https://www.wendangku.net/doc/8e14061024.html,
Dimensions are shown in mm Dimensions subject to change
Eurostyle D Subminiature Connectors
2
Cannon
Technical Data
Materials and Finishes Shell Steel, tin plated
Insulator Thermoplastic, UL 94V-0
Contacts
Copper alloy, gold over nickel plated Boardlock / Grounding Insert Brass, tin plated Threaded insert
Steel, tin plated
Electrical Data Current rating 5 A / 25°C, 3,5 A / 70°C ambient temperature Test voltage
1000 V ac rms at sea level Insulation resistance 5 G ? min.Contact resistance
25 m ?
Mechanical Data Polarizing
Keystone shaped front shell Number of contacts 9, 15, 25 and 37
Termination method Solder pin 90° Eurostyle acc.CECC 75301802
Performance class 3 (Standard)50 mating cycles (without code)Performance class 2200 mating cycles (code -A191)Performance class 1500 mating cycles (code -A190)Operating temperature
- 55°C to 125°C
Introduction
The D Subminiature Eurostyle connector is a product line extension of the well known D Subminiature family originally invented by ITT Industries, Cannon.
It is a special low profile 90° solder pin connector acc. to the CECC75 301 802European specification. It replaces the D*version with the code 1AEN which was not 100% in line with above mentioned specification.
Meets European Eurostyle specification CECC75 301 802
Available in all common layouts (9, 15, 25, 37-way), male and female Available in Performance Classes 1, 2 and 3 according to DIN 41652 Clinch nut with M3 or4-40 UNC thread Jack Post with M3 or 4-40 UNC thread
Product features
Introduction
The main applications will be found in industrial as well as in telecommunication equipment.The major advantage for the end user is to achieve additional space due to the low profile configuration.
The D Subminiature Eurostyle connectors are fully mateable with all standard D Subminiature connectors according to DIN 41652.
Dimensions are shown in mm Dimensions subject to change
https://www.wendangku.net/doc/8e14061024.html,
3
Eurostyle D Subminiature Connectors
Cannon
Order Reference
Series Prefix
Cannon designation Shell size E - 9 way A - 15 way B - 25 way C - 37 way Class
N - new generation
Termination / Mounting
E - 90° pushfit / row spacing 2,54
F - 90° pushfit / row spacing 2,84Number of contacts 9, 15, 25, 37Contact gender P - pin contact S - socket contact Contact termination L - solder pin Pushfit Type 0 - no pushfit 1 - for pcb 1,62 - for pcb 2,43 - for pcb 3,2Mounting height E - Euro 3,6
Locking
03 - M3 thread
04 - 4-40 UNC thread
13 - M3 thread with jackpost
14 - 4-40 UNC thread with jackpost Modification
no code - performance class 3A191 - performance class 2A190 - performance class 1
D A N
E - 15 S - L 1 - E 03 - *
Order Reference Explanation
Part numbers in red letter typeface indicate standard products: usually available with shorter lead times.
https://www.wendangku.net/doc/8e14061024.html,
Dimensions are shown in mm Dimensions subject to change
4
Cannon
Pin Connector 90°
Shell size Contacts A - 0,7 B + 0,25 C ±0,1 D + 0,25 E - 0,7F
DE 931,2016,7925,008,2312,902,54 or 2,84DA 1539,5025,1233,358,2312,902,54 or 2,84DB 2553,4038,8447,048,2312,902,54 or 2,84DC
37
69,70
55,30
63,50
8,23
12,90
2,54 or 2,84
03 - M3 thread
04 - 4-40 UNC thread
13 - M3 thread 14 - 4-40 UNC thread
Part numbers Pin
Shell size Layout
Clinch nut 4-40 UNC
Clinch nut M3
DE 9DENE-9P-L1-E04-A191DENE-9P-L1-E03-A191DA 15DANE-15P-L1-E04-A191DANE-15P-L1-E03-A191DB 25DBNE-25P-L1-E04-A191DBNE-25P-L1-E03-A191DC 37DCNE-37P-L1-E04-A191DCNE-37P-L1-E03-A191Shell size Layout Jackpost 4-40 UNC Jackpost M3
DE 9DENE-9P-L1-E14-A191DENE-9P-L1-E13-A191DA 15DANE-15P-L1-E14-A191DANE-15P-L1-E13-A191DB 25DBNE-25P-L1-E14-A191DBNE-25P-L1-E13-A191DC 37
DCNE-37P-L1-E14-A191
DCNE-37P-L1-E13-A191
Note: For performance class 1 replace A-191 by -A190;For performance class 3 delete -A191.Example: DENE-9P-L1-E13For row spacing 2,84 mm replace D*NE with D*NF Example: DANF-15P-L1-A191
Jackpost
clinch nut Part numbers in red letter typeface indicate standard products: usually available with shorter lead times.
Dimensions are shown in mm Dimensions subject to change
https://www.wendangku.net/doc/8e14061024.html,
5
Cannon
Socket Connector 90°
Shell size Contacts A - 0,7 B - 0,25 C ± 0,1 D - 0,25 E - 0,7F
DE 931,2016,4625,008,0212,902,54 or 2,84DA 1539,5024,7933,358,0212,902,54 or 2,84DB 2553,4038,5047,048,0212,902,54 or 2,84DC 37
69,70
54,9663,50
8,02
12,90
2,54 or 2,84
03 - M3 thread
04 - 4-40 UNC thread 13 - M3 thread 14 - 4-40 UNC thread
Part numbers Socket
Shell size
Layout Clinch nut 4-40 UNC Clinch nut M3
DE 9DENE-9S-L1-E04-A191DENE-9S-L1-E03-A191DA 15DANE-15S-L1-E04-A191DANE-15S-L1-E03-A191DB 25DBNE-25S-L1-E04-A191DBNE-25S-L1-E03-A191DC 37DCNE-37S-L1-E04-A191DCNE-37S-L1-E03-A191Shell size
Layout Jackpost 4-40 UNC Jackpost M3
DE 9DENE-9S-L1-E14-A191DENE-9S-L1-E13-A191DA 15DANE-15S-L1-E14-A191DANE-15S-L1-E13-A191DB 25DBNE-25S-L1-E14-A191DBNE-25S-L1-E13-A191DC
37
DCNE-37S-L1-E14-A191
DCNE-37S-L1-E13-A191
Note: For performance class 1 replace A-191 by -A190;For performance class 3 delete -A191.Example: DENE-9S-L1-E13For row spacing 2,84 mm replace D*NE with D*NF
Example: DANF-15S-L1-A191
Jackpost
clinch nut
Part numbers in red letter typeface indicate standard products: usually available with shorter lead times.
https://www.wendangku.net/doc/8e14061024.html,
Dimensions are shown in mm Dimensions subject to change
Eurostyle D Subminiature Connectors
6
Cannon
Pattern Hole
Signal Recommended PCB Contact ?Hole ?0,601,00Standard
Contact Arrangements PC Board Hole pattern - 90° European
Face View Pin Insert
Shell size
E Contact arrangement 9Contact size 20
Shell size
A Contact arrangement 15Contact size 20
Shell size
B Contact arrangement 2520
Shell size
C Contact arrangement 37Contact size 20
Mounting Recommended PCB Type Hole ?All 3,10
pushfit / row spacing 2,84
Product Safety Information
THIS NO TE SHO ULD BE READ IN CO N-JUNCTION WITH THE PRODUCT DATA SHEET/ CATALO GUE. FAILURE TO O BSERVE THE ADVICE IN THIS INFO RMATIO N SHEET AND THE O PERATING CO NDITIO NS SPECIFIED IN THE PRO DUCT DATA SHEET/CATALO GUE COULD RESULT IN HAZARDOUS SITUATIONS.
1.MATERIAL CONTENT AND PHYSICAL FORM
Electrical connectors do not usually contain hazardous materials. They contain conducting and non-conducting materials and can be divided into two groups.
a) Printed circuit types and low cost audio types which employ all plastic insulators and casings.
b) Rugged, Fire Barrier and High Reliability types with metal casings and either natural rubber, synthetic rubber, plastic or glass insulating materials.
Contact materials vary with type of connector and also application and are usually manufactured from either copper, copper alloys, nickel, alumel, chromel or steel. In special applications, other alloys may be specified.
2.FIRE CHARACTERISTICS AND ELECTRIC SHOCK HAZARD
There is no fire hazard when the connector is correctly wired and used within the specified parameters. Incorrect wiring or assembly of the connector or careless use of metal tools or conductive fluids, or transit damage to any of the component parts may cause electric shock or burns. Live circuits must not be broken by separating mated connectors as this may cause arcing, ionisation and burning. Heat dissipation is greater at maximum resistance in a circuit. Hot spots may occur when resistance is raised locally by damage, e.g. cracked or deformed contacts, broken strands of wire. Local overheating may also result from the use of the incorrect application tools or from poor quality soldering or slack screw terminals. Overheating may occur if the ratings in the Product Data Sheet/ Catalogue are exceeded and can cause breakdown of insulation and hence electric shock.
If heating is allowed to continue it intensifies by further increasing the local resistance through loss of temper of spring contacts, formation of oxide film on contacts and wires, and leakage currents through carbonisation of insulation and tracking paths. Fire can then result in the presence of combustible materials and this may
release noxious fumes. Overheating may not be
visually apparent. Burns may result from touching
overheated components.
3. HANDLING
Care must be taken to avoid damage to any
component parts of electrical connectors during
installation and use. Although there are normally
no sharp edges, care must be taken when handling
certain components to avoid injury to fingers.
Electrical connectors may be damaged in transit
to the customers, and damage may result in
creation of hazards. Products should therefore be
examined prior to installation/use and rejected if
found to be damaged.
4. DISPOSAL
Incineration of certain materials may release
noxious or even toxic fumes.
5. APPLICATION
Connectors with exposed contacts should not be
selected for use on the current supply side of an
electrical circuit, because an electric shock could
result from touching exposed contacts on an
unmated connector. Voltages in excess of 30 V ac
or 42.5 V dc are potentially hazardous and care
should be taken to ensure that such voltages can
not be transmitted in any way to exposed metal
parts of the connector body. The connector and
wiring should be checked, before making live, to
have no damage to metal parts or insulators, no
solder blobs, loose strands, conducting lubricants,
swarf, or any other undersired conducting
particles. Circuit resistance and continuity check
should be made to make certain that there are no
high resistance joints or spurious conducting paths.
Always use the correct application tools as
specified in the Data Sheet / Catalogue.
Do not permit untrained personnel to wire,
assemble or tramper with connectors. For
operation voltage please see appropriate natio-
nal regulations.
IMPORTANT GENERAL INFORMATION.
1. Air and creepage paths/Operating voltage
The admissible operating voltages depend on the
individual applications and the valid national and
other applicable safety regulations.
For this reason the air and creepage path data
are only reference values. Observe reduction of
air and creepage paths due to PC board and or
harnessing.
2. Temperature
All information given are temperature limits. The
operation temperature depends on the individual
application.
3. Other important information
Cannon continuously endeavours to improve their
products. Therefore, Cannon products may
deviate from the description, technical data and
shape as shown in this catalogue and data sheets.
元器件交易网https://www.wendangku.net/doc/8e14061024.html,