当前位置：文档库 › 单片机-英文参考文献1

单片机-英文参考文献1

Structure and function of the MCS-51 series

Structure and function of the MCS-51 series one-chip computer MCS-51 is a name of a piece of one-chip computer series which Intel Company produces. This company introduced 8 top-grade one-chip computers of MCS-51 series in 1980 after introducing 8 one-chip computers of MCS-48 series in 1976. It belong to a lot of kinds this line of one-chip computer the chips have,such as 8051, 8031, 8751, 80C51BH, 80C31BH,etc., their basic composition, basic performance and instruction system are all the same. 8051 daily representatives- 51 serial one-chip computers .

An one-chip computer system is made up of several following parts: ( 1) One microprocessor of 8 (CPU). ( 2) At slice data memory RAM (128B/256B),it use not depositting not can reading /data that write, such as result not middle of operation, final result and data wanted to show, etc. ( 3) Procedure memory ROM/EPROM (4KB/8KB ), is used to preserve the procedure , some initial data and form in slice. But does not take ROM/EPROM within some one-chip computers, such as 8031 , 8032, 80C ,etc.. ( 4) Four 8 run side by side I/O interface P0 four P3, each mouth can use as introduction , may use as exporting too. ( 5) Two timer / counter, each timer / counter may set up and count in the way, used to count to the external incident, can set up into a timing way too, and can according to count or result of timing realize the control of the computer. ( 6) Five cut off cutting off the control system of the source . ( 7) One all duplexing serial I/O mouth of UART (universal asynchronous receiver/transmitter (UART) ), is it realize one-chip computer or one-chip computer and serial communication of computer to use for. ( 8) Stretch oscillator and clock produce circuit, quartz crystal finely tune electric capacity need outer. Allow oscillation frequency as 12 megahertas now at most. Every the above-mentioned part was joined through the inside data

bus .Among them, CPU is a core of the one-chip computer, it is the control of the computer and command centre, made up of such parts as arithmetic unit and controller , etc.. The arithmetic unit can carry on 8 persons of arithmetic operation and unit ALU of logic operation while including one, the 1 storing device temporarilies of 8, storing device 2 temporarily, 8's accumulation device ACC, register B and procedure state register PSW, etc. Person who accumulate ACC count by 2 input ends entered of checking etc. temporarily as one operation often, come from person who store 1 operation is it is it make operation to go on to count temporarily , operation result and loopback ACC with another one. In addition, ACC is often regarded as the transfer station of data transmission on 8051 inside . The same as general microprocessor, it is the busiest register. Help remembering that agreeing with A expresses in the order. The controller includes the procedure counter , the order is depositted, the order decipher, the oscillator and timing circuit, etc. The procedure counter is made up of counter of 8 for two, amounts to 16. It is a byte address counter of the procedure in fact, the content is the next IA that will carried out in PC. The content which changes it can change the direction that the procedure carries out . Shake the circuit in 8051 one-chip computers, only need outer quartz crystal and frequency to finely tune the electric capacity, its frequency range is its 12MHZ of 1.2MHZ. This pulse signal, as 8051 basic beats of working, namely the minimum unit of time. 8051 is the same as other computers, the work in harmony under the control of the basic beat, just like an orchestra according to the beat play that is commanded.

There are ROM (procedure memory , can only read ) and RAM in 8051 slices (data memory, can is it can write ) two to read, they have each independent memory address space, dispose way to be the same with general memory of computer. Procedure 8051 memory and 8751 slice procedure memory capacity 4KB, address begin from 0000H, used for

preserving the procedure and form constant. Data 8051- 8751 8031 of memory data memory 128B, address false 00FH, use for middle result to deposit operation, the data are stored temporarily and the data are buffered etc.. In RAM of this 128B, there is unit of 32 byteses that can be appointed as the job register, this and general microprocessor is different, 8051 slice RAM and job register rank one formation the same to arrange the location. It is not very the same that the memory of MCS-51 series one-chip computer and general computer disposes the way in addition. General computer for first address space, ROM and RAM can arrange in different space within the range of this address at will, namely the addresses of ROM and RAM, with distributing different address space in a formation. While visiting the memory, corresponding and only an address Memory unit, can ROM, it can be RAM too, and by visiting the order similarly. This kind of memory structure is called the structure of Princeton. 8051 memories are divided into procedure memory space and data memory space on the physics structure, there are four memory spaces in all: The procedure stores in one and data memory space outside data memory and one in procedure memory space and one outside one, the structure forms of this kind of procedure device and data memory separated form data memory, called Harvard structure. But use the angle from users, 8051 memory address space is divided into three kinds: (1) In the slice, arrange blocks of FFFFH , 0000H of location , in unison outside the slice (use 16 addresses). (2) The data memory address space outside one of 64KB, the address is arranged from 0000H 64KB FFFFH (with 16 addresses ) too to the location. (3) Data memory address space of 256B (use 8 addresses). Three above-mentioned memory space addresses overlap, for distinguishing and designing the order symbol of different data transmission in the instruction system of 8051: CPU visit slice, ROM order spend MOVC , visit block RAM order uses MOVX outside the slice, RAM order uses MOV to visit in slice.

8051 one-chip computer have four 8 walk abreast I/O port, call P0, P1, P2 and P3. Each port is 8 accurate two-way mouths, accounts for 32 pins altogether. Every one I/O line can be used as introduction and exported independently. Each port includes a latch (namely special function register ), one exports the driver and a introduction buffer . Make data can latch when outputting, data can buffer when making introduction , but four function of passway these self-same. Expand among the system of memory outside having slice, four port these may serve as accurate two-way mouth of I/O in common use. Expand among the system of memory outside having slice, P2 mouth see high 8 address off; P0 mouth is a two-way bus, send the introduction of 8 low addresses and data / export in timesharing

Output grade , P3 of mouth , P1 of P1 , connect with inside have load resistance of drawing , every one of they can drive 4 Model LS TTL load to output. As while inputting the mouth, any TTL or NMOS circuit can drive P1 of 8051 one-chip computers as P3 mouth in a normal way . Because draw resistance on output grade of them have, can open a way collector too or drain-source resistance is it urge to open a way, do not need to have the resistance of drawing outerly . Mouths are all accurate two-way mouths too. When the conduct is input, must write the corresponding port latch with 1 first . As to 80C51 one-chip computer, port can only offer milliampere of output electric currents, is it output mouth go when urging one ordinary basing of transistor to regard as, should contact a resistance among the port and transistor base , in order to the electricity while restraining the high level from exporting P1~P3 Being restored to the throne is the operation of initializing of an one-chip computer. Its main function is to turn PC into 0000H initially , make the one-chip computer begin to hold the conduct procedure from unit 0000H. Except that the ones that enter the system are initialized normally,as because procedure operate it make mistakes or operate there aren't

mistake, in order to extricate oneself from a predicament , need to be pressed and restored to the throne the key restarting too. It is an input end which is restored to the throne the signal in 8051 China RST pin. Restore to the throne signal high level effective , should sustain 24 shake cycle (namely 2 machine cycles ) the above its effective times. If 6 of frequency of utilization brilliant to shake, restore to the throne signal duration should exceed 4 delicate to finish restoring to the throne and operating. Produce the logic picture of circuit which is restored to the throne the signal:

Restore to the throne the circuit and include two parts outside in the chip entirely. Outside that circuit produce to restore to the throne signal (RST ) hand over to Schmitt's trigger, restore to the throne circuit sample to output , Schmitt of trigger constantly in each S5P2 , machine of cycle in having one more , then just got and restored to the throne and operated the necessary signal insidly. Restore to the throne resistance of circuit generally, electric capacity parameter suitable for 6 brilliant to shake, can is it restore to the throne signal high level duration greater than 2 machine cycles to guarantee. Being restored to the throne in the circuit is simple, its function is very important. Pieces of one-chip computer system could normal running,should first check it can restore to the throne not succeeding. Checking and can pop one's head and monitor the pin with the oscillograph tentatively, push and is restored to the throne the key, the wave form that observes and has enough range is exported (instantaneous), can also through is it restore to the throne circuit group holding value carry on the experiment to change.

At present,MCU to infiltrate all areas of our lives, which is almost difficult to find traces of the field without SCM. Missile navigation equipment, aircraft, all types of instrument control, computer network communications and data transmission, industrial automation, real-time process control and data processing, extensive use of various smart IC

card, civilian luxury car security system, video recorder, camera, fully automatic washing machine control, and program-controlled toys, electronic pet, etc., which are inseparable from the microcontroller. Not to mention the area of robot control, intelligent instruments, medical equipment was. Therefore, the MCU learning, development and application of the large number of computer applications and intelligent control of the scientists, engineers.

SCM is widely used in instruments and meters, household appliances, medical equipment, aerospace, specialized equipment, intelligent management and process control fields, roughly divided into the following several areas:

（1）In the application of Intelligent Instruments

SCM has a small size, low power consumption, controlling function, expansion flexibility, the advantages of miniaturization and ease of use, widely used instrument, combining different types of sensors can be realized Zhuru voltage, power, frequency, humidity, temperature, flow, speed, thickness, angle, length, hardness, elemental, physical pressure measurement. SCM makes use of digital instruments, intelligence, miniaturization, and functionality than electronic or digital circuits more powerful. Such as precision measuring equipment (power meter, oscilloscope, various analytical instrument).

（2）In the industrial control application

With the MCU can constitute a variety of control systems, data acquisition system. Such as factory assembly line of intelligent control,all kinds of alarm systems,and computer networks constitute a secondary control system.

（3）In the Appliance of Household appliances

It can be said that the appliances are basically using SCM, praise from the electric rice, washing machines, refrigerators, air conditioners, color TV, and other audio video equipment, to the electronic weighing

equipment, varied, and omnipresent.

（4）In the field of computer networks and communications applications MCU general with modern communication interface, can be easy with the computer data communication, networking and communications in computer applications between devices had excellent material conditions, are basically all communication equipment to achieve a controlled by MCU from mobile phone, telephone, mini-program-controlled switchboards, building automated communications call system, train radio communication, to the daily work can be seen everywhere in the mobile phones, trunked mobile radio, walkie-talkies, etc..

（5）Microcomputer in the field of medical device applications MCU in the use of medical devices is also quite extensive, such as medical respirator, the various analyzers, monitors, ultrasound diagnostic equipment and hospital beds, etc. call system.

（6）In a variety of major appliances in the modular applications Designed to achieve some special single specific function to be modular in a variety of circuit applications, without requiring the use of personnel to understand its internal structure. If music integrated single chip, seemingly simple function, miniature electronic chip in the net (the principle is different from the tape machine), you need a computer similar to the principle of the complex. Such as: music signal to digital form stored in memory (like ROM), read by the microcontroller, analog music into electrical signals (similar to the sound card).

In large circuits, modular applications that greatly reduce the volume, simplifies the circuit and reduce the damage, error rate, but also easy to replace.

（7）Microcontroller in the application field of automotive equipment SCM in automotive electronics is widely used, such as a vehicle engine controller, CAN bus-based Intelligent Electronic Control Engine,

GPS navigation system, abs anti-lock braking system, brake system, etc.. In addition, the MCU in business, finance, research, education, national defense, aerospace and other fields has a very wide range of applications.

译文

51系列单片机的功能和结构

结构和功能的监控监-51系列之一--计算机芯片监控监-51名是一幅一个电脑晶片,英特尔公司生产系列. 这家公司推出8级一个计算机芯片监控监-51系列之后,于1980年8引入一个计算机芯片监控监,于1976年48系列.。它属于这一类型很多行一个芯片的电脑芯片都如8051、8031、8751、80c51bh,80c31bh等,其基本组成、性能和基本教学制度,都是一样的. 8051每日代表-51系列之一--电脑晶片有一个芯片的计算机系统是由以下几个方面: (1)18微处理器(CPU).

(2)在切片数据存储羊(128B/256B),使用可以不读书不数据写如因经营不中,最后结果要和数据显示等. (3)存储器存储程序/可擦写可编程只读存储器(4KB/8KB),用于保存程序和数据,初步形成片. 但并不存储器/可擦写可编程只读存储器在一些人的电脑芯片,如8031、8032、80c等. （4)经营的84并肩一/四OP0P3接口,每口可以用作介绍,也可以用作输出. (5)两个定时/柜台,每个计时器/柜台可设立和计算的方法,用来计算的外部事件,可以建立成一个时间的方式也可以和根据计算结果或时间实现控制的计算(六)五切断切断源头上控制系统. (七)各一序I/O口UART(异步接收世界/发送(UART)),它是实现一个计算机芯片和一个计算机芯片和通讯系列电脑上使用.

(8)强、时钟振荡器电路生产、水晶石英细调需要外部电容. 为使振动频率目前最. 每上述地区内的数据是通过加入单片机.

其中,CPU的核心是一个电脑芯片,它是计算机和指挥控制中心等部分组成,运算器和控制等. 运算器的可携带8人计算a经营单位的经营逻辑,其中,1temporarilies存储装置8、暂时贮存器2、8的行政协调会累积装置、B、注册登记程序国有PSW等. 累积计200人,行政协调委员会结束对进入检查. 暂时运作往往是来自一店经营者,这是经营下去,使计暂时经营成果和行政协调会. 此外,行政协调会经常被视为转运站,在8051年的数据传输. 一般微处理器一样,是繁忙登记. 帮助大家,表示了赞同的命令. 控制程序包括柜台命令详解,振荡器电路和时间等. 程序相当于16. 这是一个字节地址位的程序,其

实,内容是未来IA将进行PC. 修改的内容,它可以改变方向,进行程序. 在8051电路动摇一个电脑芯片、石英晶体外,只需要相当频繁调整电容,其范围是12mhz的频率1.2mhz. 这一脉冲信号,作为8051年工作的基本节拍,即单位时间内的最低. 8051年是计算机一样,在和谐的工作基本控制打,就像打了一个乐团,按照发挥,指挥. 有存储器(程序存储器,只能读),8051年在羊片(存储数据,是可以写出)二读,他们每个独立存储空间处理,处理方式是一样的,一般的电脑记忆. 8051年和8751年拨款程序存储程序存贮器4kb,从0000h地址,用于保存程序和方式不变. 数据1128b记忆存储数据,00fh假地址,用于存放操作结果中,暂时储存数据和资料等无人。在这种羊128b,有32个单位字节可以出任就业登记,这是与一般不同的微处理器、8051切片和就业登记成立一个级别相同的地点安排. 这是很不相同的记忆监控监-51系列之一--计算机芯片,除了一般电脑的方式处置. 一般电脑先向空间、存储器和RAM,可安排在不同的空间范围内解决这一意愿,即存储器的地址和RAM,地址分配不同的空间形成. 同时来访的记忆,相应的存储器,只有一个地址,可以存储,也可以撞击,并以同样的访问. 这种记忆结构称为普林斯顿结构. 8051记忆分为程序存储空间和数据存储空间的物理结构,有四个存储空间:我们的程序储存在一个数据存储空间之外的数据存储和一个程序存储空间、外一、结构形式的这种程序装置和数据存储与形式的数据存储,称为哈佛结构. 但用用户的角度,讨论8051年的记忆空间分为三类:(1)在时代安排Ffffh座,0000h地点、从容外片(地址用十六). (二)处理数据存储空间之外64kb之一,被安排从地址0000hFfffh64kb(地址16),地点太.

三)处理数据存储空间256b(地址8使用). 上述三个存储空间地址重叠,鉴别设计,象征不同的数据传输的语言系统8051:CPU访问片,以存储器,阻止访问命令Ra用途外用一张旅游片。

8051年1-48芯片计算机与我走/澳港,要求P0、P1、P2和P3. 每个港口8准确双向口,共占32别针. 每一个我/O线可作为引进和输出独立. 每个港口有门闩(即登记特殊功能)、驾驶人、出口实行缓冲. 可当门闩使outputting数据,数据可以缓冲时推出,但这些四个功能

自我同一. 在扩大对外开放具有时代记忆系统,这四个港口可准确双

向口一/O共同使用。在扩大对外开放具有时代记忆系统,高8P2口地

址见客. P0口是一个双向车采用8送数据低地址/出口Timesharing 在8051年的巡回一个计算机芯片和四个一/O港口很巧妙的设计. 熟

悉我/港澳逻辑电路,不仅有利于正确、合理地使用港口、激励周边逻

辑电路设计的一个计算机芯片有所提高. 负载能力和接口港口有一

定的要求,因为产量等,P0和P1口的最终产量、P3口的结构,在不同

的年级,所以,负载能力和接口要求其门南辕北辙相处. 不同于其他

P0口口,其产量即将年级抵抗.。在使用它的嘴巴,用共同使用,是生

产事故等级亮起电路,它是利用NMOS呼吁采取抵制外,应同时输入,

走出失败. 当被用作介绍,应该写"一"的门闩头. 每一个有能驾驶

8P0口输出模式LSTTL载荷. P1口是一个正确的双向口也作为我/海

外广泛使用. P0口不同产量的电路,请联系电力负荷就在有阻力. 事

实上,反抗是两种影响,同时负责操作:1配量负责,定期阻力. 另一种

可能是导致这两个国家与接近,使总经理改变阻值近似零或一组值两

形势十分沉重. 0时,大约是反抗,可以寄以很高的速度; 如果阻值很大,P1口,以妨碍国家引进高. P1口高产量的电力平时,它是利用电流

负载提供庇护,以此抵制和不必回答. 在这里介绍的是用作码头,必

须写1到相应的门闩头也使操作结束。相对约20,000ohms因负载阻力,因为在现场40,000ohms,不会产生影响的数据,输入. P2口的结构

有些类似于P0口有开关. 这是促使口腔类似,但有些不是嘴巴大转

换控制P1. P3口人的多功能港口,嘴也越来越多,P1比"、"3和4缓

冲门". 这两个部分,使她除了精确的双向功能与P1口仅,也可以使

用第二功能每针. "、"一门三转功能实际上它决定将产量数据信号

门闩第二产出功能. 在担任W=1时,问到生产信号; 作为在Q=1时,

信号线可以生产W. 节目时,它是第一个功能,但仍是第二个功能不用

软件P3口提前成立. 这不是硬件是在自动有两个功能outputted当CPU进行社会主义和寻求地点(所在地或字节)访P3口/不是在持久排队,有在硬件门闩促使=1.THE经营原则P3口类似于P1口.

生产级的P3口,P1,P1,内有连接负载阻力划,每个人可以带动4产

出模型LSTTL载荷. 而作为输入口,任何NMOS电路可驱动TTL或P1的8051一个电脑芯片P3口的正常发展. 由于产量等作出抵抗的人,也可以公开方式收藏或流失的根源就是反抗的方式,要求公开,不须具备抵抗绘画. 别人都准确双向口也. 当行为投入,要写出一首相应的港口与门闩. 以80c51一个计算机芯片,只能提供港口毫安的电流电产出,它是生产口去要求一个普通的计算是将晶体管、接触的阻力应该在港口及半导体基地同时为了抑制高电力输出P1~P3级是恢复王位是一个着手运作一个计算机芯片. 其主要功能是将电脑变成0000h开始,使一个开始进行计算机芯片进行程序0000h单位. 除了那些进入正常initialized系统,因为它的程序操作失误或操作失误不多,为了摆脱困境,必须按国家和恢复王位,恢复太重要了. 这是一项投入恢复王位,结束了在8051年中国信息表寄. 恢复王位高有效信号,应保持24震撼周期(机器周期,2)有效时间段. 6如果使用频率前去辉煌,恢复王位信号完成期限不得超过4微妙的王位,恢复营业. 逻辑电路生产情况,恢复王位的信号:

恢复王位的电路两部分组成,包括外部的芯片完全. 外界产生电路恢复王位信号(表)交给史密特的启动,恢复王位样品电路产量,史密特触发不断每一s5p2、机器周期有一次,光有与恢复王位和经营所需insidly信号. 恢复王位抵抗一般线路、电容参数适合6精彩震撼,是否能恢复王位高信号机会大于2周期保证. 正在恢复王位是简单的电路,其作用是非常重要的. 张一电脑芯片系统可正常运作,应先检查一下,才能恢复王位没有成功. 检测可以流行头和监督寄与初步示波器,并把恢复王位的关键,波的形式,并认为有足够的距离输出(瞬间),也就是通过它来恢复电路值进行实现改变。

目前单片机渗透到我们生活的各个领域，几乎很难找到哪个领域没有单片机的踪迹。导弹的导航装置，飞机上各种仪表的控制，计算机的网络通讯与数据传输，工业自动化过程的实时控制和数据处理，广泛使用的各种智能IC卡，民用豪华轿车的安全保障系统，录像机、摄像机、全自动洗衣机的控制，以及程控玩具、电子宠物等等，这些都离不开单片机。更不用说自动控制领域的机器人、智能仪表、医疗

器械了。因此，单片机的学习、开发与应用将造就一批计算机应用与智能化控制的科学家、工程师。

单片机广泛应用于仪器仪表、家用电器、医用设备、航空航天、专用设备的智能化管理及过程控制等领域，大致可分如下几个范畴：（1）在智能仪器仪表上的应用

单片机具有体积小、功耗低、控制功能强、扩展灵活、微型化和使用方便等优点，广泛应用于仪器仪表中，结合不同类型的传感器，可实现诸如电压、功率、频率、湿度、温度、流量、速度、厚度、角度、长度、硬度、元素、压力等物理量的测量。采用单片机控制使得仪器仪表数字化、智能化、微型化，且功能比起采用电子或数字电路更加强大。例如精密的测量设备（功率计，示波器，各种分析仪）。（2）在工业控制中的应用

用单片机可以构成形式多样的控制系统、数据采集系统。例如工厂流水线的智能化管、电梯智能化控制、各种报警系统，与计算机联网构成二级控制系统等。

（3）在家用电器中的应用

可以这样说，现在的家用电器基本上都采用了单片机控制，从电饭褒、洗衣机、电冰箱、空调机、彩电、其他音响视频器材、再到电子秤量设备，五花八门，无所不在。

（4）在计算机网络和通信领域中的应用

现代的单片机普遍具备通信接口，可以很方便地与计算机进行数据通信，为在计算机网络和通信设备间的应用提供了极好的物质条件，现在的通信设备基本上都实现了单片机智能控制，从手机，电话机、小型程控交换机、楼宇自动通信呼叫系统、列车无线通信、再到日常工作中随处可见的移动电话，集群移动通信，无线电对讲机等。（5）单片机在医用设备领域中的应用

单片机在医用设备中的用途亦相当广泛，例如医用呼吸机，各种分析仪，监护仪，超声诊断设备及病床呼叫系统等等。

（6）在各种大型电器中的模块化应用

某些专用单片机设计用于实现特定功能，从而在各种电路中进行模块化应用，而不要求使用人员了解其内部结构。如音乐集成单片机，看似简单的功能，微缩在纯电子芯片中（有别于磁带机的原理），就需要复杂的类似于计算机的原理。如：音乐信号以数字的形式存于存储器中（类似于ROM），由微控制器读出，转化为模拟音乐电信号（类似于声卡）。

在大型电路中，这种模块化应用极大地缩小了体积，简化了电路，降低了损坏、错误率，也方便于更换。

（7）单片机在汽车设备领域中的应用

单片机在汽车电子中的应用非常广泛，例如汽车中的发动机控制器，基于CAN总线的汽车发动机智能电子控制器，GPS导航系统，abs防抱死系统，制动系统等等。

此外，单片机在工商，金融，科研、教育，国防航空航天等领域都有着十分广泛的用途。

单片机英语文献翻译

学校：数理与软件工程学院

专业：应用物理

姓名：郭瑞

学号：200705211

AT89C51单片机外文翻译

AT89C51外文翻译 Description The AT89C51 is a low-power, high-performance CMOS 8-bit microcomputer with 4K bytes of Flash Programmable and Erasable Read Only Memory (PEROM). The device is manufactured using Atmel’s high density nonvolatile memory technology and is compatible with the industry standard MCS-51? instruction-set and pinout. The on-chip Flash allows the program memory to be reprogrammed in-system or by a conventional nonvolatile memory programmer. By combining a versatile 8-bit CPU with Flash on a monolithic chip, the Atmel AT89C51 is a powerful microcomputer which provides a highly flexible and cost effective solution to many embedded control applications. Features ? Compatible with MCS-51? Products ? 4K Bytes of In-System Reprogrammable Flash Memory – Endurance: 1,000 Write/Erase Cycles ? Fully Static Operation: 0 Hz to 24 MHz ? Three-Level Program Memory Lock ? 128 x 8-Bit Internal RAM ? 32 Programmable I/O Lines ? Two 16-Bit Timer/Counters ? Six Interrupt Sources ? Programmable Serial Channel ? Low Power Idle and Power Down Modes The AT89C51 provides the following standard features: 4K bytes of Flash,128 bytes of RAM, 32 I/O lines, two 16-bit timer/counters, a five vector two-level interrupt architecture, a full duplex serial port, on-chip oscillator and clock circuitry. In addition, the AT89C51 is designed with static logic for operation down to zero frequency and supports two software selectable power saving modes. The Idle Mode stops the CPU while allowing the RAM, timer/counters, serial port and interrupt system to continue functioning. The Power-down Mode saves the RAM contents but freezes the oscillator disabling all other chip functions until the next hardware reset.

单片机-英文参考文献1

毕业设计外文翻译附原文

外文翻译专业机械设计制造及其自动化学生姓名刘链柱班级机制111 学号1110101102 指导教师葛友华

外文资料名称： Design and performance evaluation of vacuum cleaners using cyclone technology 外文资料出处：Korean J. Chem. Eng., 23(6), (用外文写) 925-930 (2006) 附件： 1.外文资料翻译译文 2.外文原文

应用旋风技术真空吸尘器的设计和性能介绍吉尔泰金，洪城铱昌，宰瑾李，刘链柱译摘要：旋风型分离器技术用于真空吸尘器 - 轴向进流旋风和切向进气道流旋风有效地收集粉尘和降低压力降已被实验研究。优化设计等因素作为集尘效率，压降，并切成尺寸被粒度对应于分级收集的50％的效率进行了研究。颗粒切成大小降低入口面积，体直径，减小涡取景器直径的旋风。切向入口的双流量气旋具有良好的性能考虑的350毫米汞柱的低压降和为1.5μm的质量中位直径在1米3的流量的截止尺寸。一使用切向入口的双流量旋风吸尘器示出了势是一种有效的方法，用于收集在家庭中产生的粉尘。摘要及关键词：吸尘器; 粉尘; 旋风分离器引言我们这个时代的很大一部分都花在了房子，工作场所，或其他建筑，因此，室内空间应该是既舒适情绪和卫生。但室内空气中含有超过室外空气因气密性的二次污染物，毒物，食品气味。这是通过使用产生在建筑中的新材料和设备。真空吸尘器为代表的家电去除有害物质从地板到地毯所用的商用真空吸尘器房子由纸过滤，预过滤器和排气过滤器通过洁净的空气排放到大气中。虽然真空吸尘器是方便在使用中，吸入压力下降说唱空转成比例地清洗的时间，以及纸过滤器也应定期更换，由于压力下降，气味和细菌通过纸过滤器内的残留粉尘。图1示出了大气气溶胶的粒度分布通常是双峰形，在粗颗粒（>2.0微米）模式为主要的外部来源，如风吹尘，海盐喷雾，火山，从工厂直接排放和车辆废气排放，以及那些在细颗粒模式包括燃烧或光化学反应。表1显示模式，典型的大气航空的直径和质量浓度溶胶被许多研究者测量。精细模式在0.18?0.36 在5.7到25微米尺寸范围微米尺寸范围。质量浓度为2?205微克，可直接在大气气溶胶和 3.85至36.3μg/m3柴油气溶胶。

51单片机毕设参考文献

基于单片机的大棚温湿度控制系统设计发布: 2011-9-1 | 作者: —— | 来源:caiminghao| 查看: 530次| 用户关注：摘要：针对研究蔬菜大棚智能温湿度控制，设计了一种基于计算机自动控制的智能蔬菜大棚温湿度控制系统。详细阐述了该系统的温湿度采集、温湿度显示、控制系统等系统软硬件的设计思想，以DS18B20和HM1500LF作为温湿度传感器，以AT89S52单片机为系统核心，最后利用DELPHI软件进行系统仿真。该研究设计的蔬菜大棚智能温湿度控制系统人机界面良好，操作简单方便，自动化程度高，造价低廉，具有良好的应用前景和推广价值。关键词：温度采摘要：针对研究蔬菜大棚智能温湿度控制，设计了一种基于计算机自动控制的智能蔬菜大棚温湿度控制系统。详细阐述了该系统的温湿度采集、温湿度显示、控制系统等系统软硬件的设计思想，以DS18B20和HM1500LF作为温湿度传感器，以AT89S52单片机为系统核心，最后利用DELPHI软件进行系统仿真。该研究设计的蔬菜大棚智能温湿度控制系统人机界面良好，操作简单方便，自动化程度高，造价低廉，具有良好的应用前景和推广价值。关键词：温度采集；湿度采集；LCD显示；单片机 0 引言植物的生长都是在一定的环境中进行的，在生长过程中受到环境中各种因素的影响，其中影响最大的是温度和湿度。若昼夜的温度和湿度变化很大，其对植物生长极为不利。因此必须对温度和湿度进行监测和控制，使其适合植物的生长，以提高其产量和质量。本系统就是针对大棚内温度、湿度，研究单片机控制的温室大棚自动控制，综合考虑系统的精度、效率以及经济性要求多方面因素之后，设计一种基于计算机自动控制的大棚温湿度控制系统。本系统实现的蔬菜大棚温湿度控制系统的目标功能如下： (1)系统能对大棚环境温湿度进行采集和显示(现场观温、湿度，软件记录)。 (2)能通过上位机端远程设定蔬菜的生长期适宜温湿度。由主控机统一设置系统时间和温度湿度修正值。 (3)当大棚的环境温湿度参数超过设定的上下限值时控制相应的系统启动。 (4)可实时显示当前温度、时间、报警阈值等信息，并可查询各时间段的温湿度情况，并加以控制。 1 系统各组成模块

毕业设计英文翻译

使用高级分析法的钢框架创新设计 1．导言在美国，钢结构设计方法包括允许应力设计法(ASD)，塑性设计法(PD)和荷载阻力系数设计法(LRFD)。在允许应力设计中，应力计算基于一阶弹性分析，而几何非线性影响则隐含在细部设计方程中。在塑性设计中，结构分析中使用的是一阶塑性铰分析。塑性设计使整个结构体系的弹性力重新分配。尽管几何非线性和逐步高产效应并不在塑性设计之中，但它们近似细部设计方程。在荷载和阻力系数设计中，含放大系数的一阶弹性分析或单纯的二阶弹性分析被用于几何非线性分析，而梁柱的极限强度隐藏在互动设计方程。所有三个设计方法需要独立进行检查，包括系数K计算。在下面，对荷载抗力系数设计法的特点进行了简要介绍。结构系统内的内力及稳定性和它的构件是相关的，但目前美国钢结构协会（AISC）的荷载抗力系数规范把这种分开来处理的。在目前的实际应用中，结构体系和它构件的相互影响反映在有效长度这一因素上。这一点在社会科学研究技术备忘录第五录摘录中有描述。尽管结构最大内力和构件最大内力是相互依存的（但不一定共存），应当承认，严格考虑这种相互依存关系，很多结构是不实际的。与此同时，众所周知当遇到复杂框架设计中试图在柱设计时自动弥补整个结构的不稳定（例如通过调整柱的有效长度）是很困难的。因此，社会科学研究委员会建议在实际设计中，这两方面应单独考虑单独构件的稳定性和结构的基础及结构整体稳定性。图28.1就是这种方法的间接分析和设计方法。

在目前的美国钢结构协会荷载抗力系数规范中，分析结构体系的方法是一阶弹性分析或二阶弹性分析。在使用一阶弹性分析时，考虑到二阶效果，一阶力矩都是由B1,B2系数放大。在规范中，所有细部都是从结构体系中独立出来，他们通过细部内力曲线和规范给出的那些隐含二阶效应，非弹性，残余应力和挠度的相互作用设计的。理论解答和实验性数据的拟合曲线得到了柱曲线和梁曲线，同时Kanchanalai发现的所谓“精确”塑性区解决方案的拟合曲线确定了梁柱相互作用方程。为了证明单个细部内力对整个结构体系的影响，使用了有效长度系数，如图28.2所示。有效长度方法为框架结构提供了一个良好的设计。然而，有效长度方法的

步进电机及单片机英文文献及翻译

外文文献： Knowledge of the stepper motor What is a stepper motor： Stepper motor is a kind of electrical pulses into angular displacement of the implementing agency. Popular little lesson: When the driver receives a step pulse signal, it will drive a stepper motor to set the direction of rotation at a fixed angle (and the step angle). You can control the number of pulses to control the angular displacement, so as to achieve accurate positioning purposes; the same time you can control the pulse frequency to control the motor rotation speed and acceleration, to achieve speed control purposes. What kinds of stepper motor sub-： In three stepper motors: permanent magnet (PM), reactive (VR) and hybrid (HB) permanent magnet stepper usually two-phase, torque, and smaller, step angle of 7.5 degrees or the general 15 degrees; reaction step is generally three-phase, can achieve high torque output, step angle of 1.5 degrees is generally, but the noise and vibration are large. 80 countries in Europe and America have been eliminated; hybrid stepper is a mix of permanent magnet and reactive advantages. It consists of two phases and the five-phase: two-phase step angle of 1.8 degrees while the general five-phase step angle of 0.72 degrees generally. The most widely used Stepper Motor. What is to keep the torque (HOLDING TORQUE) How much precision stepper motor? Whether the cumulative： The general accuracy of the stepper motor step angle of 3-5%, and not cumulative.

51单片机英文翻译

Single chip brief introduction The monolithic integrated circuit said that the monolithic micro controller, it is not completes some logical function the chip, but integrates a computer system to a chip on. Summary speaking: A chip has become a computer. Its volume is small, the quality is light, and the price cheap, for the study, the application and the development has provided the convenient condition. At the same time, the study use monolithic integrated circuit is understands the computer principle and the structure best choice. The monolithic integrated circuit interior also uses with the computer function similar module, SCM basic component is a central processing unit (CPU in the computing device and controller), read-only memory (usually expressed as a ROM), read-write memory (also known as Random Access Memory MRAM is usually expressed as a RAM) , input / output port (also divided into parallel port and serial port, expressed as I / O port), and so composed. In fact there is also a clock circuit microcontroller, so that during operation and control of the microcontroller, can rhythmic manner. In addition, there are so-called "break system", the system is a "janitor" role, when the microcontroller control object parameters that need to be intervention to reach a particular state, can after this "janitor" communicated to the CPU, so that CPU priorities of the external events to take appropriate counter-measures. what is different is its these part performance is opposite our home-use computer weak many, but the price is also low, generally does not surpass 10 Yuan then ......Made some control electric appliance one kind with it is not the 'very complex work foot, We use now the completely automatic drum washer, the platoon petti-coat pipe: VCD and so on Inside the electrical appliances may see its form! ......It is mainly takes the control section the core part It is one kind of online -like real-time control computer, online -like is the scene control, needs to have the strong antijamming ability, the low cost, this is also and the off-line type computer (for instance home use PC,) main difference The monolithic integrated circuit is depending on the procedure, and may revise. Realizes the different function through the different procedure, particularly special unique some functions, this is other component needs to take the very big effort to be able to achieve, some are the flowered big strength is also very difficult to achieve. One is not the very complex function, if develops in the 50s with the US 74 series, or the 60s's CD4000 series these pure hardware do decides, the electric circuit certainly arc a big PCB board ! But if, if succeeded in the 70s with the US puts in the market the series monolithic integrated circuit, the result will have the huge difference. Because only the monolithic integrated circuit compiles through you the procedure may realize the high intelligence, high efficiency, as well as redundant reliability The CPU is the key component of a digital computer. Its purpose is to decode instruction received from memory and perform transfers, arithmetic, logic, and control operations with data stored in internal registers, memory, or I/O interface units. Externally, the CPU provides one or more buses for transferring instructions, data, and control information to and from components connected to it. A microcontroller is present in the keyboard and in the monitor in the generic computer; thus these components are also shaded. In such microcontrollers, the CPU may be quite different from those discussed in this chapter. The word lengths may be short, the number of registers small, and the instruction sets limited. Performance, relatively speaking, is poor, but adequate for the task. Most

单片机传感器参考文献

[1] 王青云. 基于单片机的温度测量系统[J] 2010，(05). [2] 彭立，张建洲，王少华. 自适应温度控制系统的研制[J]东北师大学报(自然科学版), 1994,(01) . [3] Jack Shandle. 即将来临的32位浪潮——ARM构架在32位微控制器领域的应用[J]单片机与嵌入式系统应用, 2004,(03) . [4] 刘侃,张永泰,刘洛琨. ARM程序设计优化策略与技术[J]单片机与嵌入式系统应用, 2004,(04) . [5] 何立民．从Cygnal 80C51F看8位单片机发展之路．单片机与嵌入式系统应用[M]，2002年，第5期：P5~8 [6] 夏继强. 单片机实验与实践教程. 北京：北京航空航天大学出版社, 2001 [7] 徐惠民、安德宁．单片微型计算机原理接口与应用．第1版[M]．北京：北京邮电大学出版社，1996 [8] 张媛媛,何怡刚,徐雪松. 基于C8051F020的温湿度控制箱设计[J]国外电子元器件, 2004,(10) . [9] 江孝国,王婉丽,祁双喜. 高精度PID温度控制器[J]电子与自动化, 2000,(05) . [10] 于洋. 高低温试验箱微机自动控制系统的设计[J]工业仪表与自动化装置, 2003,(02) . [11] 沈聿农.传感器及应用技术[M].北京:化学工业出版社,2001. [12] 范晶彦.传感器与检测技术应用[M].北京:机械工业出版社,2005. [13] 王俊峰,孟令启.现代传感器应用技术[M].北京:机械工业出版社,2007. [14] 金发庆.传感器技术与应用[M].北京:机械工业出版社,2006. [15] Goldman JM, Petterson MT, Kopotic RJ, Barker SJ.Masimosignal extraction pulse oximetry[J].J Clin Monit Comput.2000;16(7):7 5-83. [16] D. Tulone. On the feasibility of global time estimation under isolation conditions in wireless sensor networks. [17] 王春晖. 环境试验箱中制冷系统的原理分析及优化概述[J]电子质量, 2003,(12) [18] 李建中. 单片机原理及应用[M]西安电子科技大学出版社,2010.(02) [19] 周航慈.单片机应用程序设计技术[M].北京：北京航空航大大学出版社，2005. [20] 何立民.单片机高级教程[M].北京：北京航空航天大学出版社，2001. [21] 夏继强.单片机实验与实践教程[M].北京：北京航空航天大学出版社, 2001. [22] 徐惠民,安德宁.单片微型计算机原理接口与应用[M]．北京：北京邮电大学出版社，1996. [23] 李广第．单片机基础[M]．北京：北京航空航天大学出版社，1999. [24] 赵晓安. MCS-51单片机原理及应用[M]. 天津：天津大学出版社，2001. [25] 杨清梅,孙建民.传感器与测试技术[M].哈尔滨: 哈尔滨工程大学出版社,2005. [26] 范晶彦.传感器与检测技术应用[M].北京:机械工业出版社,2005. [27] 王俊峰,孟令启.现代传感器应用技术[M].北京:机械工业出版社,2007. [28] 宋文绪,杨帆.自动检测技术[M].北京:高等教育出版社,2000. [1] 王青云. 基于单片机的温度测量系统[J] 2010，(05). [2] 彭立，张建洲，王少华. 自适应温度控制系统的研制[J]东北师大学报(自然科学版), 1994, [3] YD. Tulone. Is it possible to ensure strong data guarantees in highly mobile [4] Jack Shandle. 即将来临的32位浪潮——ARM构架在32位微控制器领域的应用[J]单片机与嵌入式系统应用, 2004,(03) .

毕业设计_英语专业论文外文翻译

1. Introduction America is one of the countries that speak English. Because of the special North American culture, developing history and the social environment, American English has formed its certain unique forms and the meaning. Then it turned into American English that has the special features of the United States. American English which sometimes also called United English or U.S English is the form of the English language that used widely in the United States .As the rapid development of American economy, and its steady position and strong power in the world, American English has become more and more widely used. As in 2005, more than two-thirds of English native speakers use various forms of American English. The philologists of the United States had divided the English of the United States into four major types: “America n creating”; “Old words given the new meaning”; “Words that eliminated by English”;“The phonetic foreign phrases and the languages that are not from the English immigrates”[1]. Compared to the other languages, American English is much simple on word spelling, usage and grammar, and it is one of the reasons that American English is so popular in the world. The thesis analyzes the differences between American English and British English. With the main part, it deals with the development of American English, its peculiarities compared to that of British English, its causes and tendency. 2. Analyses the Differences As we English learners, when we learning English in our junior or senior school, we already came across some words that have different spellings, different pronunciations or different expressions, which can be represented by following contrasted words: spellings in "color" vs. "colour"; pronunciations in "sec-re-ta-ry" vs. "sec-re-try";

单片机_英文参考文献

Structure and function of the MCS-51 series Structure and function of the MCS-51 series one-chip computer MCS-51 is a name of a piece of one-chip computer series which Intel Company produces. This company introduced 8 top-grade one-chip computers of MCS-51 series in 1980 after introducing 8 one-chip computers of MCS-48 series in 1976. It belong to a lot of kinds this line of one-chip computer the chips have,such as 8051, 8031, 8751, 80C51BH, 80C31BH,etc., their basic composition, basic performance and instruction system are all the same. 8051 daily representatives- 51 serial one-chip computers . An one-chip computer system is made up of several following parts: ( 1) One microprocessor of 8 (CPU). ( 2) At slice data memory RAM (128B/256B),it use not depositting not can reading /data that write, such as result not middle of operation, final result and data wanted to show, etc. ( 3) Procedure memory ROM/EPROM (4KB/8KB ), is used to preserve the procedure , some initial data and form in slice. But does not take ROM/EPROM within some one-chip computers, such as 8031 , 8032, 80C ,etc.. ( 4) Four 8 run side by side I/O interface P0 four P3, each mouth can use as introduction , may use as exporting too. ( 5) Two timer / counter, each timer / counter may set up and count in the way, used to count to the external incident, can set up into a timing way too, and can according to count or result of timing realize the control of the computer. ( 6) Five cut off cutting off the control system of the source . ( 7) One all duplexing serial I/O mouth of UART (universal asynchronous receiver/transmitter (UART) ), is it realize one-chip computer or one-chip computer and serial communication of computer to use for. ( 8) Stretch oscillator and clock produce circuit, quartz crystal finely tune electric capacity need outer. Allow oscillation frequency as 12 megahertas now at most. Every the above-mentioned part was joined through the inside data bus .Among them, CPU is a core of the one-chip computer, it is the control of the computer and command centre, made up of such parts as arithmetic unit and controller , etc.. The arithmetic unit can carry on 8 persons of arithmetic operation and unit ALU of logic operation while including one, the 1 storing device temporarilies of 8, storing device 2 temporarily, 8's accumulation

外文翻译--AT89C51单片机的介绍

专业文献翻译题目: AT89C51单片机的介绍姓名: 学院: 专业: 电子信息科学与技术班级: 班学号: 指导教师: 职称: 20 年月日

原文： The Introduction of AT89C51 Description The AT89C51 is a low-power, high-performance CMOS 8-bit microcomputer with 4K bytes of Flash programmable and erasable read only memory (PEROM). The device is manufactured using Atmel’s high-density nonvolatile memory technology and is compatible with the industry-standard MCS-51 instruction set. The on-chip Flash allows the program memory to be reprogrammed in-system or by a conventional nonvolatile memory programmer. By combining a versatile 8-bit CPU with Flash on a monolithic chip, the Atmel AT89C51 is a powerful microcomputer which provides a highly-flexible and cost-effective solution to many embedded control applications. Function characteristic The AT89C51 provides the following standard features: 4K bytes of Flash, 128 bytes of RAM, 32 I/O lines, two 16-bit timer/counters, one 5 vector two-level interrupt architecture, a full duplex serial port, one-chip oscillator and clock circuitry. In addition, the AT89C51 is designed with static logic for operation down to zero frequency and supports two software selectable power saving modes. The Idle Mode stops the CPU while allowing the RAM, timer/counters, serial port and interrupt system to continue functioning. The Power-down Mode saves the RAM contents but freezes the oscillator disabling all other chip functions until the next hardware reset. Pin Description VCC：Supply voltage. GND：Ground.