中兴PTN命令汇总

查看命令
show run-config
show start-config
show power
show vlan
show inter bri
show ip inter bri
show run interface
show op in xgei_x/y
show lldp neighbor
show run | be router
show run | be snmp
show run | be tunnel
show run | be vfi
show run | be cpi
show boot
show nm
show version
show arp
show mac
show logg notify
show logg courent
show logg histroy
set fan-speed auto /full
ftp-server enable
ftp-server tick-user 1
clear counter gei_x/x
ping ip re 1000 lim 0 快速检车掉包情况

文件操作
wr
sync startrun to agent(6100)
redundancy /red for
write imgfile slave

dir
cd cfg
delete startrun.dat
cd ..
cd db
delete *.*
rename startrun.dat startrun.bak

备份
copy flash: /cfg/startrun.dat ftp: //服务器ip/startrun9000.dat@9000:9000
copy flash: /img/zxr10.zar ftp: //服务器ip/zxr10.zar@9000:9000


copy flash /cfg/startrun.dat ftp //服务器ip/63-1startrun.dat@sysbak:sysbak

上传
copy ftp: //129.12.50.200/zxr10.zar@sysbak:sysbak flash: /img/zxr10.zar

主备对拷：
copy flash /img/zxr10.zar flash /sl_img/zxr10.zar

接口配置
con t
interface gei_x/y
out_index 11
negotiation auto
jumbo-frame enable
switchport mode trunk
switchport trunk native vlan vlan-id
switchport trunk vlan vlan-id
switchport qinq normal
dul full
speed 100/1000

光口自环取消
inerface gei_x/x
no loopback

interface vlan 100
ip add 192.16.1.4 255.255.255.0
set arp static 192.16.1.9 00d0.d061.0601
exit

show vct interface gei_3/1
show this
show run | in mng
Show run | begin cip
Show run | begin vfi

conf t
cip X
oam-maping enable tmpls-oam

修改MAC地址命令
show lacp sys-id 机架MAC（出厂MAC）如果不激活可能和MEMORY和NVRAM的不一致 MEMORY地址必须重启后才能生效
olleh
mac-base-addr show
mac-base-addr show master nvram
mac-base-addr show slave nvram
mac-base-addr show slave mem
mac-base-addr delete master all
mac-base-addr add master XXXX.XXXX.XXXX 16(9008)/8(6300&6200)
mac-base-addr add master mng XXXX.XXXX.XXXX 1
mac-base-addr enable master
mac-base-addr enable slave
reload
mac-base-addr syn

ospf路由宣告
show ip ospf 查看OSPF进程的详细信息
show ip ospf interface 查看OSPF接口的现行配置和状态
show ip ospf neighbor 查看OSPF邻居的信息
show ip ospf database 查看一个链路状态数据库的全部或部分信息
show run | be router

show ip ospf database database-summ 路由器发布了 lsa条目
show ip ospf retransmission-list 是否有重传 检查IP地址冲突常用命令
clear ip ospf proceed 1重启ospf进程


router ospf 1
passive-interface vlan x x监控vlan 多个接入网元监控VLAN隔离
network XXX.XXX.XXX.XXX ZZZ.ZZZ.ZZZ.ZZZ area 0
no network XXX.XXX.XXX.XXX ZZZ.ZZZ.ZZZ.ZZZ area 0

terminal monitor （no）
debug ip ospf all查看信息是否存在ID相通
debug ip ospf adj 打开回送OSPF邻接事件调试信息的

开关
debug ip ospf packet 打开回送OSPF收发包事件调试信息的开关，监听所有OSPF包的接收和发送
debug ip ospf lsa-generation 打开回送OSPF生成链路状态宣告事件调试信息的开关
debug ip ospf events 打开回送OSPF重要事件调试信息的开关
router-id X.X.X.X强行指定新id
clear ip ospf process id

标签无法分配
no tmpls label per-interface enable 重启设备

解决内存泄露
security mode bpdu disable 将端口下的STP协议保护关闭

诊断模式
diag

prjexec drv npc npc 5 cmdname drv_synce_ad_reg_show 1,0x300,0x301
prjexec bcm npc 6 unit 0 cmdname pc clear
prjexec drv npc 6 cmdnam show_arp_tbl
prjexec drv npc 6 cmdname mactableshow
prjexec bcm npc 6 unit 1 cmdname *:pe clear
prjexec drv npc 6 cmdname rosTaskInfoShowp
prjexec bcm npc 1 unit 4 cmdname pe



interface gei_x/y
security mode arp disable 将端口接收ARP报文的功能关掉
L2 switch disable 提供默认关闭vlan1的二层交换功能

域划分
show ip protocol routing
show ip protocol routing summary
show ip ospf database 是否有2条lsa

ABS 0域
Network 139.2.41.3 0.0.0.3 area 2
Area 2 stub no-summary
非ABS域
Network 139.2.41.4 0.0.0.3 area 2
Area 2 stub


show ethernet-oam gei_2/20 discovery
ping 129.15.150.254 source 129.15.102.215
ping 129.15.150.254 source 129.15.102.215 size 5000
tercert 129.15.102.215

生成树
detect-group 1
retry-times 2
time-out 1
detect-list 1 192.168.2.4
exit
ip route 0.0.0.0 0.0.0.0 192.168.2.4 detect-group 1

spanning-tree enable
spanning-tree mst configuration
instance 1 vlans 2

处理EVPL故障流程：
删除A的EVPL业务，保留纬线和隧道。
在原来的Z端口(中心机房业务端口)和A的2个端口(NODE站点PTN设备业务端口)配置EVPTREE业务
登陆Z设备查询:show run | begin ^vfi
在显示里面找到vfi值=X
MSC2-1#show run | begin ^vfi
vfi 176
mode vlan-all
mpls xconnect pw 60 spoke
isolate local-member
isolate spoke-member
vfi-type etree evptree
9008设备里面输入:show mac-table vfi X
MSC2-1#show mac-table vfi 176
MAC Table:
Int:OutIntLab
Ext:OutExtLab
Type Codes:D-dynamic, S-static, F-filter
MAC Peer-address/PW-frr Int Ext OutInterface Typ
00d0.d0a0.36eb Local NULL NULL gei_2/27 D
0015.eb96.8ea2 3.2.2.2 18 3 tunnel3912 D
查看显示 local 表示本端学习到得mac tun***表示 对端学习到的MAC。
登陆到A设备 查询：show mac to-static 是否有MAC地址存在.

0015.eb96.8ea2 0 0 8 0 8 cip8 0 0 0 0 0 0 00:13:35
00d0.d0c7.ffe1 3023 0 0 0 0 gei_7/1 0 0 0 0 0 0 18:46:48
00d0.d0c7.ffe1 123 0 0 0 0 gei_7/1 1 0 0 0 0 1 18:46:57
是否有VIP和CIP?上面结果显示断定是单通，Z能学到下面MAC A学不到上面MAC
最后检查

结果在 ARP表里面的MAC地址不一致

或者命令修改.show run | be service instence
con t
service instence X
no service-type
service-type elan eplan / eline epl
exit
exit
show mac 核实MAC地址


笔记本添加静态路由
开始运行
cmd
cd\
router print
route add 192.168.0.0 mask 255.255.0.0 192.168.204.18 –p


logging on
logging trap-enable informational
clock timezone BEIJING 8
nvram mng-ip-address 192.192.192.11 255.255.255.0


隧道
tunnel 1
tunnel mode tmpls
no tunnel enable
tunnel qos-mode pipe
tunnel tmpls type bidirectional
tunnel tmpls ingress 4.4.4.4 egress 9.9.9.9 out-port gei_1/10 out-label 100 next-hop 192.16.1.9
tunnel tmpls ingress 9.9.9.9 egress 4.4.4.4 in-port gei_1/10 in-label 101
tunnel id 1
tunnel enable
exit

伪线
pwe3 pw1 1
vcid 1 pwtype ethernet local_label 1000 remote_label 1001
traffic-limit cir 100001 cbs 100 pir 100001 pbs 100
exit

EPL（EPLAN EPTREE）
cip 1
service-type uni 1
exit
vip 1
pseudo-wires-id 1
tunnel-binding tunnel 1
vipmode pwotmpls
exit
service instance 1
vip 1
cip 1
service-type eline epl
exit

EVPL业务（EVPLAN EVPTREE）
cip 4
service-type uniport-vlan uni 2 vlan 10-100
exit

vip 5
cevlan-list 10-100
operation-type root
pseudo-wires-id 4
tunnel-binding tunnel 1
horizontally-partitioning disable
vipmode pwotmpls
exit
service instance 2
description evpl
service-type eline evpl
vip 5
cip 6
no remote-mac-learn enable
no local-mac-learn enable
no vlanrmap enable
cevlankeep enable
no coskeep enable
traffic-limit broadcast cir 1000001 cbs 100 pir 1000001 pbs 100
traffic-limit multicast cir 1000001 cbs 100 pir 1000001 pbs 100
traffic-limit unknow-unicast cir 1000001 cbs 100 pir 1000001 pbs 100
exit

非机构化E1（结构化*）
cip 3
service-type port-e1 e1_2/1
*structure aware
*time
exit
vip 3
work-mode tdm-ces
encapsulated-delay 1
pseudo-wires-id 2
tunnel-binding tunnel 1
vipmode pwotmpls
exit
service instance 1
cip 1
vip 1
service-type ces ces
exit

ATM业务
controller e1_2/2
framing PCM31
exit
ima 1
bind e1_2/1 icp-offset 12
bind e1_2/2 icp-offset 12
exit
atm 1
service-type ima 1
exit
pwe3 c 3
vcid 3 pwtype ethernet local_label 1000 remote_label 2000
pw-control-word enable
pw-sequence disable
traffic-limit cir 1001 cbs 1001 pir 1001 pbs 1001
exit
vip 3
work-mode atm-ces
cell 1
pseudo-wires-id 3
tunnel-binding tunnel 1
vipmode pwotmpls
exit
service instance 3
atm-pvc 1 cip-in 3 vip-out 3 vpi-in 1 1 vpi-out 1 1
atm-pvc 2 vip-in 3 cip-out 3 vpi-in 1 1 vpi-out 1 1
cip 3
vip 3
service-type ces ces
exit

ACL配置
qos-ds-domain
exit
acl hybrid number 300
rule 1 permit any
exit
rule-group acl-no 300 1 match rule-id 1
traffic-limit 300 rule-group 1 ef cir 104857 cbs 104857
interface fei_1/1
ip access-group 300 in
exit

TMS配置
tms 1
local-port gei_1/9 peer-port 192.16.1.9
tmpls oam meg 1
tmpls oam m

eg-id 1
tmpls oam meg speed fast
tmpls oam meg mode end

tmpls oam local-mep 2 type bid
tmpls oam peer-mep 1 type bid
tmpls oam cv
tmpls oam cv cc
tmpls oam cv period 3.33ms
tmpls oam enable
exit

OAM配置
tmpls oam meg1
tmpls oam meg-id 1
tmpls oam local-mep 194 type bid
tmpls oam peer-mep 149 type bid
tmpls oam cv
tmpls oam cv period 3.33ms
tmpls oam cv cc
tmpls oam enable
exit

保护组
tunnel group 1
group type protect
group mode tmpls
protect type 1plus1
protect mode revertive
protect next 192.16.1.9
protect working-meg 1
protect protect-meg 2
group working-tunnel 1
group protect-tunnel 2
protect en
exit


检查保护组配置
show run | be tunnel group
prjexec l3switch tmpls mp group 1

光模块电源故障检测
1.1版本：prj drv bcm npc [panel号] showphyreg [port] 端口号1-8
2.0 版本：prjexec drv npc [panel号] show phyreg [port] 端口号1-8
prjexec drv bcm-shell npc 1 showphyreg 1

OAM信息检测
diag execute mp master cmd showallmeg


prjexec l3switch tmpls mp tunnel 0 diag exec mp ma smd show_tunnel 0
prjexec l3switch tmpls mp group 0
prjexec l3switch tmpls mp pw 0
prjexec l3switch tmpls mp vip 0
prjexec l3switch tmpls mp service 0
prjexec l3switch tmpls mp cip 0

diag execute mp master cmd showmegindex 32
prjexec l3switch tmpls-oam mp megindex 32 cv
diag execute mp master cmd showmegindex 32 , 2
diag execute mp master cmd showmegpoint 32
prjexec drv bcm-shell npc 8 showoamcount 1
prjexec drv bcm-shell npc 8 showfpga
prjexec drv bcm-shell npc 8 showphy
diag execute mp master cmd panelinfoshow 8
prjexec drv bcm-shell mp show c ge48
prjexec drv bcm-shell mp show c ge8
diag execute mp master cmd SspFpgaShowResvInt
prjexec mux total-pkt-cnt
prjexec mux mux-pkt receive
diag execute mp master cmd SspFpgaShow4kIndTable 2
diag execute mp master cmd errlistall
diag execute mp master cmd show_log
diag execute mp master cmd show_trace
diag execute mp master cmd show_trace_err
diag execute mp master cmd show_switch
diag execute mp master cmd show_oam
diag execute mp master cmd show_aps
prjexec l3switch tmpls mp tms
prjexec l3switch tmpls mp tmrp
diag exec mp master cmd showport 1,3
prjexec drv bcm-shell mp mirrorhwshow
show vct interface gei_1/1