CF-61,CF-76datasheet ()

3Cosmetic Fluids CF-61 and CF-76

3M ?Cosmetic Fluids CF-61 and CF-76 are unique, fast-drying solvents that can be in a variety of cosmetics and skin care formulations.

Cosmetic ?uids CF-61 (methoxynona?uorobutane) and CF-76 (ethoxynona?uorobutane)are clear, colorless ?uids with low odor. They are fast drying cosmetic ?uids with boiling points of 61°C and 76°C, respectively. Cosmetic ?uids can be used to replace or in conjunction with alcohol or other fast-drying solvents, such as silicone ?uids and hydrocarbon solvents. 3M Cosmetic Fluids are environmentally favorable ?uids offering a unique balance of properties.

Safety Properties ? Non ?ammable ? Low toxicity

Environmental Properties ? Non-VOC ? Low water solubility

Performance ? Solvency ? Compatibility ? Stability ? Low viscosity Introduction ? Carrier for aerosols

? Solvent and emulsion stabilizer for improved cosmetic formulations

? Alcohol replacement

? Fragrance extraction

Typical Applications

Material Description

CF-61 ?uid (C 4F 9OCH 3) consists of two inseparable isomers with essentially identical properties.These are (CF 3)2CFCF 2OCH 3(CAS No. 163702-08-7) and CF 3CF 2CF 2CF 2OCH 3(CAS No. 163702-07-6).

Information

Product

4925These are (CF 3)2CFCF 2OC 2H 5(CAS No. 163702-06-5) and CF 3CF 2CF 2CF 2OC 2H 5

Not for

speci ?cation

purposes

All values determined

at 25°C unless

otherwise speci ?ed 3M ?Cosmetic Fluids T ypical Physical Properties Comparison

Solvency Data

Note: “Miscible ” = 50% soluble by weight

Compatible after one-hour exposure at boiling temperature.

Exceptions: Some swelling of PTFE and silicone rubber.

Some surface oxidation of copper during heat aging.

*Butyl Rubber best for extended exposure > one month.3M ?Cosmetic Fluids Materials Compatibility

1

CFC-11 = 1.02 GWP – 100 year ITH, CO 2= 1.0

3Quali ?es as South Coast Air Quality Management District (SCAQMD) “Clean Air Solvent ”

Environmental Properties

Testing of 3M ?Cosmetic Fluids CF-61 and CF-76 in neat form demonstrates compatibility

with a wide range of metals, plastics, and elastomers. Although CF-61 and CF-76 ?uids

show good short-term compatibility with ?uorinated plastics and elastomers at room

temperature, the ?uids will absorb into these materials over longer exposure times.

Please note, 3M can work with you and your preferred packaging supplier to determine

optimal packaging for 3M cosmetic ?uid-based formulations.

3M?Cosmetic Fluids Regulatory Status

3M?Cosmetic Fluids CF-61 and CF-76 have been accepted for commercial use by

regulatory agencies in the United States, Canada, Japan, Korea, Australia and Europe

(under the European List of Noti?ed New Chemical Substances).

3M cosmetic ?uids have been approved under the Signi?cant New Alternatives Policy

(SNAP) of the U.S. EP A. In addition, 3M cosmetic ?uids have been excluded by the

U.S. EP A from the de?nition of a VOC on the basis that these compounds have

negligible contribution to tropospheric ozone formation.

Contact your local 3M representative regarding regulatory status and coding assistance

for 3M cosmetic ?uids.

T oxicity Pro?le

The toxicological testing completed on 3M cosmetic ?uids CF-61 and CF-76 indicate that

overall toxicity is low. The materials are practically non-irritating to the eyes, minimally

irritating to the skin and not a mutagen or cardiac sensitizer. They are rated “practically non-

toxic” through inhalation.

* Exposure guidelines established by the American Industrial Hygiene Association

Compatibility / Solubility With T ypical Cosmetic Ingredients

Many of the components that are listed as being insoluble in the CF Fluids remain stable in

emulsions with the CF Fluids.

Before using this product, please read the current product Material Safety Data Sheet

(available through your 3M sales or technical service representative) and the precautionary statement on the product package. Follow all applicable precautions and directions.

Environmental Health and Safety

3M will continue to recognize and exercise its responsibility to: prevent pollution at the

source wherever and whenever possible; develop products that will have minimal effect on

the environment; conserve natural resources through the use of reclamation and other

appropriate methods; assure that its facilities and products meet and sustain the regulations

of all national and other of ?cial organizations engaged in environmental activities.

Environmental Policy

These products are certi ?ed by 3M to contain 50ppb or less of the following heavy metals.Ag, Al, As, B, Cu, Cd, Co, Cr, Cu, Fe, Hg, K, Li, Mg, Mn, Na, Ni, Pb, Sr, Ti, Zn

3M ?Cosmetic Fluids Purity Speci ?cations

3M ?Cosmetic Fluids are non ?ammable and do not exhibit ?ammability characteristics

under normal operating and storage conditions. These ?uids are highly resistant to

thermal breakdown and hydrolysis in storage and during use. Recommended handling

procedures are provided in the pertinent Material Safety Data Sheets available through

your local 3M sales or technical representative upon request.Safety and Handling

3M cosmetic ?uids are supported by global sales, technical and customer service resources,

with fully-staffed technical service laboratories in the U.S., Europe, Japan, Latin America

and Southeast Asia. Users bene ?t from 3M ’s broad technology base and continuing

attention to product development, performance, safety and environmental issues.

For additional technical information on 3M cosmetic ?uids in the United States, call 3M Specialty Materials Division, 800 541 6752.

For other 3M global of ?ces, and information on additional 3M products, visit our web site at: https://www.wendangku.net/doc/4913563106.html,/cosmeticingredients Resources

Packaging and Availability

3M cosmetic ?uids may be ordered in the following container sizes:

? 55-gallon drum (600 lbs, 272.1 kg)

? 3.5-gallon pail (33 lbs, 15 kg)

? 1-gallon pail (12 lbs, 5.4 kg)

? 4-ounce sample (.353 lbs, 160 g)

3M Specialty Materials

3M Center, Building 223-6S-04

St. Paul, MN 55144-10003Important Notice to Purchaser:The information in this publication is based on tests that we believe are reliable. Your results may vary due to differences in test types and conditions. You must evaluate and determine whether the product is suitable for your intended application. Since conditions of product use are outside of our control and vary widely, the following is made in lieu of all express or implied warranties (including the warranties of merchantability or ?tness for a particular purpose): Except where prohibited by law, 3M ’s only obligation and your only remedy, is replacement or, at 3M's option, refund of the original purchase price of product that is shown to have been defective when you received it.In no case will 3M be liable for any direct, indirect, special, incidental, or consequential damages (including, without limitation, lost pro ?ts, goodwill, and business opportunity) based on breach of warranty, condition or contract,negligence, strict tort, or any other legal or equitable theory.

4831 (HB)3M is a trademark of https://www.wendangku.net/doc/4913563106.html,ed under license by 3M subsidiaries and af ?liates.Brazil 3M do Brazil Ltda Via Anhanguera, Km 110Caixa Posta 123CEP 13001-970 Campinas

Sao Paulo, Brazil

55 19 3838 7331Europe 3M Specialty Materials 3M Belgium N. V.Haven 1005, Canadastraat 11B-2070 Zwijndrecht 32 3 250 7511Sumitomo 3M Limited 33-1, Tamagawadai 2-chome Setagaya-ku, Tokyo 158-8583 Japan 813 3709 8250Korea 3M Korea Ltd.22nd Floor Daehan Investment Trust Bldg.27-3 Yoido-dong Yongdungpo-ku Seoul 150-010, Korea

822 3771 4114United States

3M Specialty Materials

3M Center, Building 223-6S-04

St. Paul, MN 55144-1000

800 541 6752Chile 3M Chile S.A.Av. Santa Isabel # 1001Santiago, Chile

56 2 410 3000Taiwan 3M Taiwan Ltd.13th Floor, Lotus Bldg. 136Section 3, Jen Ai Rd.Taipei, 106, Taiwan, R.O.C.Taiwan 886 2 2704 9011China 3M China Ltd.10/F New Town Mansion 55 Loushanguan Road Shanghai 200336, P.R. China 86 21 62753535Philippines 3M Philippines, Inc.PCIbank Tower 2-18th Floor Makati Avenue Makati City 1200

Philippines

63 2 813 37813M Canada

Specialty Materials

P.O. Box 5757

London, Ontario

N6A 4T1

800 364 35773M Argentina S.A.C.I.F.I.A.Los Arboles 8421686 - Hurlingham Provincia de Buenos Aires

Argentina

54 11 4469 8200

54 11 4469 8318 (Fax)Singapore 3M Singapore Pte. Ltd.

9, Tagore Lane

Singapore 787472

Singapore

65 454 8611

Malaysia 3M Malaysia Sdn. Berhad Bangunan 3M, 6, Persiaran Tropicana, 47410 Petaling Jaya, Selangor, Malaysia

60 3 706 2888Birla 3M Limited Bangalore Raheja Paramount,138, Residency Road,Bangalore 560 025India 91 80 223 1414

91 80 223 1450 (Fax)Thailand Limited 12th Floor, Serm-Mitr Tower 159 Asoke Road (Sukhumvit 21)Bangkok 10110Thailand 662 260 8577

662 261 7535(Fax)Mexico 3M Mexico, S.A. de C.V.

Avenida Santa Fe #55

Colonia Santa Fe

Delegaci ón Alvaro Obreg ón

01210 Mexico, D.F.

52 55 5270 0400