EN 12020-2 EN 755-9
2
Tolerances for wall thickness - EN 755-9Page 4Tolerances for wall thickness - EN 12020-2
Page 5Tolerances for cross-sectional dimensions - EN 755-9Page 6Tolerances for cross-sectional dimensions - EN 12020-2Page 7Tolerances for convexity-concavity cross sectional - EN 755-9
Page 8Tolerances for convexity-concavity cross sectional- EN 12020-2
Page 9Tolerances for angularity - EN 755-9Page 10Tolerances for angularity - EN 12020-2Page 11Tolerances for contour - EN 755-9Page 12Tolerances for contour - EN 12020-2Page 13Tolerances for straightness - EN 755-9Page 14Tolerances for straightness - EN 12020-2Page 15Tolerances for twist - EN 755-9Page 16Tolerances for twist - EN 12020-2Page 17Tolerances for fixed length - EN 755-9Page 18Tolerances for fixed length - EN 12020-2Page 19Technical data Page 20Surface quality Page 21Profile dimensions
Page 22
??????????
?????????Contents
Narrow tolerances can reduce the productivity of the profile and thus the cost. This has to be taken into consideration when designing the profile.
Alumeco is working according to the Standards of European Committee for Standardization, CEN, EN 755-9 and EN 12020-2. In this handbook, you will find an extract of these standards. Text and values are taken from there.
The standards have to be considered as guidance. In the case of profiles which, due to the complexity of their design, are difficult to manufacture and specify, then special agreements between customer and Alumeco may need to be reached.
3
WALL THICKNESS
EN 755-9
Group 1 = EN AW-6101A, EN AW-6005, EN AW-6005A, EN AW-6060, EN AW-6063, EN AW-6063A
Group 2 = EN AW-6012, EN AW-6061, EN AW-6262, EN AW-6262A, EN AW-6082, EN AW-7020
4
5
B
C
C
CD
EN 12020-2
“ 100 % fokus on aluminium “
Thickness
Tolerance on wall thickness
Wall thickness A
Wall thickness B + C up to and inclu-ding 0 0 100 6 DIMENSIONS EN 755-9 Group 1 = EN AW-6101A, EN AW-6005, EN AW-6005A, EN AW-6060, EN AW-6063, EN AW-6063A Group 2 = EN AW-6012, EN AW-6061, EN AW-6262, EN AW-6262A, EN AW-6082, EN AW-7020 H H “ Technical advice“ CONVEXITY - CONCAVITY EN 755-9 8 “ Tailored solutions“ In the case of profiles with a width W of over 150 mm, the local deviation F1 shall not exceed 0.50 mm for any width W1 of 100 mm. 9 ANGULARITY EN 755-9 able deviation α for angles other than right angle shall be ± 1o 10 11 “ Worldwide network “ The maximum allow-able deviation α for angles other than right angle shall be ± 1o CONTOUR EN 755-9 12 W EN 12020-2 “ Logistics solutions“ W of the contour Contour tolerance = diameter C of the tolerance circle STRAIGHTNESS EN 755-9 14 1 h Baseplate EN 12020-2 “ Stock management“The local deviation from straightness h2 shall not exceed 0.3 mm per 300 mm length 15 EN 755-9 TWIST 1) Twist tolerances for lengths less than 1,000 mm shal be subject to agreement between the customer and Alumeco 16 *) Subejct to agreement between Alumeco and customer 17 LENGTH EN 755-9 18 19 *) Subejct to agreement between Alumeco and customer TECHNICAL DATA t = Wall thickness Temper Designations: T4: Solution heat treated and naturally aged. T6: Solution heat treated and artificially aged. T66: Solution heat treated and artificially aged. 20