当前位置：文档库 › 海上钻井英语500句

海上钻井英语500句

海上钻井英语500句 (2)

RIG JACKING-DOWN AND LEG-PULLING OUT降船及拔桩 (2)

MOVING A JACK UP RIG拖航 (3)

JACKING-UP AND PRELOADING升降及压载 (4)

Preperation before making hole钻前准备 (5)

INSTALLATION OF WELL HEAD ASSEMBLY AND PRESSURE TEST井口安装及测试 (7)

BOTTOM HOLE ASSEMBLY井下钻具组合 (8)

OPERATING操作 (9)

TRIPPING 起下钻 (12)

DRILLING 钻井 (14)

CORING 取芯 (16)

HOLE COMPLICATIONS 复杂情况 (17)

DOWN HOLE TROUBLES井下事故 (19)

RUNNING CASING & CEMENTING JOB下套管固井 (21)

SUBSEA EQUIPMENT (23)

COMPLETION，ABANDONMENT AND BOP HANDLING完井，弃井和防喷器处理 (25)

PEPAIR AND MAINTENANCE维修和保养 (28)

SAFETY安全 (30)

TWO TOOLS (34)

海上钻井英语500句

RIG JACKING-DOWN AND LEG-PULLING OUT降船及拔桩

1、E verything’s ready for the move? Has the unloading finished？

准备工作做得怎么样？卸载做完没有？

2、T hey are working to remove the wedges？

现在正在拔桩脚楔块。

3、T he derrick has been skidded to the towing position?

井架已移到适航位置。

4、D rop NO.2 anchor first，and then No.3.

先抛2号锚，后抛3号锚。

5、H ow far are going to lay out the anchor line？

锚缆绳需要放多少？

6、K eep five warps on the drum and lay out the rest.

尽可能放，滚筒上留5圈。

7、W e ’ve got through with the anchors，It’s ready for the boat to connect now.

已抛完锚，可以接拖了。

8、H ave you got emergency equipments ready for the moving？

拖航作业的应急器材准备完了吗？

9、T he variable load is over the allowable limit. We’ll have to unload the surplus cement，

drilling to unload the surplus cement，drilling water and some diesel oil.

可变负荷超过允许量了，应该卸掉多余的水泥、钻井水，以及部分油。

10、Is it O.K to jack the rig down today?

今天可以降船吗？

11、We can’t jack down the rig as the weather is bad.

天气不好，不能降船。

12、The rig jacking-down is under way now.

现在正在降船。

13、The hull bottom is now the water surface.

船体已接触水面。

14、The draft is 3.5 meters.

船体吃水3.5米。

15、Let’s connect the jetting line to jet the legs with 100 psi.

接好冲桩管线，用7公斤/厘米2的压力开始冲桩。

16、The jetting pressure is 100 psi.

冲桩压力7公斤/厘米2的压力。

17、According to the requirements wind speed less than force 3 and wave height less than

1 meter are considered as the optimum weather condition for the jacking down.

按规定，要求风速在3级以下，波高小于1米是最佳的气象条件。

MOVING A JACK UP RIG拖航

18、There will be strong wind，we have to wait on weather.

有强风，必须等候天气好转。

19、The wind speed is 1.5 meters per second and the wave height is less than 0.5 meter today

Great！

今天风速1.5米/秒，浪高小于半米，好极了！

20、Have you worked out the statistical list of variable loads?

平台可变负荷统计表搞好没有？

21、Now the Rig is overloaded to the boat?

现已超载，需要卸载?

22、What materials can be unloaded to the boat?

哪些物品可以卸载到?

23、The surplus barite, bentonite and cement have to trans-fered to the supply boat.

反多余的重晶石，粘土粉和水泥运到拖轮上。

24、The Rig is short of potable water. Tell the boat to come for transferring water to the Rig.

平台生活用水缺乏，让拖轮靠平台打淡水。

25、Where’s the new location? What are the coordinates?

交换机井位在什么地方？经纬度多少？

26、What is our position now?

现在船位在哪里？

27、We have got the Rig position at 17:50 hours;108o35ˊEL (east longitude) and 20o45ˊNL

(north latitude).

17时50分测得船位在：东经108o35ˊ北纬20o45ˊ。

28、Which tug is responsible for handling the anchors?

哪条拖轮负责起抛锚。

29、Drop No.2 and No.3 anchors, right?

抛2号和3号锚，对不对？

30、When do we start jacking the Rig down?

什么时候开始降船。

31、When do we going to start moving?

什么时候开始拖航。

32、The move is supposed to start at eight thirty.

预计8点半起拖。

33、Which one the main tug? The Binhai 281, it has 8,000HP(horse power).

主拖是哪条船？---滨海281，8000马力。

34、what’s the moving speed now?

现在船速多少？

35、About 4 knots.

4节左右。

36、We can jack down the platform only when the wind scale is less than 4 and we have

a smooth sea.

四级风以下，海浪、海流不急时才可降船。

37、The speed has slowed down some because the fog is too thick.

雾太大，航速成降低了些。

38、Which one is the chase boat? how much is the horse power?

护航船是哪一条？有多大马力？

39、It’s the boat binhai 261. She has 6.000HP (horse power).

护航是滨海261船，6000马力。

40、What time will we get to the location.

什么时候我们可以到达井位？

41、According to the present speed the Rig is expected to enter the location area at about 5 oˊ

clock tomorrow morning.

按现在的航速，大约明早5时左右进入井位区。

42、The location buoy is in front over there. .

前面就是井位标。

43、We are ready to drop the anchors.

我们已经做好抛锚准备。

44、Everything is O.K.

一切都正常。

JACKING-UP AND PRELOADING升降及压载

45、What’s the air gap to start preloading?

平台升离水面多少才开始压载？

46、We are not going to preload until the air gap gets to 3 meters.

打算升三米再开始。

47、How much preload water will have to put into the tanks?

压载舱内要加多少压载水？

48、We’ll have to put into 5500 tons of preload water.

要加5500吨。

49、What way are you going to preload?

打算如何压载？

50、We plan to have 3 steps for preloading. Each step will be followed by 30 minutes of

observation. When the preloading finally finishes. There will be 2 hours for observation.

打算分三组压，每组压完观察30分钟，最后压完观察二小时。

51、Do we star preloading right now?

现在开始压载吗？

52、we’ll have to adjust th e brake torque of jacking motors first so that the legs will jack evenly.

先将升降马达的刹车扭矩调匀，这样桩腿升高比较平稳。

53、Can you get it done quickly?

很快能调完吗？

54、It will probably take us one and half hours to adjust the 36 motors.

36个马达大概要1个半小时。

55、When the preloading finishes and no thing abnormal is found, then we’ll be ready to drain the

water off.

压载完了。观察无变化，准备放水。

56、Why has the main engine stopped?

主机为什么停机？

57、They are lowering the raw water tower（deep well pump）now, so only the emergency

generator can be operated.

正在下放海水塔（深井泵），只能开应急发电机。

58、Let me check it ,O.K. penetrate the legs now.

让我看一下，好，可以插桩了。

59、Check the leg penetration. How much penetration do we have?

检查一下插桩情况，看看插下去多少。

60、No.1 and No.2 legs indicate 10 meters and No.3 indicates 12 meters of penetration.

1、2号桩腿插桩10米，3号桩腿插桩12米。

61、Are the main generators back on the line ?

主发电机并联好了吗？

62、O.K., continue to jack up the platform until we have an air gap of 12 meters.

好吧，继续升降船，升到船离水面12米时停。

Preperation before making hole钻前准备

63、Let the roustabouts unload the supply boat 201.

叫甲板班卸201船。

64、Tell the mechanic to check the motor torque.

让机械师检查马达扭矩。

65、Set and fix the upper and lower wedges on the legs.

将桩脚上、下楔块固定好。

66、The drilling crew is responsible to skid the derrick back to the drilling position.

钻井班移动井架到工作位置。

67、Electrician must care of the electric cable – moving whit derrick.

电工注意照管好移动电缆。

68、Speed up. Please!

请快点干！

69、Have you fixed the derrick substructure in position?

井架底座固定好没有？

70、Get all the drilling tools unlashed.

解开所有钻具。

71、Put the ramp back onto the V—door

将坡板吊回到井架大门上。

72、Put the rat—hole scabbard back in place.

安放大鼠洞。

73、Connect the Kelly spinner to the Kelly.

连接动力短节和方钻杆

74、Connect the feeling plate to the drill collars.

用钻铤连接探深板。

75、Have you checked all the equipments?

设备都检查过了吗？

76、We’ve checked them, no problems in running.

检查过了，运转是没有问题了。

77、How much high viscosity mud move you mixed?

高粘度泥浆配备了多少？

78、About 160 cubic meters.

大约160方。

79、Please pick up the 171/2" bit and 36" hole opener to the floor.

请将这个171/2"钻头和36"扩大器吊上钻台。

80、The distance between feeling plate and rotary table is 70 meters.

探测海底到转盘面的深度是72米。

INSTALLATION OF WELL HEAD ASSEMBLY AND PRESSURE TEST井口安装及测

试

81、Cut off the 30"conductor with the conch.

用气焊割掉30"隔水管。

82、Weld on the 30"bottom flange.

焊接30"的底法兰。

83、Hoist and rig up the 30" Tee.

吊装30"三通。

84、Connect the 12"pneumatic valve and the flow line.

连接12"气阀及管线。

85、Hoist and nipple up the 30"diverter.

吊装30"转喷器。

86、Have the 30"diverter pressure-tested with 1000psi.

30"转喷器试压1000磅/英寸2。

87、Rig up the 135/8" BOP stack onto the well head.

将135/8"防喷器组移到井口。

88、This gasket ring can't be used any more. Change to a new one, please.

这个钢圈不能用了，换个新的。

89、Tighten up the well-head guy-lines a bit-more.

井口绷绳绷紧一些。

90、Change the 5" pipe rams to 31/2 " rams.

把这个5"闸板换成31/2"的。

91、Have the HYDRIL [annular preventer] pressure-tested to 5,000psi.

海德里环形防喷器试压5000磅/英寸2。

92、Have the Camron type U BOP pressure-tested with 10,000psi.

卡麦隆U型防喷器试压1000磅/英寸2。

93、Hold each pressure test for 10 minutes.

每次试验稳压10分钟。

94、The pressure –test is O.K.

试压合格。

95、Have each valve of the stand-pipe manifold pressure-tested to 5.000psi.

立管闸门逐个试压5000磅/英寸2。

96、Mud pumps aren’t allowed to be used for the test if the pressure is over 3000psi.

超过000磅/英寸2的不允许直接用泥浆泵试压。

97、Run the wear bushing.

下抗磨补心。

98、Adjust the manifold pressure to 1500psi.

管汇压力调到1500磅/英寸2。

99、Adjust the HYDRIL (annular preventer ) pressure to 900 psi.

环形防喷器压力调到900磅/英寸2。

100、Close the blind ram, please.

请关上防喷器盲板。

101、Open the pipe ram, please.

请打开闸板防喷器。

102、Check the pre-charged pressure of the accumulator.

检查储能器预压。

103、The accumulator pressure of the Koomey Unit is 3,000psi.

库美系统储能压力3000磅/英寸2。

BOTTOM HOLE ASSEMBLY井下钻具组合

104、Get a 121/4" Smith bit ready.

准备一个121/4"史密斯钻头。

105、Don’t forget to put the TOTCO s upport ring in the bit sub (for the deviation survey.

tool.)

别忘了在钻头接头内安放测斜承托环。

106、The thread type of the bit is 6 5/8" regular pin.

钻头的扣型是6 5/8"正规公扣。

107、What’s the make-up torque required for the bit?

钻头上扣力矩要多大？

108、Run in two stands of 9" drill collars.

下两根9"钻铤。

109、Set the make-up torque of 9" DC to 10000 kg-meter.

9"钻铤上扣力矩要调到10000公斤米。

110、The cathead can't give enough torque, so we have to use a snatch block.

猫头力量不够，要挂上滑轮。

111、Connect the 731×630 crossover sub.

接上731×630的配合接头。

112、 A 12 1/4" stabilizer is needed to be connected here.

这个地方要接个12 1/4"的扶正器。

113、This is a 7 3/4" flexible sub.

这是7 3/4"挠性短节。

114、Put the 8" jar on to the flexible sub.

在挠性短节上接上8"震击器。

115、 A function test must be made before the jar is run in the hole.

下震击器时，要做性能试验。

116、Make up 15 joints of 5" HW Drill pipe.

接上15根5"加重钻杆。

117、The DIV (drop in valve) has to be put on top of the bottom two joints of HWDP.

投入式止回阀安在下两根加重钻杆的上面。

118、This is the BHA[bottom hole assembly] log.

这是井下钻具组合的记录本。

119、Make sure you record all outside and inside diameters and lengths in the log 一定要把所有的内外径和长度记好。

120、We need a short drill collar to put here.

这里要接一根短钻铤。

121、Whet is the BHA of this well.

这口井的钻具结构是什么？

122、This is the hole geometry of this well.

这是这口井的井身结构。

123、The thread type of 9"DS is 75/8"Reg[regular].

9"钻铤的扣型是75/8"正规。

OPERATING操作

124、Latch the elevator.

扣吊卡。

125、Unlatch the elevator.

开吊卡。

126、Set the slips around the pipe.

放卡瓦。

127、Pull out the slips.

提卡瓦。

128、Put out the slips.

打大钳。

129、Adjust the crown-o-matic.

调整防碰天车。

130、Put the Kelly into the rat-hole.

方钻杆进鼠洞。

131、Lock the hook pin.

锁紧大钩销子。

132、Pull the cat line.

拉猫头。

133、Unlock the hook.

打开大钩。

134、Operate the brake lever.

扶刹把。

135、Stop the pumps for a flow check.

停泵观察。

136、Make a wiper trip to the 20"casing shoe.

通井到20"套管鞋。

137、Ream down all the tight points.

在所有遇阻点进行划眼。

138、Work the string up and down.

上下活动钻具。

139、Run in the turbine drill.

下涡轮钻具。

140、Reverse out the drill pipe.

反循环清洗钻杆。

141、Make a short trip.

进行短起下钻。

142、Change the cutters of the hole opener.

更换扩大器的牙轮。

143、Slug the pipe.

灌重泥浆。

144、Drill the Kelly down.

钻完方钻杆。

145、Circulate bottoms up for a sample.

循环取样观察。

146、Circulate the hole clean.

循环清洗井眼。

147、Have it greased.

打黄油。

148、Change the Zinc block of cathode Protection.

换阴极保护用的锌棒。

149、Give me a spanner ,please.

请给我拿一个扳手来。

150、We need a 48"pipe wrench.

要一把48"的管钳。

151、Change the chain tong with a bigger one.

换一把大链钳。

152、Strike it with a sledge hammer.

用大锤打。

153、We want a triangle file.

要一把三角锉刀。

154、Tighten up the screw.

紧一下螺丝。

155、Change the jaw assembly on the break out tong.

换钳头。

156、Give me a hand, please.

请帮下忙。

157、Check it with a level.

用水平尺测量一下。

158、Change the chain for the made up cathead.

换一根猫头链子。

159、Put some engine oil on it.

抹点机油。

160、Do you understand?

明白吗？

161、Start the shale shaker.

启动振动筛。

162、Start the desanders and desilters.

开除砂器、除泥器。

163、Shut off the degasser.

关除气器。

164、Pick up the drill pipes on the cat walk [ramp] .

把这几根钻杆拉到坡道上。

165、Connect the rotary hose to the swivel.

接单根要快。

166、Make a faster connection, please !

接水龙带!

167、Lay down the pipe.

甩单根。

168、Set and secure the safety clamps on the drill collars.

给钻铤卡上安全卡瓦。

169、Stab the pipe with the hydraulic arm.

用液压钳扣住钻杆。

170、Don’t dump the mud into the sea.

不要把泥浆排放到海里。

171、Disconnect it with a chain tong.

用链钳卸开。

TRIPPING 起下钻

172、After tripping the string out of the hole.

起完这趟钻，用一个硬一点的休斯钻头更换磨钝的钻头。

173、Connect the junk sub.

接上打捞杯。

174、Check the bit O.D. with a bit gauge.

拿钻头规来量一下钻头外径。

175、When the bit goes through the BOP, slow down, please!

当钻头通过防喷器时，慢一点放。

176、This is the dope for drill pipe thread. It can’t be used for drill collar.

这是钻杆丝扣油，不能用在钻铤丝扣上。

177、2,500 kilos- meter torque is enough for making-up E Grade drill pipe.

E级钻杆上扣力矩用到2500公斤米就可以了。

178、Put a protector on each of 5"drill pipe.

每柱5"钻杆上加一个护箍。

179、Please engage the eddy current brake.

请挂上涡磁刹车。

180、Can we use the power slips?

可以使用气动卡瓦吗

181、Don’t set the slips too low on the pipe!

卡瓦不要卡太低了。

182、No way, the tong angle is too small!

不行，大钳的角度太小了。

183、The hole’s tight. Don’t snub the string.

遇阻了，不要强下。

184、Monitor the returns the trip tank while running in.

下钻时返出泥浆要记录。

185、Stop circulating!

停止循环泥浆。

186、Drop the TOTCO [survey tool].

投“陶特”测斜仪。

187、Break out the Kelly and set it back in the rat-hole.

卸方钻杆并放进鼠洞。

188、Slug the pipe with two cubic meters of mud before pulling out.

起钻前打2方重泥浆。

189、Can we break out the pipe with rotary table?

可用转盘卸扣吗？

190、No! break it out with both sets of tongs.

不行，要用大钳卸扣。

191、Spin it out with the air spinner.

用气动扳手卸扣。

192、Put the pipe wipers on the string.

装上胶皮刮泥器。

193、Tale down the volume while filling the hole.

灌满泥浆，并且要计量。

194、If the string is not very heavy, the top gear can be used to pull it out.

钻具轻可以用高速挡起。

195、Don’t set this stand bac k.

这柱钻杆不要放在钻杆盒上。

196、Lay down this bent drill pipe.

甩掉这根弯钻杆。

197、Make up the lift sub.

接好提升短节。

198、Secure the safety clamp.

上紧安全卡瓦。

199、Rack back the drill-collars onto the finger board.

钻铤靠在指梁上。

200、The bit is nearing the shoe. Slow down the running speed.

快到套管鞋位置了，放慢点速度。

201、This is the under gauged interval.

这是缩径井段。

DRILLING 钻井

202、This is the drilling programmer of CFD18-1-1 WELL.

这是CFD18-1-1井的钻研井设计书。

203、The proposed total depth of this well is 3,900 meters.

这口井的设计井深是3900米。

204、How much WOB [weight on bit] is required?

要加多少钻压？

205、Keep the rotary speed at 120-140 PRM and the flow rate at 3,000LPM[liters per minute].

转速保持120-140转/分，排量3000升/分。

206、The pump pressure is too high！

泵压太高了！

207、Make up the Kelly and circulate bottom’s up.

接方钻杆循环泥浆。

208、Don’t ream the hole too fast.

划眼不要太快。

209、Slow RPM and light WOB are needed in drilling with a new bit at the beginning.

钻头使用初期要慢点转达。

210、Bring the RPM up slowly.

逐步提高转速。

211、Get yourself attentive and careful in the operation.

精心操作。

212、Avoid the brake-slipping or the string –dropping when feeding off while drilling.

在钻进过程中防止溜钻、顿钻。

213、Keep steady pressure on the brake to feed off smoothly.

操作要平稳，做到均匀送钻。

214、Keep an eye on the rotary torque.

注意观察转盘扭矩变化。

215、The penetration rate is getting slower.

钻时变慢了。

216、The bit must have been balled up, mustn’t it?

钻头泥包了，是吗？

217、Has the bit got dull?

是钻头磨秃了吗？

218、The bit has been used too long and is nearly worn out.

钻头已到期后期，快磨坏了。

219、The bit is dull, so we’ll have to pull it out to change to a new one.

钻头不行了，应该起钻换钻头。

220、The pump pressure has increased. One nozzle may be plugged.

泵压升高。可能有个水眼堵了。

221、Stop drilling at 2,965 meters.

钻至2965米，停钻。

222、Get ready to drop a TOTCO (deviation survey ) one the circulation has finished.

循环结束，准备投测。

223、How long is it circulate bottoms up?

需要循环多长时间？

224、Circulate for one and a half hours and then pull the string out at 14:30.

循环一个半钟头，14:30起钻。

225、How long has this bit been used?

这个钻头使用了多长时间？

226、This bit has been used for 25 hours and 15 minutes.

使用了25小时15分钟。

227、This bit has drilled 156 meters of hole.

这个钻头进尺156米。

228、The penetration rate has been 6.18 meters per hour.

机械钻速6.18米/时。

229、This interval of the well is liable to deviate.

这个井段是易斜地层。

230、There should be some changes to the drilling parameters.

要改变一下钻井参数。

231、The dog-leg severity of this well is not very big.

这口井的狗腿变化不大。

232、What was the deviation indication of the last survey?

上次测多少度？

233、The surveyed deviation was 2.5 degrees at 2,900 meters.

在2900米处是2.5度.

234、How much Kelly is out when the bit was at the bottom of the hole?

钻头到底时的方余是多少？

235、Measure the Kelly-down before you are going to trip.

起钻前量一下方入。

236、What will the bit depth be when this joint of pipe goes through the table?

打完这根单根井深是多少？

237、What is the hook load at the time of pulling out?

起钻时悬重是多少？

238、What’s the pick-up weight?

上提重量是多少？

239、What’s the lowering weight?

下放重量是多少？

240、There’s no need to connect this joint.

这个单根不要接了。

241、The well is going to be completed at 3,920 meters.

钻至3920米完钻。

242、What’s the hook load when the HWDP is completely run in the hole.

下完加重钻杆后的悬重是多少

243、High pump pressure and reduction in penetration show wear out of the bit 泵压升高，钻速降低说明钻头磨损。

CORING 取芯

244、The penetration rate is too fast. Stop drilling and do a flow check.

钻速太快，停钻循环观察。

245、The geologist has instructed to stop drilling for coring.

地质师指示：停钻准备取芯。

246、Tell the roustabouts to pick up the 8"×51/4"core barrel to the drill floor.

叫甲板工把那根8"×51/4"的岩芯筒吊到钻台上。

247、What type of core bit is it?

这是什么型号的取芯钻头？

248、We are going to run in a diamond core bit.

我们准备下金钢石取芯钻头。

249、Run in the junk mill and mill on the fish.

下磨鞋将井底落物磨掉。

250、The bit ’s at the bottom now. Let’s drop the ball for coring.

钻头到底了，可以投球取芯。

251、The core footage is 19 meter. Now it’s time to break it off and pull out.

取芯进尺19米了，可以割芯起钻。

252、Slack off a little weight to make sure the core has been broken off.

试放一下，看岩芯断了没有。

253、Don’t brake suddenly while pulling out.

起钻时不要猛刹车。

254、The geologist must be present while taking out the core.

岩芯出筒时，必须有地质人员在场。

255、Put the core in the boxes.

把岩芯装到岩芯盒里。

256、How long is the core?

岩芯长多少？

257、The core recovery is 98%.

岩芯收获率是98%。

258、Are we going to run in core barrel again?

继续下岩芯筒吗？

HOLE COMPLICATIONS 复杂情况

259、The down-hole problems are very complicated.

井下情况很复杂。

260、The string is vibrating badly.

蹩、跳严重。

261、When power supply shut off and the rotary table stopped, the table was still reverse-turning.

停钻后打倒车。

262、We’ve got over pull while ripping out.

起钻遇阻。

263、The hole is tight while running in.

下钻遇阻。

264、The formation is unstable and the wall caving are severe.

地层不稳定，井壁垮塌严重。

265、There are so many return cuttings on the shale shaker.

返出岩屑特别多。

266、The hole’s enlarged ( washout ) .

井眼扩大了（冲刷大了）。

267、The hole’s become under-gauged and mud returns have decreased.

井眼缩小，返出泥浆减少。

268、There are no mud returns while circulating.

循环时没有泥浆返出。

269、The pit level has lowered quickly.

泥浆池液面下降很快。

270、The hole lost returns.

井口不返泥浆（只进不出）。

271、Where’s the thief zone?

漏失层在哪里？

272、Pump the lost circulation materials (LCM) into the hole.

打堵泥浆。

273、Cut down the flow rate.

降低排量。

274、Lower the mud density to cut down the hydrostaics pressure.

降低比重，减少静压（液柱压力）。

275、The returns are unstable.

返出泥浆忽大忽小。

276、The mud is returning with a strong gas smell.

返出泥浆的天然气味大。

277、There’s some trace of oil in the mud.

发现有油花。

278、The pump pressure is fluctuating.

泵压忽高忽低。

279、The drilling break is over 5 meters per minute.

钻速忽然增大，大于5米/分。

280、The pit level has raised and the mud volume gained is 5 cubic meters.

泥浆池液面升高，泥浆量已增加了5方。

281、 A zone of abnormal pressure has been drilled into.

钻入了异常压力层。

282、The hole is kicking!

井涌啦！

283、Sound the general alarm quickly!

快发出井涌警报！

284、Shut in the BOP!

关闭防喷器！

285、The circulation pressure at 30 SPM is 25 kg/cm2(kilos per square centimeters) .

30冲/分的循环压力是25公斤/厘米2。

286、The stand pipe pressure (drill pipe pressure) is 10kg/cm2.

立管压力（钻杆压力）10公斤/厘米2。

287、The casing pressure is 25kg/cm2.

套压25公斤/厘米2。

288、Fill out the kill sheet.

填写压井记录表。

289、Kill the well using the driller’s method.

用司钻法压井。

290、Pump the 1.5 SG mud to kill the well.

注入比重1.5泥浆压井。

291、Call the roustabouts to help weight up mud.

叫甲板上帮助加重泥浆。

292、The hole conditions have been complicated by a combination of lost returns and the kick.

又喷又漏，井下情况很复杂。

293、Reverse the gas out of the hole.

反循环排气。

294、What’s the bottoms up (lag time)？

迟到时间是多少？

295、Stop the pumps to check the level in the hole.

停泵观察井口液面。

296、The well is now stable.

现在井眼已经稳定。

DOWN HOLE TROUBLES井下事故

297、The bit cutters have been lost in the hole.

牙轮落井。

298、Run in the reverse-circulating basket.

下反循环打捞篮。

299、The drill pipe has been twisted off.

钻杆折断。

300、Run in the overshot.

下卡瓦打捞筒。

301、Run in the taper tap to engage the fish.

下公锥打捞落鱼。

302、Connect the safety joint and the fishing jar.

接安全接头和打捞震击器。

303、The drilling tools have backed off in the hole.

钻具脱扣落井。

304、There is a lot of junk in the hole.

井下落物有很多铁块。

305、Run in the junk sub with the mill.

下磨鞋并带打捞杯。

306、The reverse circulating junk basket has to be run in with the 113/4" guide shoe.

反循环打捞篮要带113/4"引鞋。

307、The fish is 235.46 meter long.

落鱼长度235.46米。

308、The fish top is at 2478.34 meter.

鱼顶位置2478.34米。

309、The pipe ’s stuck.

卡钻了。

310、Pull up to 150 tons and slack off to 50 tons.

上提150吨，下放至50吨。

311、The rotary table can’t rotate. There is to much torque.

转盘转不动，扭矩太大了。

312、What kind of sticking is it?

是什么类型卡钻。

313、It’s the differential stacking

是泥饼卡钻。

314、Calculate the free point by tensile test using electric logging equipment.

用电测设备做拉伸试验算卡点。

315、The free point is at 2500 meter.

卡点位置在2500米左右。

316、Pump 10cubic meters of diesel oil and free agents into the hole.

打进柴油和解卡剂10方。

317、Displace mud with 30 SPM each 30 minutes while working the drill string.

每30分钟顶替泥浆30冲，同时活动钻柱。

318、We’ve tried a couple of times to get it free whit the oil but failed what is the next step.

泡油几次都失败了，怎么办

319、Get ready to back it off above the free point.

准备在卡点以上倒扣。

320、Ask the base to send 2500 meters of left-hand drill pipes.

要求基地送反扣钻杆2500米。

321、Run in the explosive with the logging unit to perform a back off.

下电缆进行爆炸解卡。

322、The back –off position is at the end of the last joint of 5" drill pipes.

钻井英语常用词汇及术语缩写.

API(America Petroleum Institute美国石油学会BHA(bottom hole assembelly井底钻具组合BHP(bottom hole pressure井底压力BOP control room远程控制台 BOP(blowout preventer防喷器 BTC(buttress thread connection梯形扣 CP(circulating pressure循环压力 DC(drill collar钻铤 DL(dogleg 狗腿 DLS(dogleg severity狗腿严重度DP(drill pipe钻杆 DST(drill stem test中途测试ECD(equivalent circulating density循环当量密度ECD(equivalent circulating density当量循环密度EF(external flush外平 EMW(equivalent mud weight当量泥浆密度EUE(external upset end内加厚 FCP(final circulating pressure终了循环压力FH(full hole贯眼扣 GPM(gallon per minute加仑每分HCR(hydraulic control remote valve液动阀 HP(hydrostatic pressure静液柱压力HWDP(heavy weight drillpipe加重钻杆 IADC(international association of drilling contractors钻井承包商 ID(inside diameter内径 IF(internal flush内平扣 KOP(kickoff point造斜点 LOT(leak off test漏失实验 LTC(long thread connection长园扣

常用钻井英语缩写

钻井英语缩写 1.DP drill pipe 钻杆 2.HWDP heavy weight (wall) drill pipe 加重钻杆 3.DC drill collar 钻铤 4.BHA bottom hole assembly 井下钻具组合 5.STB stabilizer 钻杆扶正器 6.PNMDC pony non-magnetic drill collar 短无磁钻铤 7.SMDC short non-magnetic drill collar 短无磁钻铤 8.PDM positive displacement motor 螺杆9.BOP blowout preventer 封井器 10.BOPE blow out preventer equipment 封井器设备 11.IBOP inside blowout preventer 内防喷工具 12.CSG casing 套管 13.TBG tubing 油管

14.JNT/JT joint 单根 15.XO cross-over 配合接头 16.IF internal flush 内平 17.FH full hole 贯眼 18.REG regular 正规 19.IU internal upset 内加厚 20.EU external upset 外加厚 21.EUE external upset 外加厚 22.IEU internal＆external upset 内外加厚 23.OH open hole 裸眼 24.WOB weight on bit 钻压 25.RPM revolutions per minute 转速/分钟 26.SPM strokes per minute 冲程/每分钟 27.ECD equivalent circulating density 当量泥浆密度 28.MT metric ton 公制吨 29.DST drill stem test 钻

石油工程专业英语单词总结

3-D seismic survey (D: dimension:) 三维地震勘探 5-spot pattern n.五点井网Abandon v.（油井）报废，废弃Abandon well n.废井Acid wash n.酸洗 Acidization n.酸化（作用）Acidization n.酸化（作用） Acidize v.酸化Additive n.添加剂 Agent n.试剂，媒介Alkane n.烷烃，链烷烃 Analytic solution n.解析解Anisotropic a.各向异性的，非均质的Annular a.环形的Annular mist flow n.环雾流 Annulus n.环形空间，环空Anticline n.背斜 API standards n.美国石油协会标准Aromatic n.芳香族，芳香族环烃；a. 芳香的 Artifical lift n.人工举升Artificial lift n.人工举升 Artificial water drive n.人工注水驱Asphaltene n.沥青烯 Asphaltic a.含沥青的，沥青质的；n.沥青质Associated a.伴生的 Attribute n.属性，特征，标志Baffle n.隔板；v.阻碍，挫折Barefoot completion n.裸眼完井Barite n.重晶石 Barrel n.桶Barrier n.隔层 Bbl (blue barrel) Bean n.油嘴，节流器 Belt cover n.皮带盖Bentonite n.膨润土，斑脱岩 Bit n.钻头Black-oil simulator n.黑油模拟器Blender truck n.混砂车Blow out v.井喷 Blowout n.井喷Blowout preventer (BOP) n.防喷器Borehole n.井眼Bottom hole n.井下 Collapse v.坍塌，倒塌Collar n.钻铤 Compaction n.压实作用Compaction n.压实（作用），挤压Completion n.完井，完成，结束Compress v.压缩 Compressor n.压缩机Concentration n.浓度；集中Condensate n.凝析油Condensate n.凝析油 Conductor casing n.导管Conductor casing n.导管 Conductor hole n.导管孔Conductor pipe n.导管 Cone n.圆锥，（锥形）牙轮Configuration n.构造 Connate a.原生的，共生的Connate water n.原生水，共生水Contaminant n.杂质，污染物Continuous lift n.连续气举 Core n.岩心Core n.岩心 Core holder n.岩心夹持器Core slug n.岩心塞 Coring bit n.取芯钻头Corrode v.腐蚀 Corrode v.腐蚀，侵蚀；锈蚀Corrosion n.腐蚀 Corrosion n.腐蚀Corrosive a.腐蚀的；n.腐蚀剂Corrosive a.腐蚀的；n.腐蚀剂Counterbalance n.平衡（块）；v.使平衡，抵消 Counterweight n.平衡块Crack v.裂开 Crank n.曲柄，摇把Crown block n.钻台 Crumble v.坍塌，破碎Crust n.地壳 Curve n.曲线Cutting/chips n.钻屑

石油钻井英语词汇

对照实物确认的钻井词汇一、井口与井控 1.套管头升高短节（上下由法兰连接，中间是三通或四通）casing spool 2.油管悬挂器tubing hanger 3.油管悬挂器上边接有阀门的盖子tubing bonnet 4.（可焊接的）导管头（接箍）conductor connector 5.（可焊接的）套管头（接箍）casing connector 6.井口帽blanking cap & plug 7.三闸板防喷器triple slide-lok preventer 8.双闸板防喷器double slide-lok prevente 9.油/套管升高短节tubing/casing riser 10.整体式升高短节integral union riser 11.法兰×丝扣井口转换头wellhead adapter 12.井口四通两边的横向阀门wing valves 13.油管悬挂器上边的变径法兰大小头bonnet 14.上边是法兰的套管头casing flange 15.只上边是法兰，下边与表层套管焊接的套管头casing head 16.套管头内的卡瓦casing slips 17.（上法兰小，下法兰大）变径套管头casing spool crossover 18.与导管焊接的坐在圆井底的套管头landing head flange top 19.卡瓦密封套管悬挂器slips seal casing hanger

20.（上下是法兰，中间是四通的）油管升高短节tubing spool 21.柔性封隔闸板flexpacker ram 22.可变径闸板variable bore ram 23.剪切闸板shearing blind ram 24.卡瓦型套管悬挂器slip-type casing hangers 25.高负荷悬挂器high-load hanger 26.悬挂器断开式密封圈hanger isolation seal ring 27.井口封隔变径变压法兰（中间有几道密封圈，下边是低压，上边是高压）packoff/crossover flange 28.油管头（下法兰大，内带密封圈；中间是四通，上法兰小）tubing heads 29.底（下）变径法兰（下边内径大，上边内径小）basic adapter 30.单密封变径法兰（下内径大，上内径小）single seal bore adapter 31.变径大小头（下边是法兰，上边是本体上钻孔攻丝扣）coupling adapter 32.油管悬挂器转换大小头短节（上法兰小，下法兰大，下法兰内有丝扣）tubingsuspension adapter 33.双油管悬挂器dual completion tubing hanger 34.双密封孔连接法兰dual seal bore adapter 35.锁紧螺丝lockdown screw 36.（地面）单油管密封总成single packer completion 37.法兰式采油树盖子flanged tree caps 38.扰性油管悬挂器coiled tubing hanger

(完整版)石油钻井工程英语词汇

地址：北京市朝阳区东三环中路7号财富中心A 座601 邮编：100020 石油钻井工程英语词汇 2008-10-15 第一章：石油钻井工程英语基础词汇第1 节石油钻井工程基础词汇钻井：drill 定向斜井：directional drilling 欠平衡钻井：under-balance drilling 海上钻井：off-shore drilling 陆地钻井： on-shore drilling 钻头：drill bit 刮刀钻头：drag bit 牙轮钻头：rock bit (镶齿钻头insert bit, 钢齿钻头steel toothed bit) 金刚石钻头：diamond bit 取心钻头：coring bit 钻头浮阀：float valve 钻头水眼：bit nozzle(or jet) 钻头水眼刺:bit nozzle washed out 钻头规：bit caliper(bit gauge) 钻头泥包：bit is balling 钻头钝了，我建议现在起钻：bit is dull. I suggest to POOH now

钻铤：DC(drill collar ) 光钻铤slick drill collar，螺旋钻铤spiral drill collar 钻杆：DP(drill pipe ) 方钻杆：kelly 公扣：pin end 母扣：box end 内平式连接：IF(internal flash) 正规式连接：REG(regular) 贯眼式连接：FH(full hole)加重钻杆heavy weight drill pipe 短钻杆pop joint 井下马达：downhole motor 涡轮钻具：turbine 震击器：drilling jar 减震器：absorber 下部钻具组合：BHA（bottom hole assembly）钻具扶正器：stabilizer（string stabilizer, near-bit stabilizer）钻机：drill rig 钻井泥浆：drilling mud 钻井液：drilling fluid 钻井设备：drilling equipment油：oil 原油：crude oil 天然气：nature gas 煤层气：coal-bed gas 石油：petroleum 中国石油（简称）：CNPC（China National Petroleum Corporation ）长城钻井（简称）：GWDC(Great Wall Drilling Company) 采油：oil production 产油层(目的层)：reservoir( or pay zone) 钻进：drilling 调整钻井参数以得到理想的机械钻速： play the drilling parameters to get fast ROP 起钻：POOH(pull out of hole) 下钻：RIH(run in hole) 下套管：run casing(or RIH with casing) 短起下钻：wiper trip 循环泥浆：circulate 泥浆：reverse circulate 中途循环泥浆：break circulation 分段下钻：RIH in stages 通井：control trip 划眼：reaming 倒划眼：back reaming

钻井现场常用英语专业词汇

Accumulator 储能器 Active tank 循环池 Adjusting bolt （刹把）调节螺栓Admission pipe 进气管 Agitator 搅拌器 Air chamber 空气包 Air line 气管线 Air-operated hoist 气动绞车Alternating current drive 交流电驱动Annular BOP 环形BOP Ato-muffler 消音器 Ball valve 球阀 Bell nipple 井口喇叭管 Bench vise 老虎钳 bit breaker 钻头装卸器 bit gauge 钻头规 blind ram preventer 盲板防喷器BOP control panel 防喷器控制盘BOP deck 防喷器平台 Bottom plug 底塞 Brake lever (brake handle) 刹把Brake line (brake staple) 刹带Bridge plug 桥塞 Buttress 梯形扣 Butterfly valve 蝶阀 By-pass 旁通 By-pass plug 旁通塞 Calipers 卡钳 Casing coupling 套管接箍 Casing cutter 套管割刀 Casing elevator 套管吊卡 Casing hanger 套管悬挂器 Casing head 套管头 Casing monkey board 套管平台Casing scraper 刮管器 Casing shoe 套管鞋 Casing slip 套管卡瓦 Casing spear 套管打捞矛 Casing spool 套管四通 Casing tong 套管大钳 Cat line 猫头绳 Cat line grip 猫头绳爪 Cat shaft 猫头轴 Cat-head 猫头 Cellar deck 井口甲板Cement 水泥 Cement basket 水泥伞 Cement plug 水泥塞 Cement retainer 水泥阻流环 Cementing bond log 固井质量检查Cementing head 水泥头 Cementing line 固井管线 Cementing pump 固井泵 Chain 链 Chain pipe tong 链钳 Chain tong 链钳 Chamber 房间，寝室 Chamber gate 阀箱，闸室 Charge pump 灌注泵 Check valve 止回阀，回压凡尔 Choke 节流器，阻流器 Choke line 阻流管线 Choke position indicator 节流阀位置指示器Choke valve 节流阀 Choke-line manifold 阻流管汇 Clutch 离合器 Conductor 导管 Cone 牙轮 Cone fisher 牙轮打捞器 Cone lock 牙轮卡死 Cooling-water pump 冷却水泵 Core barrel shoe 取心筒鞋 Core basket 取心爪 Core bit 取心钻头 Core catcher 取心爪 Core catch case 取心爪外套 Core drying oven 岩心烘箱 Crossover joint(x/o) 变换接头 Crown block 天车 Crown block beam 天车梁 Dead line 死绳 Dead line diaphragm 死绳固定器膜片Dead line anchor 死绳固定器 Degasser 除气器 Derrick 井架 Desander (desilter) 除砂器（除泥器）Direct current drive 直流电驱动Discharge line 排除管线 Double ram type preventer 双闸板防喷器Down hole tool 入井工具

钻井英文词汇表

顶驱&钻井英文常用词汇表（第一版）盘锦辽河油田天意石油装备有限公司 2010年9月

一、顶驱英文顶部驱动系统Top drive system 车载钻机truck-mounted rig 机械的mechanical 电学的electrical 液压的hydraulic 钻井设备drilling equipment 大斜度井high-inclination well 深井deep well 丛式定向钻井cluster directional well 低温顶驱low-temperature top drive system 超深井ultra-deep well 定向井directional well 载荷load capacity 工作高度working height 电动机motor 功率power 转速rotary speed 钻井扭矩drilling torque 过载能力over load capacity 卸扣break out 上扣make-up 循环压力circulation pressure 额定压力rated pressure 电源电压power voltage 电源频率power frequency 工作电流working current 通风机ventilator 接线箱junction box 平衡油缸counterbalance cylinder 盘式刹车disc brake 电缆接插件cable connector assembly 主电机main motor 液压阀组hydraulic valve block 提环bail 鹅颈管gooseneck 油箱tank 蓄能器accumulator 齿轮箱gearbox 冲管总成wash pipe assembly 液压马达hydraulic motor 回转头rotating head 导轨guide beam 倾斜油缸tilt cylinder 防松法兰lock flange 背钳back-up tong 导向器stabbing guide 遥控IBOP upper IBOP 手动IBOP lower IBOP 吊环link 吊卡elevator 齿轮轴gear shaft 冷却风机Cooling motor 交流电机 AC motor 水龙头 Swivel 主齿轮 Driving gear 编码器 Encoder 散热器 Radiator 油道 Oil passage 密封槽Seal groove 轴承 bearing 滚轮 Roller 滑套 IBOP actuator shell 曲柄 Crank 销pin 钳牙tongdies 活塞piston 螺栓bolt 黄油grease 小车总成 Carriage accessory 气流 Air current 风道 Air duct 进风口 Air inlet 出风口 Air outlet 梨型环 Pear link 卡箍clamping band 键key

钻井英语简写

钻井英语缩写 Abbreviation DP Drill pipe 钻杆 HWDP heavy weight drill pipe 加重钻杆 DC drill collar 钻铤 STB stabilizer 钻杆扶正器 SMDC short magnetic drill collar 短无磁钻铤PDM positive displacement motor 螺杆 NMDC nonmagnetic drill collar 无磁钻铤（钻具）BOP blowout preventer 封井器 CSC casing 套管 JNT joint 单根 XO cross-over 配合接头 IF internal flush 内平 FH full hole 贯眼 REG regular 正规 IU internal upset 内加厚 EU external upset 外加厚 IEU internal & external upset 内外加厚 OH open hole 裸眼 WOB weight on bit 钻压 RPM revolutions per minute 转速分钟 SPM strokes per minute 冲程每分钟 ECD equivalent circulating density 当量泥浆密度MT metric ton 公制吨 BHA bottom hole assembly 底部钻具组合 DST drill stem test 钻具测试 KS key seat 键槽 STDS stands 立柱 VIS viscosity 粘度 WL water loss 失水 PV plastic viscosity 塑性粘度 YP yield point 屈服值 FL filtrate loss 滤失 TVD true vertical depth 垂深 MD measured depth 测量井深 TD total depth 总井深 KOP kick off point 造斜点 DIR direction 定向 AZM azimuth 方位 DEV deviation 井斜 ROP rate of penetration 机械钻速 ID inside-diameter 外径

石油钻井单词翻译

Useful words of drilling常用钻井词汇 Senior mud engineer Driller toolpusHer roughnecks derrickman floorman 高级泥浆工程师司钻、队长、钻工、井架工场地工 Spud in Drill a well Stop Drilling Had Drilled/About 300Msdeep Be Drilling Drilling out of.. Finish drill ..In charge of.. 开钻打一口井停钻已经钻了约300米正在钻进钻完….完钻…负责人W..is? responsible to？…Ｗ..is ?responsible for？get every thing ready for..ing ？向谁负责？.. ？..负责什么？做…准备 ….ｗｈｏｍ.. ..ｗｈｏ.. 是.你们.的人是在.的人. nsbDRILLER'S Month, console log method station tour report monitor 钻机月、司钻（控制台、记录司钻法、平台钻井班报表监视器） DRILL extractor floor fluid footage free gauge hole hole returns hole survey in 钻井（打捞器钻台液进尺空转钻头规眼井口返浆测斜打开生产层）drill ability able liner able packer ahead assembly cable bit run expert collar collar annulus （可钻性可钻尾挂器可钻封隔器继续钻进钻柱组合钢丝行程专家钻挺钻挺环空）DRILL collar bore stem test string assemb limitation fatigue mechanics torque crew （钻挺水眼中测钻柱（结构强度疲劳力学扭矩井队）DRILL rig tool mill monitor off test out tool rope sample site solids stem bushing （钻机、钻具洗靴参数仪试钻钻塞工具棕绳砂样井场岩宵弯曲） DRILL PIPE annulus bore pin box clamp coupling cutter electric log elevator float frozen gauge inspection 钻杆（环空水眼公扣母扣卡瓦接箍割刀钻杆电测吊卡回凡尔卡钻丝扣规钻杆检查）DRILL PIPE protector release spinner stabilizer stand sticking sub tension winding up 钻杆（护丝钻具解卡旋扣器扶正器/稳定器立柱卡钻接头拉力弯曲） DRILLING engineer supervisor superntendent technique experience technology specialist technician （工程师监督总监技术经验工艺专家技术员）DRILLING analytical bit break capacity centralizer contract cost crew cycle data base effort engineering （分析钻头放空能力钻井扶正器合同成本队周期数据库工作量工程学）DRILLING equipment experience hanger load log mud operation optimization operator out outfit parameter （设备经验尾挂器钻压录井泥浆作业优化钻井承包商钻塞设备参数）DRILLING foreman hose implementer in balance instrument interval invasion zone jar journey line liner liner reel 钻井（队长/工头水龙带人员平衡钻进仪表井段漏层震击器记录表大绳尾管滚筒）DRILLING people permit phase prediction pressure program progress rate rate of trip record ship site speed （人员许可权阶段预报压力程序进度钻速行程钻速记录船井场钻速）DRILLING spool stem string stabilizer to completion tool substitute up weight turbine unit （四通钻柱钻柱扶正器钻至设计井深钻具接头钻碎钻压涡轮钻机组） DRILLING time log time work completion operation condition cleaning system bottoms up （钻时记录时间工作完井作业条件净化系统）迟到时间 pull of hole run in hole make up a joint break down a joint trip out of hole laying down wire line survey 起钻下钻接单根卸单根起钻甩钻具吊测 direction al well定向井词汇 DIRECTIONAL well angle bit bit side force component clinograph control counter depth migration 定向（定向井方位角钻头变方位侧向分力方位测斜仪方位控制计数器定向深度偏移）DIRECTIONAL diagram drilling drilling contractor drill tool Effect gyro hole line orientation tool presentation 定向(方位图定向钻井定向井承包商定向钻井工具效应陀螺仪井方向线定向工具方位显示) DIRECTIONAl reading scanning sub surveillance survey tendency tool turbodrill MWD survey tool 定向(方角读数定向扫描接头定向监测定向测量方向趋势随钻测斜仪定向涡轮随钻测量定向测量工具) direction sensor instrument of tilt of deflection of magnetization of strata parameter finding chart azimuth 方向（传感器方向仪倾斜方向井斜方位磁化方向地层走向方向参数测向系统）方向角deflecting tool angle build up angle drop off single shot inclinometer gyroscope whipstock horizontal well orbit 造斜工具增斜降斜单点测斜仪陀螺仪变向器）水平井轨迹Measure Depth Vertical Depth True Vertical Depth Displancement Closure Depth Vertica section Hole Inclination Hole Angle 井深/斜深垂深垂深水位/闭和距水位/闭和距视平移井斜角井斜角Declination Maximum Hole Angle Hole Direction Kick Off Point Dogleg Severity Target Tool face High Side Tool face Angle 慈偏角最大井斜角方位角造斜点全角变化率目标点工具面高边工具面角 sits the mark horizontal segment kick-off segment kick-off rate horizontal departure horizontal displacement 坐标水平段造斜段造斜率水平位移水平位移

常用钻井英语缩写

标准文档钻井英语缩写motor 螺杆 9.BOP blowout preventer 1.DP drill pipe 钻杆封井器HWDP heavy weight (wall) 2. 10.BOPE drill pipe 加重钻杆blow out preventer equipment 封井器设备3.DC drill collar 钻铤 11.IBOP inside blowout bottom 4.BHA hole assembly 井下钻具组合内防喷工具preventer 套管casing 12. 5.STB stabilizer 钻杆扶正器CSG 油管non-magnetic pony tubing 13.TBG 6.PNMDC drill collar 单根JNT/JT 短无磁钻铤joint 14. 7.SMDC short 配合接头cross-over 15.non-magnetic XO drill collar 短无磁钻铤内平internal flush IF 16. 8.PDM 贯眼full hole displacement positive FH 17.实用大全．标准文档 18.REG regular 正规27.ECD equivalent circulating

density 当量泥浆密度19.IU internal upset 内加厚 28.MT metric ton 公制吨20.EU external upset 外加厚29. DST drill stem test 外加21.EUE external upset 钻具测试厚 30.l22.IEU interna＆external KS key seat 键槽 31.KSW key seat wiper 内外加厚upset 键槽清洁器裸眼open hole OH 23. 32.STDS stands 钻压weight on bit WOB 24.立柱 33.VIS viscosity revolutions per minute RPM 25.粘度塑性viscosity 34.PV 分钟/转速plastic strokes SPM 26. minute per 粘度冲程/屈服值yield point 每分钟YP 35.实用大全．标准文档 36.FL filtrate loss 滤失45.AZM azimuth 方位 46.water loss 失水DEV deviation 井斜37.WL https://www.wendangku.net/doc/357462027.html,D true vertical depth ROP rate of penetration 机械转速垂深 48.ID 测量inside-diameter 内径depth 39.MD measured 49.井深OD outside diameter 外径 50.FTG footage 40.TD total depth 总井深进尺 51. plug back total depth PPG pounds per gallon 41.PBTD 人工井底（密度）每加仑磅inch pounds per square 52. piece

石油钻井词汇

石油钻井词汇 Part One SLICK-LINE（钢丝作业） A. TOOLS rope socket 绳帽 stem 加重杆 roll stem 滚轮加重杆 Tungsten stem 钨加重杆 Lead stem 铅加重杆 link jar 机械震击器 tubular jar 管状震击器 hydraulic jar 液压震击器 spring jar 弹簧震击器 knuckle joint 万向节 swivel joint 旋转节 wellhead adapter 井口变扣短节 X-Over 变扣 gauge cutter 通井规 selective downshift tool 选择性滑套开关工具 shiftting tool 移位工具 blind box 盲锤 L.I.B(lead impression block) 铅印swaging tool 胀管器 spear 打捞矛 prong grab 内捞矛 center spear 外捞矛 catcher 捕捉器 wirefinder 钢丝探测器 Go devil-F.B 平底撞棍 Go devil-C.B 刀杆撞棍 retriever 钢丝打捞器 overshot 卡瓦打捞筒 magnetic fishing tool 磁力打捞工具sidewall cutter 刮管刀 alligator grab 鳄鱼爪 sand bailer 捞沙筒 pipe wrench 管钳 tong chain 链钳 spanner 扳手 wireline clamp 钢丝夹 hay pulley 地滑轮 dump bailer 倾倒筒 saw 锯子 saw blade 锯条 punch 冲子 file 锉刀 flat file 板锉,扁锉 hammer 榔头 pliers,vice 老虎钳 wire cutter 断线钳forfex 剪刀 tongs 大钳,钳子,管钳 flat bit tongs 扁嘴钳 screwdriver 改锥，螺丝刀 wire stripper 剥皮钳,掳线钳 wire-stripper pliers 剥线钳 B. EQUIPMENT stuffing box 防喷盒 lubricator upper section 上防喷管 lubricator middle section 中防喷管 lubricator lower section 下防喷管 blowout preventer(BOP) 防喷器 wellhead adapter 井口变扣短节 Lincoln pump 林肯泵 hand pump assy.for stuffing box 手压泵 Fire extinguisher 灭火器 hand tool box 手工具箱 injector 注油器 lifting cap BOP吊帽 trolly 防喷管支撑架 parasol 阳伞 work vice 台钳 chain block 链葫芦 tie down chain 系紧链 fixed pulley 定滑轮 wobble pump 手摇泵 wire line clamp 钢丝绳夹 wire rope sling 绳套,钢丝吊绳 winch 绞车 winch barrel(drum) 绞车滚筒 winch brake 绞车刹车 winch drive shaft universal joint 绞车主动轴万向节 winch drum shaft 绞车滚动轴 winch line 吊装用绳套 winch control panel 绞车控制面板 winch truck 吊车 C. OPERATIONS RTTS Operation for Shoot and Pull RTTS完井服务 RTTS Operation for Cement Squeezing RTTS固井服务（挤水泥） Pulling Y Block 捞Y堵塞器 Open SSD(Slide Side Door) 开生产滑套 Close SSD(Slide Side Door) 关生产滑套 Open Circulating SSD(Slide Side Door) 开循环滑套 Close Circulating SSD(Slide Side Door) 关循环滑套 Running Gauge Cutter 通井 Clean up 地面完井放喷 Open Drain Valve 砸泻油阀 Pulling Test Plug 捞测试阀 Running Jet Pump 投射流泵 Pulling Jet Pump 捞射流泵 Running Flow Regulator 投配水器 Pulling Flow Regulator 捞配水器 Fishing Drop Bar 捞点火棒 Measuring Static Pressure 测静压 Measuring Flowing Pressure 测流压 Measuring BHPBU(Bottom Hole Pressure Build Up) 测压力恢复 Measuring BHP(Bottom Hole Pressure) Testing with Jet Pump 带泵测压（射流泵） Multi-Rate BHP(Bottom Hole Pressure) Testing 系统试井 Slick-line Operation for Completion 钢丝配合完井服务 Slick-line Operation for acidizing 配合酸化钢丝作业 Running Plug 投堵塞器 Pulling Plug 捞堵塞器 Run Impression Block 下铅印 Running Prong 投平衡杆 Sand Level detection 探沙面 Run Sand Bailer 下捞砂桶 Open SSSV(Sub Surface Safety Valve) by Force 强行打开井下安全阀 Running Go Devil 剪切钢丝 Fishing Slickline 打捞钢丝 Running Side Pocket Plug 投偏心堵塞器 Pulling Side pocket Plug 捞偏心堵塞器 Running Side Pocket Check Valve 投偏心阀 Pulling Side Pocket Check Valve 捞偏心阀 Sand Sampling 取砂样 Stable Test 稳定试井 Slickline Swab 抽吸 Running Hanger 投悬挂器 Pulling Hanger 捞悬挂器 D. SPARE PARTS

海上钻井英语500句

钻井英语常用词汇及术语缩写.

常用钻井英语缩写

石油工程专业英语单词总结

石油钻井英语词汇

(完整版)石油钻井工程英语词汇

钻井现场常用英语专业词汇

钻井英文词汇表

钻井英语简写

石油钻井单词翻译

常用钻井英语缩写

石油钻井词汇

最新钻井缩写大全