels in cross laminated timber 1

plastite 60-1 fasteners

WEST COAST LOCKWASHER, 16730 East Johnson Drive, P.O. Box 3588 Industry, California 91744 ? https://www.wendangku.net/doc/1c8496182.html, ? Phone (800) 331-3816 ? Fax (626) 369-9805 60-1 FASTENERS SCREWS FOR PLASTIC AND OTHER LOW DENSITY MATERIALS MINIMUM OUT OF RECOMMENDED PILOT HOLE SIZES SOFT, DUCTILE BRITTLE "D" Plastite trilobular thread rolling screws are designed for high performance fastening in a wide range of thermoplastics.The 60°profile on the Type 60-1 screw penetrates deeply into the work piece,absorbing higher torques without stripping and resisting pullout forces.As threads are the plastic material recovers and fills in around the tri-lobular providing resistance to loosening and assuring a secure assembly. RECOMMENDED PILOT HOLE SIZES FOR 60-1 PLASTITE SCREWS SCREW SIZE 2-284-206-198-1610-141/4-105/16-9 "C" MAX. MIN..092 .086.127 .121.147 .141.185 .179.212 .206.276 .270.345 .335 MINIMUM OUT OF ROUND .002.002.003.004.004.006.006 "D" MAX. MIN..089 .083.123 .117.143 .137.179 .173.208 .202.268 .262.335 .325 RECOMMENDED PILOT HOLE SIZES FOR 60-1 PLASTITE SCREWS This trilobular thread rolling screw also has twin lead,sharper (48°) threads for minimal displacement of materials and a low driving torque requirement.Cracking of plastic and boss breakage is greatly reduced.This version of the Plastite is recommended where high torques are required. 60-1 PLASTITE SCREW 48-2 PLASTITE SCREW Note: Plastite ?is a registered trademark of Research Engineering and Manufacturing Incorporated. Page 14 PLASTITE ?48-2 FASTENERS SCREWS FOR PLASTIC AND OTHER LOW DENSITY MATERIALS

Lesson 3 Fasteners and Springs

Lesson 2 Fasteners and Springs Words and Expressons disassembly [,d?s?'sembl?] n. 拆卸；分解 assembly [?'sembl?] n. 装配；集会，集合; 立法机构；议会 component disassembly 部件拆分; 组件分解 assembly drawing [机] 装配图 assembly line 装配线；流水作业线 general assembly 联合国大会 assembly language n. 汇编语言 assembly process 装配过程；汇编过程 national assembly 国民大会 modular ['m?djul?] adj. 模块化的；模数的；有标准组件的 modular design 模块化设计；标准设计 modular structure 模块结构 modular system 模块化系统 bolt [b?ult] n. 螺栓，螺钉；闪电（狗），雷电；门闩；弩箭 nuts and bolts 具体细节，基本要素 high strength bolt 高强度螺栓；高强螺栓 screw [skru:] vt. 旋，拧；压榨；强迫n. 螺旋；螺钉 screw pump 螺旋泵，螺杆泵 screw thread n. 螺纹 ball screw 滚珠螺杆；滚珠丝杆 螺钉和螺栓的区别： 螺栓与螺钉的主要区别是螺钉是将螺纹直接拧入被连接件之一的螺纹孔中，不需使用螺母；而螺栓的螺纹并不往被连接件上拧，而是通过与螺母配合将被连接件夹紧 rivet ['r?v?t] n. 铆钉vt. 铆接；固定；（把目光、注意力等）集中于rivet machine 制铆钉机；铆钉机；拉钉机 rivet joint 铆钉接合 nuisance ['nju?s(?)ns] n. 讨厌的人；损害；麻烦事；讨厌的东西public nuisance n. 妨害公众安宁；妨害公众利益的人或事物 noise nuisance 噪声危害 spring：n. 春天；弹簧；泉水；活力；跳跃 spring festival ['fest?v(?)l] 春节（中国农历正月初一）

Lesson 7 Fasteners and Springs

Lesson 7 Fasteners and Springs Fasteners are devices which permit one part to be joined to a second part and, hence, they are involved in almost all designs. The acceptability of any product depends not only on the selected components, but also on the means by which they are fastened together. The principal purposes of fasteners are to provide the following design features: (1)Disassembly for inspection and repair; (2)Modular design where a product consists of a number of subassemblies. Modular design aids manufacturing as well as transportation. There are three main classifications of fasteners, which are described as follows: (1)Removable. This type permits the parts to be readily disconnected without damaging the fastener. An example is the ordinary nut-and-bolt fastener. (2)Semi permanent. For this type, the parts can be disconnected, but some damage usuassy occurs to the fastener. One such example is a cotter pin. (3)Permanent. When this type of fastener is used, it is intended that the parts will never be disassembled. Examples are riveted and welded joints. The following factors should be taken into account when selecting fasteners for a fiven application: (1)Primary function; (2)Appearance; (3) A large number of small size fasteners versus a small number of large size fasteners(an example id bolts); (4)Operating conditions such as vibration, loads and temperature; (5)Frequency of disassembly; (6)Adjustability in the location of parts; (7)Types of materials to be joined; (8)Consequences of failure or loosening of the fastener. The importance of fasteners can be realized when referring to any complex product. In the case of the automobile, there are literally thousands of parts which are fastened together to produce the total product. The failure or loosening of a single fastener could result in a simple nu9isance such as a door rattle or in a serious situation such as a wheel coming off. Such possibilities must be taken into account in the selection of the type of fastener for the specific application. Springs are mechanical members which are designed to give a relatively large amount of elastic deflecting under the action of an externally applied load. Hooke’Law, which states that deflection is proportional to load, is the basis of behavior of springs. However, some springs are designed to produce a nonlinear relationship between load and deflection. The following is a list of the important purposes and applications of springs: (1)Control of motion in machines. This category represents the majority of spring applications such as operating forces in clutches and brakes. Also, springs are used to maintain contact between two members such ad a cam and its follower. (2)Reduction of transmitted forces as a result of impact or shock loading. Pplications here include automotive suspension system springs and bumper springs. (3)Storage of energy. Applications in this category are found in clocks, movie cameras and

最全紧固件中英文对照

最全緊固件中英文對照，外貿必備詞典！ 一、緊固件 Fasteners 標準緊固件 Standard Fasteners 非標準緊固件 Nonstandard Fasteners 特殊緊固件 Special Fasteners 汽車緊固件 Automotive Fasteners 銅制緊固件 Brass Fasteners 航天用緊固件 Aerospace Fasteners 精密緊固件 Precision Fasteners 化學緊固件 Chemical Fasteners 摩托車緊固件 Motorcycle Fasteners 不銹鋼緊固件 Stainless Steel Fasteners 鐵道緊固件 Railway Fasteners 防松緊固件 Self-locking Fasteners 高強度緊固件 High strength Fasteners PEM緊固件 PEM Fasteners 鋼結構緊固件 Steel Structural Fasteners 壓鉚緊固件 Self-Clinching Fasteners 鋁制緊固件 Aluminum Fasteners 鈦合金緊固件 Titanium Alloy Fasteners 尼龍緊固件 Nylon Fasteners 精制緊固件 Finished Fastener 粗制緊固件 Unfinished Fastener 螺紋緊固件 Threaded Fastener 半精制緊固件 Semi-Finished Fastener 抗剪緊固件 Shear Fastener 抗拉緊固件 Tension Fastener 面板緊固件 Panel Fasteners 二、螺栓 Bolts 六角頭螺栓Hexagon Head Bolts 六角法蘭面螺栓Hexagon Flange Bolts 軌道螺栓（魚尾螺絲）Track Bolts 高強度螺栓 High Strength Bolts 地腳螺栓Eyelet Bolts 馬車螺栓 Carriage Bolts 護攔螺栓 Guardrail Bots 焊接螺栓 Weld Bolts 雙頭螺栓 Double End Bolts 鋼結構連接副 Structural Bolting 內六角螺栓 Hex Socket Bolts 合金鋼螺栓 Alloy Steel Bolts 方頭螺栓 Square Head Bolts/Square Bolts 鉤頭螺栓 Hook Bolts 不銹鋼螺栓 Stainless steel Bolts

DIN_267-30[1].en

ICS 21.060.10 M echanische Verbindungselemente –Technische Lieferbedingungen –Teil 30: M etrische gewinde-furchende Schrauben der Festigkeitsklasse 10.9 In keeping with current practice in standards published by the International Organization for Standardization (ISO), a comma has been used throughout as the decimal marker. Foreword This standard has been prepared by Technical Committee K einschrauben of the Normenausschuss Mechanische Verbindungselemente (Fasteners Standards Committee). It includes additional specifications for case hardened and tempered metric thread rolling screws as in DIN EN ISO 7085. Ref.No.DIN 267-30:2001-02 English price group 05 Sales No.0105 09.01 DEUTSCHE NORM February 2001 267-30 { Continued on pages 2 and 3. ?No part of this translation may be reproduced without the prior permission of DIN Deutsches Institut für Normung e.V., Berlin. Beuth Verlag GmbH , 10772Berlin, Germany,has the exclusive right of sale for German Standards (DIN-Normen). Technical delivery conditions for fasteners Part 30: Metric thread rolling screws of property class 10.9 Translation by DIN-Sprachendienst. In case of doubt, the German-language original should be consulted as the authoritative text. All dimensions are in millimetres. 1Scope This standard specifies requirements for metric thread rolling screws of property class 10.9 designed to produce internal threads with nominal diameters from 2mm to 10mm in materials with a maximum Vickers hardness of 130HV or a maximum Brinell hardness of 124HB, which fit general purpose ISO metric screw threads for use in general applications. 2Normative references This standard incorporates, by dated or undated reference, provisions from other publications. These normative references are cited at the appropriate places in the text, and the titles of the publications are listed below. For dated references, subsequent amendments to or revisions of any of these publications apply to this standard only when incorporated in it by amendment or revision. For undated references, the latest edition of the publication referred to applies.DIN 4000-2Tabular layouts of article characteristics for bolts, screws and fit bolts DIN EN 20898-7Mechanical properties of fasteners –Part 7: Torsional test and minimum torques for bolts and screws with nominal diameters 1mm to 10mm (ISO 898-7:1992) DIN EN ISO 898-1Mechanical properties of fasteners made of carbon steel and alloy steel –Part 1: Bolts, screws and studs (ISO 898-1:1999) DIN EN ISO 4042Fasteners –Electroplated coatings (ISO 4042:1999) DIN EN ISO 10683Fasteners –Non-electrically applied zinc flake coatings (ISO/DIS 10683:1999)*) DIN EN ISO 15330Fasteners –Preloading test for the detection of hydrogen embrittlement –Parallel bearing surface method (ISO 15330:1999) DIN ISO 261ISO general purpose metric screw threads –General plan (ISO 261:1998) *)Currently at draft stage.

第三章 紧固件FASTENERS

第三章紧固件FASTENERS This chapter gives general information about Boeing approved fasteners used on the airplane. 本章节讲解波音批准紧固件常识。 一、Fastener Types紧固件类型 We will emphasize the Solid Rivet, Blind fasteners and Lockbolts,Hex-drive Bolts.

我们将着重了解固杆铆钉，盲紧固件，锁螺栓，Hi-Lok。 1.Solid Rivets固杆铆钉 (1)Most of the fasteners used on this airplane are solid-shank rivets made from specified aluminum alloys. Solid rivets are permanent fasteners that are used where rivets must have sufficient shear strength and where complete hole-filling is important. 飞机上应用的紧固件大部分是铝合金制的固杆铆钉。作为一种永久性紧固件，必须有足够的剪切强度并且能完全塞满铆钉孔。 (2)You can use softer alloy rivets as alternative fasteners for the usual rivets in some locations.A larger number of fasteners or a larger diameter of fastener can be necessary to get the same structural strength. Make sure the material edge margin and fastener spacing are correct when you use softer alloy rivets as alternative fasteners. 在一些位置可以使用软合金的铆钉替代一般铆钉,有必要使用大量的紧固件或者大直径紧固件以达到同等结构强度,并保证紧固件的边距和间距正确。 2.Blind Fasteners盲紧固件 (1)Blind fasteners are fasteners that you can install when you have access to only one side of the structure. 盲紧固件用于只能接近结构一边的情况下。 (2)Although blind fasteners are permitted in some conditions as alternatives to solid fasteners, a larger number of fasteners or a larger

ISO 8991-1986 Designation system for fasteners

ISO 8991:1986(en) Designation system for fasteners Foreword ISO (the International Organization for Standardization) is a worldwide federation of national standards bodies (ISO member bodies). The work of preparing International Standards is normally carried out through ISO technical committees. Each member body interested in a subject for which a technical committee has been established has the right to be represented on that committee. International organizations, governmental and non-governmental, in liaison with ISO, also take part in the work. Draft International Standards adopted by the technical committees are circulated to the member bodies for approval before their acceptance as International Standards by the ISO Council. They are approved in accordance with ISO procedures requiring at least 75 % approval by the member bodies voting. International Standard ISO 8991 was prepared by Technical Committee ISO/TC 2, Fasteners. Users should note that all International Standards undergo revision from time to time and that any reference made herein to any other International Standard implies its latest edition, unless otherwise stated. 1 Scope and field of application This International Standard specifies a system for the designation of fasteners in product standards. 2 System

DIN267-28 2009 中文版

DIN 267-28 2009 Fasteners- Part 28: Steel screws, bolts and studs with locking coating technical delivery conditions English translation of DIN 267-28:2009-09 緊固件- 第28部分：鋼螺釘，螺栓和螺柱鎖定塗層交貨技術條件 英語翻譯的DIN267-28:2009-09 Foreword This standard has been prepared Working Committee NA 067-02-08 AA Schrauben und Muttern mit klebenden und klemmenden Beschichtungen of the Normenausschuss Mechanische Verbindungselemente (Fasteners Standards Committee). 前言 這個標準由工作委員會NA 067-02-08 AA所編制Schrauben und Muttern mit klebenden und klemmenden Beschichtungen of the Normenausschuss Mechanische Verbindungselemente（緊固件標準委員會）。 Amendments This standard differs from DIN 267-28:2004-01 and DIN 267-28 Corrigendum 1:2004-11 as follows: a)corrigendum 1 has been incorporated; b)bright-finished and coated surfaces have been added to the scope of the standard; c)normative references have been revised and updated; d)examples of designation have been added; e)the scope of the standard has been extended to included stainless and high temperature resistant steels; f)restrictions on the corrosion resistance properties have been added; 修訂 本標準不同於DIN 267-28:2004-01和DIN 267-28,更正1:2004-11如下： 1.勘誤表1已被納入 2.成品的明亮度和塗層表面已經在標準中進行了規定; 3.規範性引用檔已被修改和更新 4.已經添加了指定示例; 5.標準的應用範圍已經擴大到包括不銹鋼和耐高溫鋼; 6.抗腐蝕特性的限制也被加入進去