SASO 443
METHODS OF TESTING FOR PLUGS AND SOCKET OUTLETS FOR VOLTAGES UP TO 220 V FOR HOUSEHOLD AND SIMILAR GENERAL USE
METHODS OF TESTING FOR PLUGS AND SOCKET OUTLETS FOR VOLTAGES UP TO 220 V FOR HOUSEHOLD AND SIMILAR GENERAL USE
ICS:
Date of SASO Board of Directors' Approval : 1424(H)-09-07 (2003-11-01) Date of Publication in the Official Gazette :
Date of Enforcement of this Standard :
CONTENTS
Item Page 1. Scope (2)
references (2)
2. Supplementary
3. Requirements (2)
inspection (2)
4. Visual
5. Measurement of Dimensions (2)
6. Insulation Resistance Test (3)
7. Electric strength test (3)
8. Withdrawal force test (3)
9. Contact Resistance test (4)
10. Temperature Rise test (4)
11. Current Breaking capacity of socket-contacts (5)
12. Current Breaking capacity of switches (For switched socket-outlet) (5)
13. Electrical Endurance of socket - contacts (5)
14. Electrical endurance of switches (for switched socket-outlet) (6)
15. Mechanical strength test (6)
16. Heat Resistance test (7)
17. Resistance to abnormal heat and fire test (8)
18. Resistance to ageing and humidity tests (11)
18.1 Resistance to humidity test (11)
18.2 Resistance to ageing test (11)
19. Resistance to excessive residual stresses and to rusting test (12)
Figures (13)
METHODS OF TESTING FOR PLUGS AND
SOCKET OUTLETS FOR VOLTAGES UP TO 220 V
FOR HOUSEHOLD AND SIMILAR GENERAL USE
1-SCOPE
This standard is concerned with methods of testing plugs socket-outlets and
socket-outlet adapters for use in residential buildings and the like, rated at
127V, 15 AMP and 220V, 13 AMP.
2-SUPPLEMENTARY REFERENCES
Saudi Arabian Standard No. …./…. "Plugs and Socket Outlets for voltages up
to 220 V for Household and Similar General Use".
3-REQUIREMENTS
Unless otherwise specified, the tests shall be carried out at room temperature
(23 ± 2)o C and at a relative humidity not exceeding 80%.
4-VISUAL INSPECTION
Plugs, socket-outlets and socket-outlet adaptors, shall be visually inspected to
ensure conformity of materials, construction and marking with the relevant
requirements.
5-MEASUREMENT OF DIMENSIONS
5.1 Plugs, socket-outlet and socket-outlet adaptors shall be tested for
interchangeability.
5.2 The dimensions of plug pins and spacing between socket contacts, shall be
checked by means suitable gauges. However, if gauges are not available,
measurement of dimensions shall be made by means of suitable measuring
devices readable to 0.01 mm.
5.3 The clearance and creepage distances shall be measured between the following
parts:
5.3.1 Live parts of different polarity.
5.3.2 Live parts and accessible metallic parts.
5.3.3 Live parts and earth (when the socket -outlet is correctly mounted and
connected as for service).
5.3.4 Live metallic parts and the enclosure or the service on which the socket -outlet
is mounted.
6-INSULATION RESISTANCE TEST
6.1 The insulation resistance for plugs, socket-outlets and socket-outlet adaptors,
shall be measured by applying a D.C. Voltage of 500V, for a period of one
minute, between the following pats:
- Current carrying terminals.
- Current carrying terminals connected together and any other parts insulated there from including earthing terminals.
6.2 The insulation resistance measured shall be not less than 5 megohms. For
resilient and non-rewireable plugs the insulation resistance shall not be less than
50 megohms. insulation resistance shall not be less than 2 megohms across the
switch contacts with switch open, where applicable.
7-ELECTRIC STRENGHT TEST
7.1 A high voltage of substantially sine-wave form, shall be applied between the
following parts of the plugs, socket-outlets and socket-outlet adaptors.
Initially, no more than half the prescribed voltage shall be applied, then it shall
be raised gradually to the full value and maintained for one minute:
- Between current carrying terminals.
- Between current carrying terminals connected together and any other parts insulated there from including earthing terminals.
The voltage value shall be 2000 ±± 60 V. having a frequency of 50 or 60 Hz if
applied to 250 V plugs, socket-outlet and socket-outlets adaptors, and 1500 V
having a frequency of 60 Hz if applied to plugs and socket-outlets of 127V.
7.2 Any flashover or breakdown of insulation shall be recorded. Glow discharges
without drop in voltage are ignored.
7.3 Each switched socket-outlet shall also pass a momentary high voltage of 750V
r.m.s applied across each break with the switch open without any flashover or
breakdown of insulation.
8-WITHDRAWAL FORCE TEST
For socket-outlet and socket-outlet adaptors.
8.1 The socket-outlet and the socket-outlet adaptors shall be mounted as in normal
use.
8.2 A suitable test plug shall be correctly inserted into the corresponding socket-
outlet contacts.
8.3 A tensile force shall be gradually applied to the test plug in a direction to pull it
straight out and the value of the force, when the plug is just pulled out, shall be
measured.
8.4 The withdrawal force shall be measured 3 times consecutively on the same
socket-outlet and the average taken.
8.5 The average value shall conform with Table-1.
Table 1
Withdrawal force
Rating Number of Poles Force in Newtons
Max. Min.
15A/127V 2 50 8
15A/127V 3 54 9
13A/220V 2 50 8
13A/220V 3 54 9
9-CONTACT RESISTANCE TEST
9.1 A current derived from an a.c. source having a no load voltage not exceeding
12 V, and equal to 1.5 times rated current or 25 A, whichever is the greater,
shall be passed between:
- The earthing pin of a plug and the earthing terminal of a socket outlet or the earthing pin of a socket-outlet adaptor.
- The earthing terminal of a socket-outlet and each accessible metallic part.
9.2 The voltage drop between the earthing terminal and the accessible metallic part
shall be measured, and the resistance shall be calculated from the current and
this voltage drop. Care should be taken that the contact resistance between the
tip of the measuring probe and the metallic part under test does not influence
the test results.
9.3 The value of the resistance shall not exceed 0.05 ohm.
10-TEMPERATURE RISE TEST
10.1 The temperature rise of the terminals of a plug and current carrying parts of a
socket outlet and a socket outlet adaptor, shall be measured using suitable
thermocouples attached to current carrying parts by low melting point alloy or
by some other equally effective means of attachment.
10.2 The plug socket-outlet and socket-outlet adaptor, shall carry their rated current
at the rated voltage + 10% & - 20%. The temperature of the current carrying
parts shall be measured after a time has elapsed sufficient for the temperature to
become steady (stability being taken as less than 1°C rise within one hour). 10.3 The temperature rise of the current carrying parts shall be calculated.
10.4 The temperature rise shall not exceed 45 K.
11-CURRENT BREAKING CAPACITY OF SOCKET-CONTACTS
11.1 Socket-outlet shall be mounted and connected for tests as they are normally to
be mounted and connected in service, including the earthing connection. The
test circuit shall be a non-inductive a.c. circuit.
11.2 The plug shall be inserted into the corresponding socket-outlet and a current
130% of the rated value at rated voltage shall be passed.
11.3 The plug shall be fully inserted, and immediately withdrawn at a speed of
approximately 15cm/s from the socket-outlet, 10 times in succession at
intervals of 30s.
11.4 During the test, no sustained arcing shall occur, and after the test no damage
shall be evident.
11.5 The high voltage shall be applied as (specified in item 7), to the plug and the
socket-outlet and any flashover or breakdown in insulation shall be recorded.
12-CURRENT BREAKING CAPACITY OF SWITCHES
(For switched socket-outlet):
12.1 Switched socket-outlet shall be mounted and connected for test as they are
normally to be mounted and connected in service. The test circuit shall be a
non-inductive a.c. circuit at 110% of the rated voltage. The test current shall be
adjusted to 130% of the rated value.
12.2 The switch of the socket-outlet shall be operated so as to make and break the
test current 10 times in succession at intervals of 30s.
12.3 The insulation resistance of the socket-outlet shall be measured as specified in
item 6.
12.4 The high voltage shall be applied (as specified in item 7) to the socket outlet
and any flashover or breakdown in insulation shall be recorded.
13-ELECTRICAL ENDURANCE OF SOCKET-CONTACTS
13.1 Socket-outlets shall be tested for capacity to make and break the rated current at
the rated voltage, by insertion, and immediate withdrawal of a plug, 15000
times (30000 movements) in a non-inductive a.c. circuit, at a rate of six
insertions and six withdrawals per minute. The speed of travel of the plug being
approximately 15cm/s. The plug shall be renewed after each 5000 insertions
and withdrawals (10000 movements). For the purpose of this test, no
lubrication is applied to the plug or socket under test.
13.2 After the test, the socket-outlet shall be checked to detect any wear impairing its
operation and any appreciable damage to the openings in the cover provided for
the plug pins. The shutter shall be checked to detect any malfunction or defect
in shielding of the socket-outlet.
13.3 The insulation resistance of the socket-outlet shall be measured as specified in
item 6.
13.4 The high voltage shall be applied (as specified in item 7) to the socket-outlet
and any flashover or breakdown in insulation shall be recorded.
14-ELECTRICAL ENDURANCE OF SWITCHES
(For switched socket-outlet).
14.1 Switches shall be tested for capacity to make and break the rated current at
rated voltage, in a non-inductive a.c. circuit, 15000 times (30000 movements) at
a rate not exceeding six complete cycles per minute at regular intervals. The
periods during which the switches are ON and OFF shall be approximately
equal.
14.2 In order to facilitate inspection, the switched socket-outlet plates need not be in
position after the first 4000 operations. Metallic switched socket-outlet plates
and all non-current carrying metallic parts that are normally exposed when the
switched socket-outlet plate is not in position and that may become live in the
event of failure of insulation shall be connected to the earthed pole of the test
circuit. The connection to earth may be through a fine wire fuse. The means
used for operating the switch shall be such as to move the actuating member at
a speed of approximately 30 cm/s both in making and breaking the circuit, and
shall be so positioned that the normal action of the mechanism as a whole is not
interfered with, in any way.
14.3 After the test, the switches shall be checked to detect any malfunction and the
insulation resistance shall be measured as specified in item 6.
14.4 The high voltage shall be applied (as specified in item 7) to the socket-outlet
and any flashover or breakdown in insulation shall be recorded.
14.5 At the end of the test, the switches shall be checked to determine whether they
are still in a serviceable condition.
15-MECHANICAL STRENGTH TEST
15.1 Any decorative cover or parts not providing protection against electric shock,
shall be removed.
15.2 Plugs: Non-rewireable plugs are tested as delivered.. Rewireable plugs. are
fitted with 3-core PVC 1.25 mm2 flexible cord. The flexible cords attached to
plugs are cut to a length of 120 ± 5mm.
Plugs are tested in the tumbling barrel shown in Fig (1) falling 500 mm on to a
plywood base 10mm thick. The barrel is turned at a rate of 5 r/min, 10 falls per
minute thus taking place.
Only one plug is tested at a time, the number of drops is as follows:
plugs 2500
- Non-rewireable
plugs 1000
- Rewireable
15.3 After the test the plug shall have no external damage which might affect the
safety and no components shall become detached.
15.4 Socket-outlets are tested with the impact test apparatus shown in Fig. (2-a). The
pendulum consists of a steel tube suspended in such a way that it swings only in
a vertical plane. A hammer of 0.15 kg is rigidly fixed to the lower end with its
axis 1 m from the axis of suspension.
The striking element is hemispherical face made of polyamide having a
Rockwell hardness of HR 100 and a radius of 10 mm Fig. (2-b). The design of
the apparatus is such that a force of between 1.9 N and 2 N has to be applied to
the face of the hammer to maintain the pendulum in a horizontal position . The
socket-outlet is mounted on a sheet of plywood 8 mm thick and 175 mm square
secured at its top and bottom edges to a mounting support. having a mass of
10± 1Kg. is mounted on a rigid bracket by means of pivots. The bracket is
mounted on a frame which is fixed to a solid wall, See Fig. (2-c).
The design of the mounting assembly shall be such that:
- The sample can be so placed that the point of impact lies in the vertical plane through the axis of the pivot of the pendulum.
- The sample can be moved horizontally and turned about an axis perpendicular to the surface of the plywood.
- The plywood can be turned about a vertical axis.
The socket-outlet is mounted on the plywood as in normal use. The socket-
outlet is placed so that the point of impact lies in the vertical plane through the
axis of the pivot of the pendulum. For all tests, the hammer falls from a height
of 150 mm measured vertically between the point of impact on the sample and
the face of the hammer at the point of release. Ten blows are applied to points
evenly distributed over the socket-outlet.
15.5 After the test the socket-outlet shall still be in accordance with the (creepage
and clearance distances, Insulation resistance and Electric strength
requirements).
16-HEAT RESISTANCE TEST
16.1 Plugs, socket-outlet and socket-outlet adaptors, shall be heated in a
thermostatically controlled oven. The used oven in the test shall be capable of
holding the temperature of the air surrounding the test samples within
(100 ± 2)o C and shall be such as to prevent the samples from being raised to a
temperature above that specified.
16.2 The temperature of the oven shall in advance, be adjusted to the test
temperature, and then the samples shall be inserted.
16.3 The samples shall be kept for a period of one hour inside the oven and then
taken out and allowed to cool to room temperature naturally.
16.4 After the test, there shall be no marked deformation, softening or other defects
in the samples, which any impair their safety.
16.5 All other parts of insulating material shall be subjected to the ball pressure test
using the apparatus shown in Figure 3.
16.5.1 The surface of the part to be tested is placed in the horizontal position and a
steel ball of 5 mm diameter is pressed against this surface with a force of 20 N.
16.5.2 The test is made in a heating cabinet at a temperature of 125±2o C.
After 1 h, the ball is removed from the sample which is then cooled down
within 10s to approximately room temperature by immersion in cold water. 16.5.3 The diameter of the impression caused by the ball is measured and shall not
exceed 2 mm.
17-RESISTANCE TO ABNORMAL HEAT AND FIRE
Glow wire test shall be carried out as follows:
Notes: 1- The tests shall not be made on parts of ceramic material or metal.
2- Small parts unlikely to be subjected to abnormal heat and whose failure to pass these tests would not materially affect the safety of the unit are not subjected to the
test.
17.1 Description of test apparatus
17.1.1 The glow-wire consists of a specified loop of a nickel/chromium (80/20) wire 4
mm in diameter; when forming the loop, care must be taken to avoid fine
cracking at the tip.
17.1.2 A sheathed fine-wire thermocouple, having an overall diameter of 0.5 mm and
wires of NiCr and NiA1 with the welded point located inside the sheath, is used
for measuring the temperature of the glow-wire.
17.1.3 The glow-wire, with the thermocouple, is shown in figure 4.
17.1.4 The sheath consists of a metal resistant to a temperature of at least 960o C. The
thermocouple is arranged in a pocket hole, 0.6 mm in diameter, drilled in the tip
of the glow-wire, as shown in detail Z of Figure 4. The thermovoltages shall
comply with the temperatures indicated in table 2. The cold connection shall be
kept in melting ice unless a reliable reference temperature is obtained by other
means, for example by a compensation box.
17.1.5 The instrument for measuring the thermovoltage should be accurate to 1%.
17.1.6 The glow-wire is electrically heated; the current necessary for heating the tip to
a temperature of 960o C is between 120 A and 150 A.
17.1.7 The test apparatus shall be so designed that the glow-wire is kept in a horizontal
plane and that it applies a force of 0.8 N to 1.2 N to the specimen, the force
being maintained at this value when the glow-wire or the specimen is moved
horizontally one towards the other over a distance of at least 7 mm.
An example of the test apparatus is shown in Figure 5.
17.1.8 To evaluate the possibility of spread of fire, for example by burning or glowing
particles falling from the specimen, a layer of the material or components
normally surrounding or situated underneath the specimen is placed underneath
the specimen at a distance equal to the distance between the specimen and the
surrounding material or components when the specimen is mounted as in
normal use.
17.2 Calibration of the thermocouple
The calibration of the thermocouple shall be carried out at the temperature
960o C using as standard method a foil of silver, 99.8% pure, 2 mm square and
0.06 mm thick, placed on the upper face of the tip of the glow-wire. The glow-
wire is heated and a temperature of 960o C is reached when the silver foil melts.
17.3 Preconditioning
If not otherwise specified in the relevant specification, the specimen is stored
for 24 h in an atmosphere having a temperature between 15o C and 35o C and a
relative humidity between 45% and 75%.
17.4 Initial
measurements
The specimen shall be examined visually and, when specified in the relevant
specification, the physical/electrical parameters measured.
procedure
17.5 Test
note
Warning
Precautions must be taken to safeguard the health of personnel conducting tests
against:
- the risks of explosion or fire;
- the inhalation of smoke and/or toxic products;
- the toxic residues.
17.5.1 The specimen is arranged so that:
- the surface in contact with the tip of the glow-wire is vertical;
- the tip of the glow-wire is applied to the part of the surface of the specimen which is likely to be subjected to thermal stresses in normal use.
The tip of the glow-wire is applied at a place where the section is thinnest,
but preferably not less than 15 mm from the upper edge of the specimen.
If possible the tip of the glow-wire is applied to flat surfaces and not to
grooves, knock-outs, narrow recesses or sharp edges.
17.5.2 The glow-wire is electrically heated to the temperature given in table 2, which
is measured by means of the calibrated thermocouple. Care must be taken to
ensure that, before starting the test, this temperature and the heating current are
constant for a period of at least 60 s and that heat radiation does not influence
the specimen during this period or during the calibration, for example by
providing an adequate distance or by using an appropriate screen.
17.5.3 The tip of the glow-wire is then brought into contact with the specimen for
30 ± 1 s. The heating current is maintained during this period. After this
period, the glow-wire and specimen are slowly separated, avoiding any further
heating of the specimen and any movement of air which might affect the result
of the test.
The movement of the tip of the glow-wire into the specimen when pressed to it
shall be mechanically limited to 7 mm.
17.5.4 If not otherwise specified by the relevant specification, the test is made on one
specimen. In the case of doubt with regard to the results of the test, the test is
repeated on two further specimens.
Before each test, it is necessary to clean the tip of the glow-wire of any residue
of previously tested material, for example by means of a brush.
Table 2. Application of glow-wire test
Part Temperature of glow-wire
o C
- Parts necessary to retain live parts in
850 ± 15
position
- Parts not necessary to retain live parts in
650 ± 10
position (although they may be in contact
with live parts)
17.6 The test specimen shall be either a complete unit or, if the test cannot be made
on a complete unit, a suitable part may be cut from one for the purpose of the
test. The test is made on one specimen.
In case of doubt, the test shall be repeated on two further specimens.
The test shall be made, applying the glow wire once.
The specimen shall be positioned during the test in the most unfavourable
position of its intended use (with the surface tested in a vertical position).
The tip of the glow wire shall be applied to the specified surface of the
specimen taking into account the conditions of the intended use under which a
heated or glowing element may come into contact with the specimen.
17.7 The specimen shall be regarded as having passed the glow wire test if:
a) there is no visible flame and no sustained glowing; or
b) flames and glowing at the specimen extinguish within 30 s after the
removal of the glow wire.
There shall be no ignition of the tissue paper or scorching of the board.
18-RESISTANCE TO AGEING AND HUMIDITY TESTS
18.1 Resistance to humidity test
18.1.1 A convenient temperature (T o C) between 20o C and 30o C shall be chosen as a
reference temperature. Each unit shall be brought to a temperature of between
T o C and (T+4)o C. then it shall be placed in a humid cabinet maintained between
91% and 95%.
The temperature of the air at all positions within the cabinet where the units can
be placed shall be kept within 1o C of the chosen value.
18.1.2 The unit shall be left in the cabinet for 48 hours.
18.1.3 Immediately after the humidity treatment, the insulation resistance shall be
measured as specified in clause 6.
18.1.4 The value of insulation resistance shall not be less than 5 megohms except
across switch contacts with the switch open (where applicable) where it shall be
not less than 2 megohms.
NOTE: A relative humidity of between 91% and 95% can be obtained by placing in the
humidity cabinet a saturated solution of potassium nitrate (KNO3) or sodium sulfate (Na2 S04)
in water having a sufficiently large contact surface with the air.
18.2 Resistance to ageing test
18.2.1 Units are subjected to a test in a heating cabinet with an atmosphere having the
composition and pressure of the ambient air and ventilated by natural
circulation.
The temperature in the cabinet is kept at 70o C ± 5o C.
The specimens are kept in the cabinet for a minimum of 7 days.
18.2.2 After the treatment, the specimens are removed from the cabinet and kept at
normal room temperature and relative humidity for at least 4 h.
18.2.3 The specimens shall show no crack visible with normal or corrected vision
without additional magnification, nor shall the material have become sticky or
greasy, when tested as follows:
With the forefinger wrapped in a dry piece of rough cloth the specimen is
pressed with a force of between 4.9 N and 5.0 N. The force can be obtained in
the following way. The specimen is placed on one of the pans of a balance
and the other pan is loaded with a mass equal to the mass of the specimen plus
500 g. Equilibrium is then restored by pressing the specimen with the forefinger
wrapped in a dry piece of rough cloth.
No traces of the cloth shall remain on the specimen and the material of the
specimen shall not stick to the cloth.
18.2.4 After the test the specimens shall show no damage.
19-RESISTANCE TO EXCESSIVE RESIDUAL STRESSES AND TO RUSTING 19.1 Copper alloy parts shall be checked by the following test:
19.1.1 The specimen is degreased in a suitable alkaline degreasing solution or organic
solvent, then immersed in an aqueous solution of mercurous nitrate containing
10 g of Hg2(NO3)2 and 10 ml of HNO3 (relative density 1.42) per litre of
solution for 30 min ± 1 min at a temperature of 20o C ± 5o C.
NOTE: Attention is drawn to the fact that due precautions should be taken when using these
liquids as they are toxic.
19.1.2 After the treatment, the specimen is washed in running water, any excess
mercury is wiped off, and the specimen is immediately visually examined.
There shall be no cracks visible with normal or corrected vision without
additional magnification.
19.2 Ferrous parts shall be checked by the following test:
19.2.1 The specimen is degreased in a suitable alkaline degreasing solution or organic
solvent, the parts are then immersed for 10 min ± 0.5 min in a 10% solution of
ammonium chloride in water at a temperature of 20o C ± 5o C.
19.2.2 Without drying but after shaking off any drops, the parts are placed for 10 min
± 0.5 min in a box containing air saturated with moisture at a temperature of
20o C ± 5o C.
19.2.3 After the parts have been dried for at least 10 min in a heating cabinet at a
temperature of 100o C ± 5o C their surfaces shall show no signs of rust.
NOTE 1: Traces of rust on sharp edges and any yellowish film removable by rubbing should
be ignored.
13
Note: This drawing is not intended to govern design except as regards the dimensions and specific requirements shown.
All dimensions are in millimeters.
Figure 1. Tumbling barrel
SAUDI ARABIAN STANDARD SASO 443/2003
Materials
1: Polyamide or horn beam 2, 3, 4 and 5 : Steel
(b) Constructional details of striking element
NOTE: The drawing is not intended to govern design except as regards the dimensions and specific requirements shown.
Figure 2 Pendulum impact test apparatus
(c) Constructional details of mounting support for test samples.
NOTE: This drawing is not intended to govern design except as regards the dimensions and specific requirements shown .
All dimensions are in millimeters.
Figure 2 (concluded)
Figure 3 – Apparatus for ball pressure test
Figure 4 - Glow-wire and position of the thermocouple
Figure 5 - Test apparatus (example)
OSPF邻居明文认证配置 【实验名称】 OSPF 邻居明文认证配置 【实验目的】 掌握OSPF 的邻居明文认证配置。 【背景描述】 你是一名高级技术支持工程师,某企业的网络整个的网络环境是ospf。为了安全起见,新加入的路由器要通过认证,请你给予支持。 【实现功能】 完成OSPF区域新成员加入的安全认证。 【实验拓扑】 【实验设备】 R2624路由器(2台)、V35DCE(1根)、V35DTE(1根) 【实验步骤】
第一步:基本配置 Red-Giant>en Red-Giant#conf t Red-Giant(config)#hostname R1 !更改路由器主机名 R1(config)#int s0 R1(config-if)#ip add 192.168.12.1 255.255.255.0 !为接口配置地址 R1(config-if)#clock rate 64000 ! 设置时钟速率在DTE端不用设置 R1(config-if)#no sh R1(config)#iint loo 0 R1(config-if)#ip add 1.1.1.1 255.255.255.0 ! 配置loopback接口,保证路由更新的稳定Red-Giant>en Red-Giant#conf t Red-Giant(config)#hostname R2 R2(config)#int s0 R2(config-if)#ip add 192.168.12.2 255.255.255.0 R2(config-if)#no sh R2(config)#int loo 0 R2(config-if)#ip add 2.2.2.2 255.255.255.0 ! 配置loopback接口,保证路由更新的稳定 验证测试:ping R2#ping 192.168.12.1 Sending 5, 100-byte ICMP Echoes to 192.168.12.1, timeout is 2 seconds: !!!!! 第二步:启动OSPF路由协议 R1(config)#router os 1 R1(config-router)#net 192.168.12.0 0.0.0.255 area 0 R1(config-router)# net 1.1.1.0 0 0.0.0.255 area 2 R1(config-router)#end R2(config)#router os 1 R2(config-router)#net 192.168.12.0 0.0.0.255 area 0 R2(config-router)#net 2.2.2. 0 0.0.0.255 area 1 R2(config-router)#end 验证测试:R1# sh ip os nei (以R1为例) Neighbor ID Pri State Dead Time Address Interface 2.2.2.2 1 FULL/ - 00:00:37 192.168.12.2 Serial0 第三步:配置OSPF验证 R1(config)#router os 1 R1(config-router)# area 0 authentication !配置区域间明文验证 R1(config)#int s0 R1(config-if)# ip os authentication-key star !配置验证密码 R2(config)#router os 1
立体商标是什么与立体商标审查标准立体商标由具有显著特征的其他标志与不具有显著特征的三维标志组合而成,其他标志与平面商标具有显著特征的部分相同或近似,易使相关公众对商品或服务的来源产生误认,判为相同或近似商标。 一、法律依据 《商标法》第八条任何能够将自然人、法人或者其他组织的商品与他人的商品区别开的可视性标志,包括文字、图形、字母、数字、三维标志和颜色组合,以及上述要素的组合,均可以作为商标申请注册。 《商标法》第十二条以三维标志申请注册商标的,仅由商品自身的性质产生的形状、为获得技术效果而需有的商品形状或者使商品具有实质性价值的形状,不得注册。 二、相关解释 立体商标,是指由三维标志或者含有其他标志的三维标志构成的商标。立体商标可以是商品本身的形状、商品的包装物或者其他三维标志。 本部分规定立体商标注册申请的形式审查和实质审查,其中实质审查包括立体商标不得违反《商标法》第十二条的审查、立体商标的显著特征的审查和立体商标相同、近似的审查。 立体商标不得违反《商标法》第十条规定的审查适用本标准第一部分的规定。 三、立体商标的形式审查 (一)申请注册立体商标的,申请人应当在申请书中予以声明。未声明的,视为平面商标。
(二)申请注册立体商标的,申请人应当提交能够确定三维形状的商标图样。需要提交多视图的,应当放在同一张商标图样中,且最多不得超过6幅。商标图样的长或者宽不得大于10厘米,不小于5厘米。 四、立体商标的实质审查 (一)仅有由商品自身的性质产生的形状 由商品自身的性质产生的形状,是指为实现商品固有的功能和用途所必需采用的或者通常采用的形状。 例如: 指定使用商品:安全扣 (二)仅有为获得技术效果而需有的商品形状 为获得技术效果而需有的商品形状,是指为使商品具备特定的功能,或者使商品固有的功能更容易地实现所必需使用的形状。 例如: 指定使用商品:电源插头
竭诚为您提供优质文档/双击可除 saso认证模板 篇一:saso认证需要注意的事项及认证流程 saso认证需要注意的事项及认证流程 一、注意事项 saso标准中有很多是在相关的国际电工委员会(iec) 等国际组织的的安全标准基础上建立的。像很多其他的国家一样,沙特阿拉伯根据自己国家的民用及工业电压,地理及气候环境,民族宗教习惯等在标准中添加了一些特有的项目。为了实现保护消费者的目的,saso标准不只针对从国外进口的产品,对于在沙特阿拉伯本土生产的产品也同样适用。沙特阿拉伯工业及商务部及saso要求所有saso认证标准包含的产品在进入沙特海关时有saso认证证书。没有saso证书的产品会被沙特港口海关拒绝入境。 根据沙特阿拉伯标准组织的规定,saso认证包含所有成人及儿童在住所,办公或娱乐场所使用的产品,所有机动车及零配件,以及建筑产品。这些产品主要可以分为以下类别:空调saso、电池saso、化妆品saso、玩具saso、压缩机saso、风扇saso、家用电器saso、电线电缆saso、传真机saso、
灯具saso、光电源saso、电梯saso、发电机saso、办公用电子电器设备saso、个人电脑saso、电源saso、汽车配件saso、陶瓷saso、音响saso、功放机saso、会议系统saso、调音台saso 沙特各城市都采用较低电压,分为127伏和220伏(利雅德为235伏)两种,皆为60赫兹;但在麦加及工业区系采用较高电压,有220伏及380伏两种,亦为60赫兹.一般家庭及办公室同时备有110伏(即指127伏)及220伏两种电插座以供不同电压的电器产品使用,一般而言,冷气机、洗衣机多用220伏,小家电多用110伏。 二、认证流程 产品出口沙特有两种形式一种是批次申请一种是注册形式。下面介绍批次申请saso认证流程: (saso认证)批次检验的程序 1、质量文件审核 请递交以下文件: ◆测试报告(有资质的第三方实验室出具),或 ◆制造商/工厂质量体系认证证书和内部测试报告/质量证明文件 2、装船前检验 ◆请递交以下申请文件: 检验申请表(Requestforcertificate/Rfc)符合性声
OSPF(Open Shortest Path First开放式最短路径优先)是一个内部网关协议::AS内部路由(本质区别),采用链路状态路由选路技术 开放式最短路径优先协议是一种为IP网络开发的内部网关路由选择协议其由三个子协议组成hello协议,交换协议,扩散协议,其中hello协议负责检查链路是否可用并完成指定路由 器和备份路由器;交换协议完成“主”,“从”路由器的选择和交换各自的路由数据库信息,扩散协议负责完成各路由器中路由数据库的同步维护 不同厂商管理距离不同,思科OSPF的协议管理距离(AD)是110,华为OSPF的协议管理距离是10。 OSPF 采用链路状态路由选择技术,开放最短路径优先算法 路由器互相发送直接相连的链路信息和它拥有的到其它路由器的链路信息。每个 OSPF 路由器维护相同自治系统拓扑结构的数据库。从这个数据库里,构造出最短路径树来计算出 路由表。当拓扑结构发生变化时, OSPF 能迅速重新计算出路径,而只产生少量的路由协议流量。 此外,所有 OSPF 路由选择协议的交换都是经过身份验证的。 主要优点 收敛速度快;没有跳数限制; 支持服务类型选路 提供负载均衡和身份认证 适用环境 规模庞大、环境复杂的互联网 OSPF协议的优点: OSPF能够在自己的链路状态数据库内表示整个网络,这极大地减少了收敛时间,并且支持大型异构网络的互联,提供了一个异构网络间通过同一种协议交换网络信息的途径,并且不容易 出现错误的路由信息。 OSPF支持通往相同目的的多重路径。 OSPF使用路由标签区分不同的外部路由。 OSPF支持路由验证,只有互相通过路由验证的路由器之间才能交换路由信息;并且可以对不同的区域定义不同的验证方式,从而提高了网络的安全性。 OSPF支持费用相同的多条链路上的负载均衡。 OSPF是一个非族类路由协议,路由信息不受跳数的限制,减少了因分级路由带来的子网分离问题。 OSPF支持VLSM和非族类路由查表,有利于网络地址的有效管理 OSPF使用AREA对网络进行分层,减少了协议对CPU处理时间 BGP(边界网关协议):AS外部路由,采用距离向量路由选择 BGP是唯一一个用来处理像因特网大小的网络协议,也是唯一能够妥善处理好不相关路由域间的多路连接协议。BGPv4是一种外部的路由协议。可认为是一种高级的距离向量路由协议
关于商标,除了有我们常见的服务商标、文字商标、图形商标外,还有立体商标(即:三维商标),是以本身固有的形态而申请的商标。下面来详细介绍立体商标的分类。 立体商标,顾名思义,是指由三维标志或者含有其它标志的三维标志构成的商标。它可以是商品本身的形状、包装物或其他三维标志。申请人在申请注册立体商标时必须在申请书中予以声明,否则视为平面商标。 立体商标的分类 立体商标按照构成的不同,有四种表现形式: 1、与商品无关的装饰性立体外形。 这类立体商标主要是用于装饰商品,来向消费者传达商品,起到认牌功能的作用。 比如"奔驰"车的标记是一个环,中间是一个三角星,这个东西本身并不是汽车上的一个零部件,与车本身没有任何关系,只是用来说明这辆车是奔驰车。 再如“劳斯莱斯”车上的“欢乐女神”,当初是安放在劳斯莱斯引擎盖前端的的吉祥物,后来成为了劳斯莱斯标志性的装饰物。 2、商品本身的立体外形
这种以商品本身立体外形来注册的立体商标在食品中很常见,往往是需要工艺的打造,成品的外形设计。 比如饼干:在欧盟有一家食品生产商就生产一种三角形、网状的饼干,这种饼干的形状就被欧盟内部市场协调局核准注册为立体商标。 再如“费列罗”就把自己的商品本身注册成了立体商标,其独特的外观具有充分的显著性,是可以作为立体商标进行注册的。 3、商品包装物的外形 比如"酒鬼"的酒瓶是一个麻袋装满了烧陶器的泥巴,拿到窑里烧,麻袋烧掉了,剩下的泥巴烧成陶器的形状,这个酒瓶子的形状是一个很特殊的酒的包装物外型,可以成为另一种立体商标。 4、带有文字或图形商标成分的商品立体形状 (1)商品自身的立体形状附带的文字商标或图形商标; (2)商品包装或容器的立体形状上附带的文字商标或者图形商标; (3)商品广告物的立体形状上附带的文字或者图形商标。
SASO 2204 家用或者类似通用127伏插头和插座ICS: SASO董事会的批准日期 正式公告的发布日期 本标准的执行日期
目录 细目页码 1.应用范围和领域 2 2.补充参考 2 3.定义 2 4.材质、设计、构造 2 5.额定值和特征 5 6.抽样7 7.测试7 8.技术合格标准8 9.标记8 附注10
家用或者类似通用127伏插头和插座 1.应用范围和标准 本标准是有关插头、插座的标准,插座主要用于住宅以及类似以下级别 15安/127伏(相对中性点电压)用于127伏交流电路。 2. 补充参考 本标准须通过SASO有关“家用或者相似通用插头插座的测试方法”的要求。 3. 定义 3.1 额定电流 在未超出许可温升的情况下,额定电流为厂方指定的插头或插座可持续携带的电 流。 3.2 额定电压 额定电压为厂方指定的有关插头、插座最高可持续正常运行的电压。 3.3 插头 插头为一种有两个或者三个金属插脚用于接触相应插座以及接有软电线或电缆的 设备。 3.4 插座 一种有两个或者三个金属节点用于接触相应插头插脚的以及连接到固定布线上的 设备。当插头与插座没有接触时,插座应该配有自动屏蔽带电插头节点的保护门。 3.5 安全插头 一种在线性插脚与其端子之间电路有熔断丝的插头。 3.6 弹性插头 一种底座、外壳或者这些组件中都是橡胶或者其他合适的弹性材料的插头。 3.7 不可再接线插头 一种与软电线形成结构性部件,在除非永久功能失效的情况下与弹性软电线不可分 离的插头。 3.8 开关插座 一种与单级开关相连的插座。 3.9 插脚 平整或者U型平截面的金属部件。 3.10 端子 通过一个螺丝钉在一个孔或者槽中固定导体的金属部件。 4.材质、设计和结构 在插头、插座中应该满足以下要求
认证是由第三方经授权的独立的权威机构根据相关的国家或国际法规标准,对生产厂家的产品或生产体系进行检测与监督,并就通过与否签发检测报告与证书的过程。如果取得认证,也就说明产品质量符合了国家或国际标准。 UL认证(美国):保险实验室认证标志。进入美国的货物,很多都需要有UL标志。 UL是英文保险商试验所(Underwriter Laboratories Inc.)的简写,UL安全试验所是美国最有权威的,也是界上从事安全试验和鉴定的较大的民间机构。它是一个独立的、非营利的、为公共安全做试验的专业机构。它采用科学的测试方法来研究确定各种材料、装置、产品、设备、建筑等对生命、财产有无危害和危害的程度;确定、编写、发行相应的标准和有助于减少及防止造成生命财产受到损失的资料,同时开展实情调研业务。总之,它主要从事产品的安全认证和经营安全证明业务,其最终目的是为市场得到具有相当安全水准的商品,为人身健康和财产安全得到保证作出贡献。目前,UL在美国本土有五个实验室,总部设在芝加哥北部的Northbrook镇,同时在台湾和香港分别设立了相应的实验室。 CE认证(欧盟): “CE”标志是一种安全认证标志,被视为制造商打开并进入欧洲市场的护照。凡是贴有“CE”标志的产品就可在欧盟各成员国内销售,无须符合每个成员国的要求,从而实现了商品在欧盟成员国范围内的自由流通。 在欧盟市场“CE”标志属强制性认证标志,不论是欧盟内部企业生产的产品,还是其他国家生产的产品,要想在欧盟市场上自由流通,就必须加贴“CE”标志,以表明产品符合欧盟《技术协调与标准化新方法》指令的基本要求。 CE两字,是从法语“Communate Europpene”缩写而成,是欧洲共同体的意思。欧洲共同体后来演变成了欧洲联盟(简称欧盟)。CE标志加贴的商品表示其符合安全、卫生、环保和消费者保护等一系列欧洲指令所要表达的要求。 有关CE标志的产品:符合欧盟的有关健康,卫生,安全,环保和消费者保护的等一系列规定。是产品在欧明境内销售的市场准入证明,目前有20多条欧盟指令规定CE涵盖的产品范围及相关的安全要求。 CE标志对贸易和工业产生巨大的影响,符合欧洲标准指令的产品才可贴CE标志。一般而言,欧洲指令的要求适用于最终产品和其它部件的销售。对于绝大多数电子,电器类产品而言,申请CE认证必须符合低电压指令(LVD)和电磁兼容指令(EMC)。 有关指令要求加贴CE标志的工业产品,没有CE标志的,不得上市销售,已加贴CE标志进入市场的产品,发现不符合安全要求的,要责令从市场收回,持续违反指令有关CE标志规定的,将被限制或禁止进入欧盟市场或被迫退出市场。现今执行的指令主要有如下: 低电压指令电磁兼容机械玩具简单压力容器个人护具 衡器活性移植医疗设备燃气设备电讯终端设备防爆设备 VDE认证(德国): VDE是德国国家产品标志。VDE的全称是Prufstelle Testing and Certification Institute,意即德国电气工程师协会。它成立于1920年,是一个国际认可的电子电器及其零部件安全测试及出证机构,是欧洲最有测试经验的试验认证和检查机构之一,也是获欧盟授权的CE公告机构及国际CB组织成员。在欧洲和国际上,得到电工产品方面的CENELEC 欧洲认证体系、CECC电子元器件质量评定的欧洲协调体系、世界性的IEC电工产品、电子元器件认证体系等的认可。评估的产品非常广泛包括家用及商业用途的电器、IT设备、工业和医疗科技设备、组装材料及电子元器件、电线电缆等。 VDE标志主要适用范围为各类电工产品,电子元器件产品等。 VDE是德国著名的测试机构,在电器零部件认证是欧洲最权威的认证。 根据申请按照VDE规范或其他公认的技术标准对电工产品进行试验和认证。因而它向公众提供了一种保护性服务,避免电器在使用时造成危害和产生无线电干扰。 VDE一P的试验和认证特别适用于家用电器、照明器具、手持式工具、娱乐电子设备、医疗电气设备、信息技术设备、安装材料。电线、电缆和电子元器件。VDE—P还对电器所产生的无线电干扰进行测量,在需要时也测量电磁兼容性(EMC)。 GS认证(德国): GS的含义是德语Geprufte Sicherheit(安全性已认证),也有Germany Safety" (德国安全)的意思。GS认证以德国产品安全法(SGS)为依据,按照欧盟统一标准EN或德国工业标准DIN进行检测的一种自愿性认证,是欧洲市场公认的德国安全认证标志。 GS标志表示该产品的使用安全性已经通过公信力的独立机构的测试。GS标志,虽然不是法律强制要求,但是它确实能在 产品发生故障而造成意外事故时,使制造商受到严格的德国(欧洲)产品安全法的约束。所以GS标志是强有力的市场工具,能增强顾客的信心及购买欲望。虽然GS是德国标准,但欧洲绝大多数国家都认同。而且满足GS认证的同时,
OSPF区域详解和3种认证 OSPF的4种特殊区域 1.Stub:过滤LSA4/5,将LS4/5的路由通过LSA3自动下放默认路由,Seed cost=1 注意点:Stub区域所有路由器都要配置成Stub 配置命令在OSPF进程中:area [area ID] stub 2.totally stubby:过滤LSA3/4/5,在ABR上配置 配置命令在OSPF进程中:area [area ID] stub no-summary 3.not-so-stubby:过滤LSA4/5,可以在此区域中出现ASBR,在此区域中,将直接相连的其它AS的路由转换为LSA7,在连接其它OSPF区域的ABR上将LSA7转换为LSA5。远端AS不转换,直接过滤掉(连接其它OSPF区域的ABR上不自动下放默认路由) 配置命令在OSPF进程中: area [area ID] nssa(配置为nssa区域) area [area ID] nssa default-information-originate(下发默认路由) tips: 只要产生LSA5的路由器都是ASBR(ASBR定义) 4.totally-nssa:在not-so-stubby基础上过滤LSA3/4/5,自动下放默认路由 配置命令在OSPF进程中: area [area ID] nssa no-summary 补充命令 area [area ID] nssa no-redistribution default-information-originate 总结no-summary的2个特性,过滤掉外部的LSA3并产生一条内部LSA3的默认路由 OSPF不规则区域互联的3种解决方法 1.ospf多进程的双向重分布 在ABR上启用多个OSPF进程,在每个进程中重分布其它进程的OSPF路由信息 2.Tunnel 在ABR上建立Tunnel口,在Tunnel上配置IP地址 基本配置方法: tunnel source [接口IP地址] tunnel destination [接口IP地址] 在tunnel口中配置一条IP地址 将tunnel口的IP地址在OSPF中宣告 3.Virtual Links 虚链路 area [需要穿越的area ID] virtual-link [对方RID]
实用标准文档三维建模规
城市三维建模是为城市规划、建设、运营、管理和数字城市建设提供技术服务的基础,是城市经济建设和社会发展信息化的基础性工作。城市三维模型数据是城市规划、建设与管理的重要基础资料。为了建设市三维地理信息系统,规市三维建筑模型的制作,统一三维模型制作的技术要求,及时、准确地为城市规划、建设、运营、管理和数字城市建设提供城市建筑三维模型数据,推进城市三维数据的共享,特制定本规。项目软件及数据格式 1、项目中使用的软件统一标准如下: 模型制作软件:3DMAX9 贴图处理软件:Photoshop 平台加载软件:TerraExplorer v6 普通贴图格式:jpg 透明贴图格式:tga 模型格式:MAX、X、XPL2 加载文件格式:shp 平台文件格式:fly 2、模型容及分类 城市建模主要包括建筑物模型和场景模型。 2.1、建筑物模型的容及分类
建筑物模型应包括下列建模容: 各类地上建筑物,包括:建筑主体及其附属设施。含围墙、台阶、门房、牌坊、外墙广告、电梯井、水箱以及踢脚、散水等。 各类地下建筑物,包括:地下室、地下人防工程等。 其他建(构)筑物,包括:纪念碑、塔、亭、交通站厅、特殊公益建(构)筑物以及水利、电力设施等。 全市建筑物模型分为精细模型(精模),中等复杂模型(中模),体块模型(白模)。市全市围主要大街、名胜古迹、标志性建筑等用精模表示,一般建筑物用中模表示,城中村、棚户区等用白模表示。 2.1.1、精细复杂度模型(精模) 2.1.1.1、定义:精细模型为,能准确表现建筑物的几何实体结构,能表现建筑物的诸多细节,对部分重要建筑景观进行重点准确制作表现的模型制作方式。 2.1.1.2、一般制作围:城市中主干道两旁的主要建筑物、主干路十字路口的主要建筑,电信、移动、金融中心大楼,火车站,重点政治、经济、文化、体育中心区建筑,包括标志性建筑物,城市中知名度高的名胜古迹、地标性建筑(如大雁塔、钟楼等)。 2.1.1.3、制作方式:精细制作,不仅能反映实际建筑的大小,整体结构,而且能反映建筑物的细节结构。贴图效果好,带光影效果。用户看上去感觉就是实际的建筑、真实度高。 2.1.2、中等复杂度模型(中模) 2.1.2.1、定义:为了保证大规模数字城市在平台上流畅运行,并能准确表现建筑物的几何实体结构,在不影响建筑物真实性几何结构的基础上,可以忽略部分实体结构,对部分建筑景观进行简单制作表现的模型制作方式。 2.1.2.2、一般制作围:城市中非主干道两旁的主要建筑物、城市临街小区居民楼和其
沙特SASO认证 Created by Sindy Wang
向沙特阿拉伯出口产品的一些常识 ?电压,分为127伏和220伏(利雅德为235伏)两种,皆为60赫兹(麦加及工业区系采用较 高电压,有220伏及380伏两种,亦为60赫兹)。 ?一般家庭及办公室同时备有110伏(即指127伏)及220伏两种电插座以供不同电压的电 器产品使用,一般而言, 冷气机、洗衣机多用220伏,小家电多用110伏. ?禁止向沙特出口的产品(40多个品种): ?武器 ?酒类 ?镇静剂 ?猪肉 ?色情资料 ?酿酒设备 ?烟火 ?圣诞树 ?肉豆蔻 ?面具 ?可视电话 ?表现动物和人的玩具或雕像等
SASO认证介绍 ?SASO是英文Saudi Arabian Standards Organization的缩写,即沙特阿拉伯标准组织。 ?SASO负责为所有的日用品及产品制定国家标准,标准中还涉及度量制度,标识等。 SASO标准中有很多是在相关的国际电工委员会(IEC)等国际组织的安全标准基础上建立的。 ?为了实现保护消费者的目的,SASO标准不只针对从国外进口的产品,对于在沙特阿拉 伯本土生产的产品也同样适用。 ?沙特阿拉伯工业及商务部及SASO要求所有SASO认证标准包含的产品在进入沙特海关 时有SASO认证证书。没有SASO证书的产品会被沙特港口海关拒绝入境。 ?沙特商务部于1995年9月实行国际统一证书程序(ICCP)制,以有利于沙特标准局标准的执 行。 ?所有经SASO批准的手续程序,包括ICCP程序,均符合国际标准组织的指导原则。 ?每批SASO 管制产品进口均须有符合性证明,但并不需在标签上作任何标示。在ICCP 区域发证中心(RLC) 审核并提交所有需要的文件后, 即核发注册证明。 ?SASO 认证包含EMC 的测试内容(自2003 年10 月1 日起,EMC 要求为强制)。 ?SASO 认证不需要进行工厂检查。在出货前三天申请者必须申请当地的RLC 机构进行 产品的出货检验。
电线电缆识别标志第1部分:一般规定GB 6995.1-86 发布时间:1986-11-20 1适用范围 本标准适用于电气装备电线电缆、电力电缆和通信电缆等电缆识别标志及绝缘线芯的识别标志。 2目的 本标准对电线电缆及其绝缘线芯的识别标志方法作出了统一的标准化规定,以保证电线电缆正确连接、安装和安全运行。 3定义 3.1电缆识别标志 用文字、字母、符号、颜色等标记标出电线电缆的制造厂、产品商标、型号、规格、性能等。 3.2绝缘线芯识别标志 用阿拉伯数字、颜色(单一颜色或组合颜色)区分多芯电缆的不同绝缘线芯或标明绝缘线芯的功能。 3.3标准颜色 为识别标志所规定采用的颜色,并用颜色色版表示。 3.4颜色色序 多芯电缆(二芯以上)绝缘线芯采用颜色识别时规定优先采用的颜色(包括组合颜色)及其顺序排列规则。 4一般要求 4.1颜色识别 4.1.1颜色要求 标志颜色应能确认符合或接近GB 6995.2-86《电线电缆识别标志第2部分:标准颜色》规定的某一种颜色。 4.1.2清晰度 标志颜色应易于识别或易于辨认。 4.1.3耐擦性 标志应耐擦,擦试后的颜色应基本保持不变。 4.2数字识别 4.2.1颜色要求 载体应是同一种颜色;所有识别数字的颜色应具有相同颜色。载体颜色与标志颜色应明显不同,且
应能确认符合或接近GB 6995.2—86规定的某一种颜色。 4.2.2清晰度 数字标志应清晰,字迹清楚。 4.2.3耐擦性 数字标志应耐擦,擦试后的标志应仍保持不变。 4.3压印标志 4.3.1型式 压印标志应采用凸印或凹印型式,直接压印在载体上。 4.3.2清晰度 压印标志的字迹应清晰或易于辨认。 4.4标志线或标志带 4.4.1标志线 用于识别电线电缆产地的标志线,应按有关规定申请注册,其颜色可为单一颜色,也可为组合颜色。 4.4.2标志带 标志带是在带子上印上文字、字母、符号等标记,标出电线电缆的制造厂、产品电压等级、型号、规格、商标等等。 4.4.3清晰度 整个标志线上的颜色应保持一致,组合颜色中两种颜色的分界线应保证清晰。标志线的颜色和标志带上的标记应清楚可辨。 4.4.4牢度 用汽油或其他合适溶剂清洗时,标志颜色应保持不变。 5试验方法 5.1标志清晰度用目力检查,当试样表面受到污染不能辨认时,可用汽油或其他合适溶剂浸过的棉织物擦拭试样表面;或者用洁净的刀片切取试样断面进行检查。 5.2标志耐擦性用浸过水的脱指棉或棉布,轻轻擦拭10次,然后用目力检查。
OSPF 配置 Router ospf 进程号 Redistribute 其它路由协议 Network 端口网络反掩码area 区域号 Area 区域号range 网络号掩码 Area 区域号default-cost 花销值 Ip ospf priority number Ip ospf cost 花销值
Show ip ospf database 使用身份验证 为了安全的原因,我们可以在相同OSPF区域的路由器上启用身份验证的功能,只有经过身份验证的同一区域的路由器才能互相通告路由信息。 在默认情况下OSPF不使用区域验证。通过两种方法可启用身份验证功能,纯文本身份验证和消息摘要(md5)身份验证。纯文本身份验证传送的身份验证口令为纯文本,它会被网络探测器确定,所以不安全,不建议使用。而消息摘要(md5)身份验证在传输身份验证口令前,要对口令进行加密,所以一般建议使用此种方法进行身份验证。 使用身份验证时,区域内所有的路由器接口必须使用相同的身份验证方法。为起用身份验证,必须在路由器接口配置模式下,为区域的每个路由器接口配置口令。 任务命令 指定身份验证area area-id authentication 使用纯文本身份验证ip ospf authentication-key password 使用消息摘要(md5)身份验证ip ospf message-digest-key keyid md5 key 以下列举两种验证设置的示例,示例的网络分布及地址分配环境与以上基本配置举例相同,只是在Router1和Router2的区域0上使用了身份验证的功能。: 例1.使用纯文本身份验证 Router1: interface ethernet 0 ip address 192.1.0.129 255.255.255.192
25个立体LOGO设计欣赏 篇一:30个国外优秀Logo设计欣赏及详解 30个国外优秀Logo设计欣赏及详解 拥有一个抢眼的Logo对企业来乃一大幸事,毕竟Logo千千万,但真正让人过目不忘的作品可是屈指可数。好的Logo必须量体裁衣,迅速传递出企业的价值和理念。但Logo不能只是金玉其外,还必须有思想、多功能。比如,可以用标准色在任何尺寸的纸张完美复制和再现。下面就晾出当前30个很杰出的Logo,飨宴大家。 1. Castle Print 一个打印机 品牌 ,该Logo直截了当地体现了了企业的业务性质:利用减色模型,直指其打印行业背景,同时通过色彩的混合塑造出一个与其品牌相符的城堡(Castle)形象。 2. Ryan-Biggs 负空间的运动使得这幅Logo有一种奇幻的效果,完全考验你的空间想象力!B和R两个字母代表了这个品牌,微微的倾斜让整个 设计 看起来更有深度和立体感。色彩搭配极为简单—红色,赋予了Logo 更广的使用范围。 3. One Leaf One Leaf, 顾名思义,即一片树叶。以此为轴线,就呈现出了如此
简洁巧妙的画面。 4. Greener 设计师用粗细不同的灯芯体(San-serif)字体塑造出一种现代感。该Logo不但层次感强,更重要的是可以用单一色调复制重现(这也是评判Logo好坏的重要标准之 一)。 5. Talkmore Talkmore字面意思是“多说点儿”。设计师采用象征的手法,用英文中的单引号分别代替字母“a”和“e”,从而在图形上给予品牌最鲜活的注解。 6. Black Sparrow 看上去很简单的图标,但在细节处理上却达到了极致。从麻雀(即Black Sparrow的中文)的图案到字体,柔和的曲线与平滑的字体相得益彰,将完整的设计融入品牌表现。 7. Swannie Lake 富有时代气息的Avenir字体配合平滑的图案,不但与该Logo完美贴合,而且增添了一许微妙的色彩。 8. Elara Systems
首页>>电子教材>>本章内容 第五章 沉积环境的主要判别标志 第一节 沉积构造标志 一、沉积构造的概念及分类 沉积环境(相)分析:对指示环境的标志进行分析,与沉积环境模式进行比较,从而恢复古代沉积环境的方法。 成因标志:指具有成因意义,能反映其形成环境条件的各种特征。包括沉积岩的颜色、成分、结构、构造、化石、古生态、接触关系、沉积序列(剖面)以及沉积岩体的形态分布等,但概括起来可归属为物理的、化学的、生物的三方面标志。 沉积构造:由沉积物的颜色、成分、结构的不均一性而形成的岩石宏观特征。其规模一般较大,多在野外露头上及岩芯中可直接进行观察和测量。 根据其形成时间划分为:原生沉积构造和次生沉积构造。 根据沉积构造的成因性质可分为三类: 物理成因的沉积构造 化学成因的沉积构造 生物成因的沉积构造 原生沉积构造:沉积物沉积时、沉积后不久、固结前形成的构造。能反映沉积时的沉积介质类型和能量条件。是判别沉积相(沉积环境)的重要标志。 次生沉积构造:在沉积物压实或成岩过程中生成的沉积构造,它反映成岩环境。 物理成因的沉积构造:在流体流动、重力等物理因素作用下而产生的沉积构造(原生)。 化学成因的沉积构造:由结晶、溶解、沉淀等化学作用形成的沉积构造,其中,大多数是在沉积物压实和成岩过程中生成的, 属于次生沉积构造。 生物成因的沉积构造:生物活动或生长而形成的构造(原生)。
二、物理成因的沉积构造 (一)流动构造 是沉积物在搬运和沉积过程中,由于介质的流动而在沉积物表面或内部形成的构造。流动构造是最重要和最常见的沉积构造。 (1)层面构造 在沉积岩的顶面或底面上形成的构造。如:波痕、细流痕、剥离线理、冲刷痕、压刻痕。 1. 波痕 由水流、波浪或风的作用,在沉积物表面形成的波状起伏 痕迹。 (一)流动构造 (1)层面构造 1. 波痕 2. 细流痕 3. 剥离线理 4. 冲刷痕 5. 压刻痕 (2)层理构造 1. 层理构造的术语 2. 层理构造的类型 (3)再作用面构造 (二)准同生变形构造 (三)暴露构造 波痕形态要素 脊点(C, D):最高点 谷点(A, B):最低点 向流面:面向流动方向的缓倾斜面 背流面:背向流动方向的陡倾斜面 波长(L):相邻的两个脊点之间的水平距离 波高(H):波痕的脊点与谷点之间的垂直距离 波痕指数(RI):波长与波高之比(L/H) 对称指数(RSI):向流面水平投影长度与背流面水平投影长度之比(L1/L2) 波痕的内部构造及形成机理及实例 首页>>电子教材>>本章内容
SASO认证包含所有成人及儿童在住所,办公或娱乐场所使用的产品,所有机动车及零配件,以及建筑产品。下面由沙特saso可以代理认证的港易质量认证公司为您介绍下沙特saso认证的相关内容,希望能带来帮助。 沙特阿拉伯工业及商务部及SASO要求所有SASO认证标准包含的产品在进入沙特海关时有SASO认证证书。没有SASO证书的产品会被沙特港口海关拒绝入境。SASO 认证流程及费用有:申请SASO认证流程: 1. 提交箱单、发票,申请表,产品检测报告,产品的照片。 2. 对认证资料进行审核。 3. 审核资料符合要求,会派检验员上门进行装船前检验。如果资料不符合SASO要求,我司会对此提出修改,并协助企业完成符 合SASO要求,再派检验员上工厂进行装船前检验。(可做免验货)
4. 整理验货报告,出具证书草稿件,由企业核实检查证书信息完整及正确。 5. 出具证书正本,并快递给企业证书及发票。 港易质量认证公司专业办理,以最短的周期做最权威的沙特SASO认证,以确保您的产品出口沙特能够顺利清关,被国外客户认可产品的质量。 在唛头、标签、铭牌要求有: 1.所有信息都以英文或阿拉伯文,或者阿拉伯文以及英文体现,部分产品必须要有阿拉伯文体现。 2.产品内外包装唛头,产品标签、铭牌应包含以下三项内容,缺一不可: 产品名称、产品型号、MADE IN CHINA。某些特殊产品要求见附件或者咨询工作人员。 3.其他信息如产品商标、公司名称等可以体现,SASO 的标志海关要求不能体现。 4.电器产品的唛头、标签及铭牌需要包含以下信息: 电压(单相:220V,230V,220/230V, 三相:380V,400V)频率( 60Hz )功率(如有)。如果有插头要符合BS 1363 标准,如果没有插头,请拍照具体体现。 5.所有信息应以喷印、印刻、不干胶黏贴等不能轻易移除的方式体现,内包装及产品上标签铭牌信息不可以普通纸张直接粘贴。大
什么是OSPF? OSPF的全称叫Open Shortest Path First,开放最短路径优先。Open的意思就是这个协议是公开性的,OSPF是由IETF标准组织制定的一种基于链路状态内部网关协议。(Shortest Path First)最短路径优先指的是路由选择过程中的一个算法,如果学过动态路由协议基础,就会知道OSPF是一种典型的IGP,是描述路由信息运行在同一个自制系统内部的动态路由协议。OSPF路由协议是一种典型的链路状态(Link-state)的路由协议,一般用于同一个路由域内。在这里,路由域是指一个自治系统(Autonomous System),即AS,它是指一组通过统一的路由政策或路由协议互相交换路由信息的网络。在这个AS中,所有的OSPF路由器都维护一个相同的描述这个AS结构的数据库,该数据库中存放的是路由域中相应链路的状态信息,OSPF路由器正是通过这个数据库计算出其OSPF路由表的。 OSPF的八大特点介绍 前文已经说明了OSPF路由协议是一种链路状态的路由协议,为了更好地说明OSPF 路由协议的基本特征,我们将OSPF路由协议与距离矢量路由协议RIP(Routing Information Protocol)作一比较,归纳为如下几点: 1、RIP路由协议中用于表示目的网络远近的参数为跳(HOP),也即到达目的网络所要经过的路由器个数。 在RIP路由协议中,该参数被限制为最大15,对于OSPF路由协议,路由表中表示目的网络的参数为Cost,该参数为一虚拟值,与网络中链路的带宽等相关,也就是说OSPF
路由信息不受物理跳数的限制。因此,OSPF适合应用于大型网络中,支持几百台的路由器,甚至如果规划的合理支持到1000台以上的路由器也是没有问题的。 2、RIP路由协议不支持变长子网屏蔽码(VLSM),这被认为是RIP路由协议不适用于大型网络的又一重要原因。 而产生VLSM的原因就是由于IP地址的匮乏。不支持VLSM极大的限制的网络的规划和IP地址分配的不合理。现在我们划分IP地址的时候通常掩码都是随意的,就是因为协议支持VLSM。 3、RIP路由协议路由收敛较慢。 路由收敛快慢是衡量路由协议的一个关键指标。RIP路由协议周期性地将整个路由表作为路由信息广播至网络中,该广播周期为30秒。在一个较为大型的网络中,RIP协议会产生很大的广播信息,占用较多的网络带宽资源;并且由于RIP协议30秒的广播周期,影响了RIP路由协议的收敛,甚至出现不收敛的现象。而OSPF是一种链路状态的路由协议,当网络比较稳定时,网络中的路由信息是比较少的,并且其广播也不是周期性的,因此OSPF 路由协议在大型网络中也能够较快地收敛。 4、在RIP协议中,网络是一个平面的概念,并无区域及边界等的定义。 在OSPF路由协议中,一个网络,或者说是一个路由域可以划分为很多个区域area,每一个区域通过OSPF边界路由器相连,区域间可以通过路由总结(Summary)来减少路由信息,减小路由表,提高路由器的运算速度。
立体商标与平面商标在功能上的区别是什么 商标类型有文字商标、图形商标、组合商标等,还有新颖的声音商标、立体商标等。今天我们来分析下立体商标和平面商标,看看立体商标和平面商标之间有什么区别。 立体商标 立体商标又叫三维商标,是以立体标志、商品整外型或商品的实体包装物以立体形象呈现的商标。简单的说就是以立体形状的商标。 立体商标、颜色组合商标与平面商标一起被统称为可视商标,立体商标的基本功能与平面商标一样,区别商品来源或服务提供者。 平面商标 平面商标是只由两维要素组成的视觉商标。它属于实体商标一类,绝大部分视觉商标都是平面商标。即商品的平面区别性商标,平面商标由文字、平面图形、字母、数字、颜色组合,或者上述要素的组合,平面商标的构成是一种艺术创造。 1、平面商标的特征 平面商标合法性是指商标的设计与使用要符合法律的有关要求与规定。例如,法律规定禁止将我国或外国的国旗、军旗等标志作为商标图案。厂商及商标设计者不应采用这些图案作为商标。
平面商标新颖性是指商标设计应具有独特的构思,新商标与原有商标比较有明显的区别与差异。新颖性是体现商标说明商品来源这一本质特征的必要条件。 平面商标表现性是指它只有通过实体形式才能得到表现。 2、平面商标的应用 平面商标在数量上居于各种类型商标的首位。绝大部分视觉商标都是平面商标。 立体商标与平面商标在功能上的区别 立体商标注册保护的一般性原则 1、合法性原则 同所有的商标一样,立体商标不得违反公共秩序和善良风俗,也不能在商品或服的性质、质量、产源方面欺骗消费者。 2、显著性原则 这里所说折在先权利是指在先的商标权和其它在先权,就在先商标权来说,我国刚开始保护立体商标,在目前还只有申请在先的权利,通过查询就可以避免冲突,至于其他在先权利,主要是在先的外观设计权,作为商标代理人,很难避免这方面的冲突,照一般商标注册的经验,在先也只有在公告期提异议或注册后提撤消注册不当来主张自己的权利。 立体商标注册保护的特殊原则 立体商标取得注册,除了必须遵守一般商标注册原则以外,还有一些特殊的要求,又被称为"限制性条件"。 1、商品自身性质产生的外型不能注册
1、设置SW1为VTP的服务器端,SW2和SW3为VTP的客户端。分成4个VLAN,VLAN号为1-4,2-4名称依次为xinxi 、zhihui、zuoye。Vtp的域名为ccnp,密码为cisco。 2、配置生成树,模式为PVST+。指定SW1为VLAN1-VLAN4的根桥,指定SW2为VLAN1和VLAN3的备份根桥,SW3为VLAN2和VLAN4的备份根桥。 3、在SW1和SW2之间配置二层链路聚合 路由器的其他参数参照拓扑图 5、按照逻辑拓扑所示配置OSPF,实现全网贯通。各PC要ping通其他PC。在area 2进行链路认证,明文,密码为cisco. 6、配置SW2只允许PC9和PC3 telnet。密码为cisco。 7、配置SW2和SW3端口安全,只允许如图所示的PC连接到网络,如果违规则关闭端口。8要求各PC接入到各自交换机后,交换机端口立即启动。 R1: //设置环回地址 Router(config)#int l0 Router(config-if)#ip ad 1.1.1.1 255.255.255.0
//配置端口地址和时钟 Router(config)#int f0/0 Router(config-if)#ip ad 192.168.4.254 255.255.255.0 Router(config-if)#no shut Router(config-if)#int s0/1/0 Router(config-if)#ip ad 23.1.1.2 % Incomplete command. Router(config-if)#ip ad 23.1.1.2 255.255.255.0 Router(config-if)#no shut //启用OSPF路由 Router(config-if)#router os 1 Router(config-router)#router-id 1.1.1.1 Router(config-router)#net 192.168.4.0 0.0.0.255 a 3 Router(config-router)#net 23.1.1.2 0.0.0.255 a 2 //设置虚链路把area 3根area 0连接起来Router(config-router)#a 2 virtual-link 2.2.2.2 Router(config-router)#exit R2: //设置环回地址 Router(config)#int l0 Router(config-if)#ip ad 2.2.2.2 255.255.255.0 //配置端口地址和时钟 Router(config)#int s0/1/00 Router(config-if)#int s0/0/0 Router(config-if)#ip ad 23.1.1.1 255.255.255.0 Router(config-if)#clock rate 64000 Router(config-if)#no shut Router(config-if)#int s0/1/0 Router(config-if)#ip ad 12.1.1.2 255.255.255.0 Router(config-if)#no shut //启用OSPF路由 Router(config-if)#router os 1 Router(config-router)#router-id 2.2.2.2 Router(config-router)#net 12.1.1.2 0.0.0.255 a 0 Router(config-router)#net 23.1.1.1 0.0.0.255 a 2 //设置虚链路把area 3根area 0连接起来Router(config-router)#a 2 virtual-link 1.1.1.1 Router(config-router)#exit R3: //设置端口地址和串口时钟 Router(config)#int s0/1/0 Router(config-if)#ip ad 12.1.1.1 255.255.255.0