BTA40-700B中文资料
?
1/7
Table 1: Main Features
DESCRIPTION
Available in high power packages, the BTA/BTB40-41 series is suitable for general purpose AC switching. They can be used as an ON/OFF function in applications such as static relays, heat-ing regulation, induction motor starting circuits... or for phase control operation in light dimmers, motor speed controllers, ...
Thanks to their clip assembly technique, they provide a superior performance in surge current handling capabilities.
By using an internal ceramic pad, the BTA series provides voltage insulated tab (rated at 2500V RMS ) complying with UL standards (File ref.:E81734).
Symbol Value Unit I T(RMS)40A V DRM /V RRM 600 and 800
V I GT (Q 1)
50
mA
BTA40, BTA41 and BTB41 Series
40A TRIAC S
REV. 7October 2005STANDARD
Table 2: Order Codes
Part Number Marking BTA40-xxxB See table 8 on page 6
BTA41-xxxBRG BTB41-xxxBRG
BTA40, BTA41 and BTB41 Series
2/7
Table 3: Absolute Maximum Ratings Tables 4: Electrical Characteristics (T j = 25°C, unless otherwise specified)Table 5: Static Characteristics Symbol Parameter
Value Unit I T(RMS)RMS on-state current (full sine wave)
RD91 / TOP3T c = 95°C 40A TOP Ins.
T c = 80°C I TSM Non repetitive surge peak on-state current (full cycle, T j initial = 25°C) F = 50 Hz t = 20 ms 400A F = 60 Hz t = 16.7 ms
420I 2t I 2t Value for fusing
t p = 10 ms 880
A 2s dI/dt
Critical rate of rise of on-state cur-rent I G = 2 x I GT , t r ≤ 100 ns
F = 120 Hz
T j = 125°C 50A/μs V DSM /V RSM Non repetitive surge peak off-state voltage
t p = 10 ms
T j = 25°C V DSM /V RSM + 100
V I GM Peak gate current
t p = 20 μs
T j = 125°C 8A P G(AV)Average gate power dissipation T j = 125°C
1W T stg T j
Storage junction temperature range Operating junction temperature range
- 40 to + 150- 40 to + 125
°C
Symbol Test Conditions
Quadrant Value Unit I GT (1)V D = 12 V R L = 33 ?
I - II - III IV MAX.50100mA V GT ALL MAX. 1.3V V GD V D = V DRM R L = 3.3 k ? T j = 125°C ALL
MIN.0.2V I H (2)I T = 500 mA MAX.80mA I L I G = 1.2 I GT
I - III - IV
MAX.70mA II 160dV/dt (2)
V D = 67 %V DRM gate open
T j = 125°C MIN.500V/μs (dV/dt)c (2)(dI/dt)c = 20 A/ms
T j = 125°C
MIN.
10
V/μs
Symbol Test Conditions
Value Unit V T (2)I TM = 60 A t p = 380 μs
T j = 25°C MAX. 1.55V V t0 (2)Threshold voltage T j = 125°C MAX.0.85V R d (2)Dynamic resistance T j = 125°C MAX.10m ?I DRM I RRM
V DRM = V RRM
T j = 25°C MAX.
5μA T j = 125°C
5
mA
Note 1: minimum I GT is guaranted at 5% of I GT max.Note 2: for both polarities of A2 referenced to A1.
BTA40, BTA41 and BTB41 Series
3/7
Table 6: Thermal resistance Symbol Parameter
Value Unit R th(j-c)Junction to case (AC)RD91 (Insulated) / TOP30.9°C/W TOP3 Insulated 0.6R th(j-a)
Junction to ambient
TOP3 / TOP3 Insulated
50
°C/W
S = Copper surface under tab.
Figure 1: Maximum power dissipation versus RMS on-state current (full cycle)
Figure 2: RMS on-state current versus case temperature (full cycle)
Figure 3: Relative variation of thermal impedance versus pulse duration
Figure 4: On-state characteristics (maximum
values)
BTA40, BTA41 and BTB41 Series
4/7
Figure 5: Surge peak on-state current versus number of cycles
Figure 6: Non-repetitive surge peak on-state current for a sinusoidal pulse with width t p < 10 ms and corresponding value of I 2t
Figure 7: Relative variation of gate trigger current, holding current and latching current versus junction temperature (typical values)
Figure 8: Relative variation of critical rate of decrease of main current versus (dV/dt)c (typical values)
Figure 9: Relative variation of critical rate of decrease of main current versus (dV/dt)c
BTA40, BTA41 and BTB41 Series
5/7
Figure 10: Ordering Information Scheme
Table 7: Product Selector
Part Numbers Voltage (xxx)Sensitivity Type Package 600 V 800 V BTA40-xxxB X X 50 mA Standard RD91BTA41-xxxBRG X X 50 mA Standard TOP3 Ins.BTB41-xxxBRG
X
X
50 mA
Standard
TOP3
BTB: non insulated TOP3 package
BTA40, BTA41 and BTB41 Series
6/7
In order to meet environmental requirements, ST offers these devices in ECOPACK? packages. These packages have a Lead-free second level interconnect . The category of second level interconnect is marked on the package and on the inner box label, in compliance with JEDEC Standard JESD97. The maximum ratings related to soldering conditions are also marked on the inner box label. ECOPACK is an ST trademark. ECOPACK specifications are available at: https://www.wendangku.net/doc/4811909027.html,.Table 8: Ordering Information
Ordering type Marking Package Weight Base qty
Delivery mode
BTA40-xxxB BTA40xxxB RD9120 g 25Bulk BTA41-xxxBRG BTA41xxxB TOP3 Ins. 4.5 g 30Tube BTB41-xxxBRG
BTB41xxxB
TOP3
4.5 g
30
Tube
Note: xxx = voltage
Table 9: Revision History
Date Revision
Description of Changes
Sep-20035Last update.
25-Mar-20056TOP3 delivery mode changed from bulk to tube.
14-Oct-2005
7
T c values for I T changed in Table 3. ECOPACK statement added.
BTA40, BTA41 and BTB41 Series Information furnished is believed to be accurate and reliable. However, STMicroelectronics assumes no responsibility for the consequences
of use of such information nor for any infringement of patents or other rights of third parties which may result from its use. No license is granted by implication or otherwise under any patent or patent rights of STMicroelectronics. Specifications mentioned in this publication are subject to change without notice. This publication supersedes and replaces all information previously supplied. STMicroelectronics products are not
authorized for use as critical components in life support devices or systems without express written approval of STMicroelectronics.
The ST logo is a registered trademark of STMicroelectronics.
All other names are the property of their respective owners
? 2005 STMicroelectronics - All rights reserved
STMicroelectronics group of companies
Australia - Belgium - Brazil - Canada - China - Czech Republic - Finland - France - Germany - Hong Kong - India - Israel - Italy - Japan - Malaysia - Malta - Morocco - Singapore - Spain - Sweden - Switzerland - United Kingdom - United States of America
https://www.wendangku.net/doc/4811909027.html,
7/7