起亚机床常见报警

SKT15/21常见报警

报警号序号屏幕显示信息含义

2000AL-0CP & FUSE TRIP数控模块保险丝熔断2001AL-1SPINDLE AMP ALARM主轴AMP报警

2002AL-2TAILSTOCK MOTOR OVERLOAD尾座电机过载

2003AL-3LUB. OIL LACK/FAULT润滑油不足或压力报警2004AL-4HYD. PRESSURE DROP液压压力不足

2005AL-5AIR PRESSURE DROP空气压力不足

2006AL-6X-AXIS TORQUE ALARM X轴扭矩报警

2007AL-7Z-AXIS TORQUE ALARM Z轴扭矩报警

2008AL-8

2009AL-9

2010AL-10

2011AL-11

2012AL-12POWER OFF NC ALARM断电报警

2013AL-13DOOR OPERATION INHIBIT安全门互锁

2014AL-14SPINDLE ROTATION FAULT主轴旋转故障

2015AL-15SPINDLE COMMAND TIME OVER主轴指令超时

2016AL-16Q-SETTER ARM DOWN对刀仪未收起

2017AL-17ROBOT FAULT机械手故障

2018AL-18

2019AL-19

2020AL-20ZERO RETURN INCOMPLETED回零未完成

2021AL-21

2022AL-22

2023AL-23

2024AL-24POWER OFF PROGRAM END自动断电程序结束2025AL-25SPINDLE ORIENTATION FAIL主轴定向失败

2026AL-26

2027AL-27

2028AL-28

2029AL-29

2030AL-30CHUCK CLAMP NG卡盘未夹紧

2031AL-31DOOR CLOSE NG安全门未关

2032AL-32CENTER POSITION NG顶尖位置不对

2033AL-33SPINDLE STOP INCOMPLETED主轴未完全停止

2034AL-34

2035AL-35END OF BAR棒料尾端

2036AL-36COUNT UP计数结束

2037AL-37SPINDLE-DOOR INTERLOCK主轴－安全门互锁2038AL-38

2039AL-39

2040AL-40

2041AL-41TURRET INDEX INHIBIT ZONE限制刀塔分度区域

2042AL-42HYDRULIC MOTOR OVERLOAD液压马达过载

2043AL-43COOLENT MOTOR OVERLOAD冷却马达过载

2044AL-44

2045AL-45

2046AL-46X-AXIS OVERTRAVEL X轴超程

2047AL-47Z-AXIS OVERTRAVEL Z轴超程

2048AL-48

2049AL-49

2050AL-50CHIP CONVEYOR OVERLOAD排屑器马达过载2051AL-51

2052AL-52PART CATCHER FAULT接料器故障

2053AL-53PC PARAMETER SET NG PC参数设置有误2054AL-54

2055AL-55

2056AL-56

2057AL-57

2058AL-58

2059AL-59

2060AL-60

2061AL-61

2062AL-62TURRET AMP ALARM刀塔AMP报警

2063AL-63TURRET COMPULSORY UNCLUMP刀塔未夹紧

2064AL-64TURRET INDEX TIME OVER刀塔分度超时

2065AL-65COMMAND TOOL NO. NG指令刀具号错误2066AL-66TURRET INDEX CONDITION NG刀塔分度条件未满足2067AL-67

2068AL-68

2069AL-69

2070AL-70

2071AL-71

2072AL-72

2073AL-73

2074AL-74

2075AL-75TURRET ADJUST MODE进入刀塔调整模式