AH266
High Voltage Hall Effect Latch
Features
- On-chip Hall plate
- Operating voltage: 4V~28V
- Output current: 400mA(Continuous , 25o C) - Reverse protection diode only for chip reverse power connecting (Note)
- Output protection Zener breakdown Vz=62V(Typ) - Package: SIP-4L
(Note)
Protection diode only exists at power pin(1,4) output, not including pin (2,3).
Application
- Dual-coil Brush-less DC Motor - Dual-coil Brush-less DC Fan - Revolution Counting - Speed Measurement
Pin Assignment
1. VCC
2. DO 4. GND
3. DOB
General Description
AH266 is an integrated Hall sensor with output drivers designed for electronic commutation of brush-less DC motor applications. The device includes an on-chip Hall voltage generator for magnetic sensing, a comparator that amplifies the Hall voltage, and a Schmitt trigger to provide switching hysteresis for noise rejection, and complementary darlington open-collector drivers for sinking large current loads. An internal bandgap regulator is used to provide temperature compensated supply voltage for internal circuits and allows a wide operating supply range.
If a magnetic flux density (B) is larger than operate point (Bop), DO turn on (low) and DOB turn off (high). The outputs state is latched prior to reach release point (Brp). if B< Brp, DO turn off and DOB turn on. AH266 is rated for operation over temperature range from -20o C to 85 o C and voltage range from 4V to 28V. The devices are available in low cost die forms or rugged 4 pin SIP packages.
Pin Configuration
Name Description
VCC Positive Power Supply DO
Output Pin DOB Output Pin GND
Ground
Ordering Information
AH266X -X X X -X
Packing Blank :Tube A :Taping
P:SIP-4L
Package Lead L :Lead Free Blank: Normal
Wafer Body Magnetic Characteristics
A~Z : if necessary to specify
AH266
High Voltage Hall Effect Latch
Block Diagram
1
REG.
Hall Plate
Amp
DO
DOB
Typical Application Circuit
124
3266
coil1coil2
Vcc
Brush-less DC Fan
Note: This application circuit can’t protect reverse coil current if power is connecting reverse.
AH266
High Voltage Hall Effect Latch
Absolute Maximum Ratings (at Ta = 250C )
Parameter
Symbol
Rating Unit
Supply voltage
VCC 28 V Output “OFF ” voltage Vout (off) 28 V Io (con) 400 (Note 1) mA Io (hold) 500 mA Output “ON” current
Io (peak) 700 mA
Magnetic flux density
B Unlimited Gauss Operating temperature range Top -20~+85 °
C Storage temperature range Tstg -65~+150 °C Power dissipation (Note 2) P
D 550 mW Thermal Resistance
θjc 227 °C/W
Note 1: Io(con) is 150 mA at 85°C
2: See Performance Characteristic for other conditions
Electrical Characteristics ( Ta = 25°C )
Characteristic Symbol
Conditions
Min Typ
Max
Unit
Supply Voltage
Vcc
- 4 - 28 V
Output Zener Breakdown Vz Output Turn off 54 62 70 V
Output Saturation Voltage Vce(sat) Vcc 24V, Ic 400mA - 1.1 1.5 V Output Leakage Current Icex Vce=24V, Vcc=24V - < 0.1 10 μA Supply Current Icc Vcc=24V, Output Open - 5 10 mA
Output Rise Time tr Vcc=24V, RL=820?, CL=20pF - 1.0 5 μs Output Falling Time tf Vcc=24V, RL=820?, CL=20pF
- 1.0 1.5 μs Switch Time Differential ?t
Vcc=24V, RL=820?, CL=20pF -
3.0 10 μs
Test Circuit
266
CL1
CL2
24V
Vout1(DO)
Vout2(DOB)
RL1=RL2=820 Ohm CL1=CL2=20 pF
RL2
RL1
AH266
High Voltage Hall Effect Latch
Magnetic Characteristics (Ta=+25o C)
(1mT = 10 Gauss) A grade
Characteristic
Symbol
Min.
Typ.
Max.
Unit
Operate Point Bop 10 - 70 Gauss Release Point Brp -70 - -10 Gauss Hysteresis Bhy - 80 - Gauss B grade
Characteristic
Symbol
Min.
Typ.
Max.
Unit
Operate Point Bop - - 100 Gauss Release Point Brp -100 - - Gauss Hysteresis Bhy - 80 - Gauss
O u t p u t V o l t a g e i n V o l t s
O u t p u t V o l t a g e i n V o l t s
Magnetic Flux Density in Gauss
Magnetic Flux Density in Gauss
DO
DOB
Bop
Bop
Brp
Brp
B hy Turn on
Turn off B hy Turn off Turn on Vsat
Vsat
Performance Characteristics (SIP-4L)
Ta (°C)
25 50 60 70 80 85 90 95 100
Pd (mW) 550 440 396 352 308 286 264 242 220 Ta (°C) 105 110 115 120 125 130 135 140 150 Pd (mW)
198 176 154 132 110 88 66 44 0
Power Dissipation Curve
01002003004005006000
15
3045607590105120135150Ta (。C)
Pd (mW)
85
AH266
High Voltage Hall Effect Latch
Operation Characteristics
Marking side
S
B hy
V sat
V cc
( O u t p u t V o l t a g e )
V d
rp
op
S
N
( Magnetic flux density )
DO
High
Low
( SIP4 )
N
Marking Information
266
Part Number
( Front View )
"2" = 2002
"1" = 2001
X XX X X
AH266
High Voltage Hall Effect Latch
Package Information
Active Area Depth
Package Sensor Location
0.7mm
1234
1.971mm
Package Dimension
14.25mm +/-1.25mm
1.03mm +/-0.1
+/-0.1mm
0.38mm +/-0.03mm
5.22m m +/-0.1m m 4.20m m +/-0.1m m
3.65mm +/-0.1mm
1.42mm+/-0.1mm
1.27mm +/-0.03mm
0.41mm +/-0.03mm
0.30mm +/-0.1mm
+/-0.03m m
0.46mm +/-0.03mm
0.2mm Max.5o
-7
o
o
3o
-5
3o -5
5o -7
o