当前位置：文档库 › 电气类毕业论文外文翻译--视窗使用

电气类毕业论文外文翻译--视窗使用

英文原文：

Using Watch Window

Here are brief instructions for using the Watch Window in conjunction with ServLink to view and tune the variables for your 733. These instructions are meant to be intro -ductory. Full on-line help is available in each application. It is assumed that you al -ready have ServLink and Watch Window installed. The default installation location can be found by clicking the START icon (Microsoft Windows 95 or later) on the main menu bar and then clicking the PROGRAMS menu item. Look for an icon called WOODWARD WATCH WINDOW.

1. Make sure that all other programs that may access your computer communications port are shut down and you know the communication port connected to the control.

2. Start the ServLink server and open a new file. Select the proper COM port for your PC, verify that POINT TO POINT communications mode is selected, and verify that the baud rate matches the baud rate of the 733 control. See the on-line help file if you have been changing the port settings of your control.

3. Select OK. If everything is working right, you should see an animated picture of a string of ―1‖s and ―0‖s flying from the control to the PC on your screen. You now have a network definition file whose default name is NET1. You should save this file as ―your https://www.wendangku.net/doc/957280995.html,‖ (use FILE/SAVE AS). Link this name to your control part number since it will work only with that application. For instance, if the upper level control number is 8273-040, you could save the file as https://www.wendangku.net/doc/957280995.html,. Do not disconnect the server.

4. In the ServLink window you will now have another dialog window titled ―your https://www.wendangku.net/doc/957280995.html,‖. In this window you will see a ballhead icon and a control identifier name. Unless you have given the control a serial number (or name) with the SLSN.EXE program, this name will display as ―‖.

5. Start the Watch Window application. When Watch executes, you will have a screen displaying three windows entitled Watch Window, Explorer, and Inspector.

6. The Explorer window will have two groups displayed, SERVICE and CONFIGURE. Double clicking on either of these will expand them to show groups of values. Explorer is used only to locate a tunable or monitor value. In order to

change a value or monitor a value, you must drag and drop a value from the Explorer window into the Inspector window.

7. Once a value is displayed in the Inspector, you can see several blocks of information. The most important blocks for a tunable value are the FIELD and VALUE blocks. The FIELD block is used to identify a particular value, and the VALUE block displays the current value of a variable. There are two types of values available in Watch. One is a monitor value, which is marked in the INSPECTOR window with a pair of glasses. This means it may only be looked at. The other value is a read/write value, which is marked with a pencil. The read/write type may be modified using the up and down arrows in the value block.

Chapter 5.

Service Options

Product Service Options

The following factory options are available for servicing Woodward equipment,based on the standard Woodward Product and Service Warranty

(5-01-1205) that is in effect at the time the product is purchased from Woodward or the service is performed:

? Replacement/Exchange (24-hour service)

? Flat Rate Repair

? Flat Rate Remanufacture

If you are experiencing problems with installation or unsatisfactory performance of an installed system, the following options are available:

? Consult the troubleshooting guide in the manual.

? Contact Woodward technical assistance (see ―How to Contact Woodward‖ later in this chapter) and discuss your problem. In most cases, your problem can be resolved over the phone. If not, you can select which course of action you wish to pursue based on the available services listed in this section.

Replacement/Exchange

Replacement/Exchange is a premium program designed for the user who is in need of immediate service. It allows you to request and receive a like-new replacement unit in minimum time (usually within 24 hours of the request), providing a suitable unit is available at the time of the request, there by minimizing costly

downtime. This is also a flat rate structured program and includes the full standard Woodward product warranty (Woodward Product and Service Warranty 5-01-1205). This option allows you to call in the event of an unexpected outage, or in advance of a scheduled outage, to request a replacement control unit. If the unit is available at the time of the call, it can usually be shipped out within 24 hours. You replace your field control unit with the like-new replacement and return the field unit to the Woodward facility as explained below (see ―Returning Equipment for Repair‖ later in this chapter).

Charges for the Replacement/Exchange service are based on a flat rate plus shipping expenses. You are invoiced the flat rate replacement/exchange charge plus a core charge at the time the replacement unit is shipped. If the core (field unit) is returned to Woodward within 60 days, Woodward will issue a credit for the core charge. [The core charge is the average difference between the flat rate replacement/exchange charge and the current list price of a new unit.]

Return Shipment Authorization Label. To ensure prompt receipt of the core, and avoid additional charges, the package must be properly marked. A return authorization label is included with every Replacement/Exchange unit that leaves Woodward. The core should be repackaged and the return authorization label affixed to the outside of the package. Without the authorization label, receipt of the returned core could be delayed and cause additional charges to be applied.

Flat Rate Repair

Flat Rate Repair is available for the majority of standard products in the field. This program offers you repair service for your products with the advantage of knowing in advance what the cost will be. All repair work carries the standard Woodward service warranty (Woodward Product and Service Warranty 5-01-1205) on replaced parts and labor.

Flat Rate Remanufacture

Flat Rate Remanufacture is very similar to the Flat Rate Repair option with the exception that the unit will be returned to you in ―like-new‖ condition and carry with it the full standard Woodward product warranty (Woodward Product and Service Warranty 5-01-1205). This option is applicable to mechanical products only.

Returning Equipment for Repair

If a control (or any part of an electronic control) is to be returned to Woodward

forrepair, please contact Woodward in advance to obtain a Return Authorization Number. When shipping the item(s), attach a tag with the following information: ? name and location where the control is installed;

? name and phone number of contact person;

? complete Woodward part number(s) and serial number(s);

? description of the problem;

? instructions describing the des ired type of repair.

Packing a Control

Use the following materials when returning a complete control:

? protective caps on any connectors;

? antistatic protective bags on all electronic modules;

? packing materials that will not damage the surface o f the unit;

? at least 100 mm (4 inches) of tightly packed, industry-approved packing

material;

? a packing carton with double walls;

? a strong tape around the outside of the carton for increased strength. Return Authorization Number

When returning equipment to Woodward, please telephone and ask for the Customer Service Department [1 (800) 523-2831 in North America or +1 (970) 482-5811]. They will help expedite the processing of your order through our distributors or local service facility.

To expedite the repair process, contact Woodward in advance to obtain a Return Authorization Number, and arrange for issue of a purchase order for the item(s) to be repaired. No work can be started until a purchase order is received.

Replacement Parts

When ordering replacement parts for controls, include the following information: ? the part number(s) (XXXX-XXXX) that is on the enclosure nameplate;

? the unit serial number, which is also on the nameplate.

How to Contact Woodward

In North America use the following address when shipping or corresponding: Woodward Governor Company

PO Box 1519

1000 East Drake Rd

Fort Collins CO 80522-1519, USA

Telephone—+1 (970) 482-5811 (24 hours a day)

Toll-free Phone (in North America)—1 (800) 523-2831

Fax—+1 (970) 498-3058

For assistance outside North America, call one of the following international Woodward facilities to obtain the address and phone number of the facility nearest your location where you will be able to get information and service.

Facility Phone Number

Brazil +55 (19) 3708 4800

India +91 (129) 4097100

Japan +81 (476) 93-4661

The Netherlands +31 (23) 5661111

You can also contact the Woodward Customer Service Department or consult our worldwide directory on Woodward’s website (https://www.wendangku.net/doc/957280995.html,) for the name of your nearest Woodward distributor or service facility.

Engineering Services

Woodward Industrial Controls Engineering Services offers the following aftersales support for Woodward products. For these services, you can contact us by telephone, by email, or through the Woodward website.

? Technical Support

? Product Training

? Field Service

Contact information:

Telephone—+1 (970) 482-5811

Toll-free Phone (in North America)—1 (800) 523-2831

Email—icinfo@https://www.wendangku.net/doc/957280995.html,

Website—https://www.wendangku.net/doc/957280995.html,

Technical Support is available through our many worldwide locations or our authorized distributors, depending upon the product. This service can assist you with technical questions or problem solving during normal business hours. Emergency assistance is also available during non-business hours by phoning our toll-free number and stating the urgency of your problem. For technical support, please contact us via telephone, email us, or use our website and reference Customer Services and then Technical Support.

Product Training is available at many of our worldwide locations (standard classes). We also offer customized classes, which can be tailored to your needs and can be held at one of our locations or at your site. This training, conducted by experienced personnel, will assure that you will be able to maintain system reliability and availability. For information concerning training, please contact us via telephone, email us, or use our website and reference Customer Services and then Product Training.

Field Service engineering on-site support is available, depending on the product and location, from one of our many worldwide locations or from one of our authorized distributors. The field engineers are experienced both on Woodward products as well as on much of the non-Woodward equipment with which our products interface. For field service engineering assistance, please contact us via telephone, email us, or use our website and reference Customer Services and then Technical Support.

Appendix A.

Connector Information

The 733 is not shipped with mating connectors because many applications may have a standard wiring harness or it is desirable to have the mating connectors in advance for wiring harness wiring. However, for service and convenience, Woodward also carries 733 connector kits that contain all of the mating terminal blocks used on the 733.

A single kit (8928-7039) is necessary for the 733 control. Two separate kits are necessary for the 766. Kit 8928-7039 provides connection for the control signals via the black connectors. Kit 8928-7040 provides connection for the control signals via the white connectors. These kits use the Delphi-Packard connectors.

? Kit 8928-7039 contains 1 each of the 2 black connectors (30 signals each), 65 hand crimp sockets, and 1 removal tool

? Kit 8928-7040 contains 1 each of the 2 white connectors (30 signals each), 65 hand crimp sockets, and sealing plugs for all unused terminals.

The sealed connectors on the 733 are not designed for removal by hand. After inp ut power is disconnected, the connectors can be removed using a ?‖ inch nut driver. When reinstalling the connectors, use 1.7–2.3 N m (15–20 lbf-in) torque for the jackscrew. Using the correct torque is required to both avoid damage and provide proper force on the gasket for a moisture seal.

Two manufacturers make connectors that will mate with the 733. Each manufacturer has different application limitations. A comparison of each is provided in the table below to assist in proper selection. The connectors from both manufacturers match the color of the 733 headers and have matching polarization keys.

Table A-1. Mating Connector Comparison

Delphi-Packard Mating Connectors

These connectors use a ―pull-to-seat‖ design. To use the connectors, it is first necessary to pull each wire through the connector, strip the wire, crimp on a terminal, and finally pull the wire back into the connector body to seat it into the connector locking mechanism. Care must be taken to align the terminal correctly with the connector when pulling it back into the connector body. If it must be removed, a special tool is necessary to avoid damage to the wire, terminal, and connector.

A crimp tool is necessary for proper field crimping of the mating terminals. Use Woodward P/N 8996-2015 for this purpose. In practice, we have found that it is necessary to use the correct crimping tool to avoid damaging the terminals. If the wrong tool is used, the terminals bend easily and can break.

Individual wires can be removed using an extraction tool. If a wire must b removed from the connector, a removal tool is necessary to avoid damage to the connector. Use Woodward P/N 8996-2016 for this purpose. One extraction tool is provided with each control board connector kit (the kit with the black connectors). Using the wrong removal tool will very likely result in damage to the internal connector retaining clip. Insert the tool and twist about 90 degrees then pull the wire and tool out together.

Those who wish to create standard harnesses may want to purchase the connectors in bulk and have the socket terminals on reels for automated assembly. In support of this need, the manufacturer part numbers are provided.

Table A-2. Delphi-Packard Parts

Cinch Mating Connectors

These connectors use a ―push-to-seat‖ design. To use the connectors, it is first necessary to strip the wire, crimp on a terminal, and then push the wire into the

connector body from the back to seat it into the connector locking mechanism. Care must be taken to align the terminal correctly with the connector when pushing it into the connector body. If it must be removed, a special tool is necessary to avoid damage to the wire, terminal, and connector.

A crimp tool is necessary for proper field crimping of the mating terminals. In practice, we have found that it is necessary to use the correct crimping tool to avoid damaging the terminals. If the wrong tool is used, the terminals bend easily and can break.

Individual wires can be removed using an extraction tool. If a wire must be removed from the connector, a removal tool is necessary to avoid damage to the connector. One extraction tool is provided with each control board connector kit (the kit with the black connectors). Using the wrong removal tool will very likely result in damage to the internal connector retaining clip. Insert the tool and twist about 90 degrees then pull the wire and tool out together.

Table A-3. Cinch Parts

Recommended Wire Size and Types

The Society of Automotive Engineers (SAE) has a standard for on-engine cabling called J1128. It covers many wire sizes and types. For individual wiring, the TXL, GXL, and SXL wire types are common. TXL is Thin Wall, Cross Linked Polyolefin Insulated and has the thinnest insulation. GXL is General Purpose, Cross Linked Polyolefin Insulated and has a medium size insulation thickness. SXL is Special Purpose, Cross Linked Polyolefin Insulated and has a very thick insulation

layer. Each type has different characteristics. In relation to the connector on the 733, the important characteristic difference between these cable types is the insulation thickness.

Only the TXL and GXL wire types are recommended for use with the 733. Though SXL is a common and very good wire type, the insulation thickness is too large to be used in the 733 connectors.

Table A-4. Wire Sizes

Wire Gauge—AWG to Metric Comparison

Table A-5. Wire Gauge Comparison

Table A-5 is intended as a guide for determining the wire size that will fit into the 733 connector(s). The wire size must also be evaluated for the maximum current rating for each connection. Most places in this manual refer to various AWG sizes as being equal to common metric sizes. For example, 20 AWG is noted the same as 0.5 mm2. Though they are not exactly the same physical sizes, their use is interchangeable.

Appendix B.

Commissioning Procedure

The procedures below relate specific block input and output names for clarity.

A specific customer application may use different names for the same functions due to inclusion of interface blocks. This procedure should be re-written by the engineer who creates the customer specific application in order to be appropriate docu

-mentation.

Control I/O Commissioning

In order to verify correct installation wiring and safe starting and stopping capability, it is necessary to check all control I/O functionality.

Verify wiring using current injection, digital multi-meters, visual inspection, and any other means necessary. Verify wiring polarity as well.

Verify that each output point is connected to the correct device by using test modes in the software and verifying correct actuator / relay movement.

Verify that each input point is connected to the correct device by using current or voltage injection in place of the devices for analog and digital inputs. Communications networks will require special communications equipment to validate.

中文译文：

视窗使用

下面是使用视窗结合ServLink查看并调整您 733 的变量的简要说明。这些指令是注定要的介绍。每个应用程序可使用完整的在线帮助。假定您已经有了ServLink，并且安装监视窗口。在默认安装位置，可通过单击主菜单栏上的启动图标（Microsoft Windows 95 或更高版本），然后单击程序菜单项。寻找一个称为伍德沃德视窗的图标。

1.请确保关闭其他所有程序，可能会访问您的计算机的通信端口，并且是您

知道的通信端口连接到该控件。

2.启动 ServLink 服务器并打开一个新的文件。为您的个人电脑选择适当的

COM 端口，验证已选定的点到点的通信模式，和验证的波特率匹配的 733 控制的波特率。如果您一直在改变您的控件的端口设置，请参阅联机帮助文件。

3．选择确定。如果一切正常，您应该看到一个动画画的是一连串的“1”s和“0”s飞舞的控制到你的电脑屏幕上。现在可以通过网络定义文件的默认名称是 net1。您应保存此文件作为"您的 https://www.wendangku.net/doc/957280995.html,"（使用文件/另

存为）。因为它将只使用该应用程序，请将此名称链接到您的控制部件号。

例如，如果上游水位控制数 8273-040，可以作为 https://www.wendangku.net/doc/957280995.html, 保存该文件。请勿断开连接的服务器。

4. 在 ServLink 窗口中，您将会有另一个标题为"你的 https://www.wendangku.net/doc/957280995.html,"的对

话框窗口。在此窗口中，您将看到一个 ballhead 的图标和一个控件的标识符名称。除非您已经授予控制编号 (或名称) 的 SLSN。EXE 程序，此

名称将显示为""。

5. 启动视窗应用程序。监视执行时，您会有屏幕，显示三个窗口，题为视窗、

资源管理器，和检查器。

6. 资源管理器窗口将拥有两组显示，服务和配置。双击这些之一将扩大他们

来显示组的值。资源管理器只用于查找可调谐或监视值。为了更改值或监视的值，必须拖动，并从资源管理器窗口的值放到检查器窗口。

7. 一旦检查器中显示的值，您可以看到几个街区的信息。可调谐值的最重要

的块是字段和值块。田块用于标识特定的值，值块显示变量的当前值。有两种类型的值在表中可用。其中一个是显示器的值，这一副眼镜检查器窗

口中标记。这意味着它只可看着。另一个值是一个读/写的值，这标有一

支铅笔。读/写类型可能会修改使用向上和向下箭头中的值块。

第五章服务选项

产品服务选项

下面是基于伍德沃德标准产品和服务质保（5-01-1205）的设备维护和保养的服务条款。在购买产品或服务时生效。

?更换(24 小时服务)

?统一费用维修

?统一费用大修

如果在安装的过程中遇到问题或者对系统安装之后的运行性能不满意的话，可以参考下面的选项：

?参考手册中的故障排除指南。

?联系伍德沃德技术援助（请参阅本章后面的"如何联系伍德沃德"）并说明您的问题。大多数情况下，可以在电话里解决您的问题。如果解决不了的话，您可以在本节所列出的可选的服务中选择您所需要的。

更换

更换是为那些需要紧急服务的客户提供的收费项目。您有需求时，只要有备件，您就会在最短的时间内收到一个近乎全新的替代部件（通常在24小时之内），使停工造成的损失最小化。这同样属于统一费用项目并包括所有伍德沃德标准产品质保（伍德沃德产品和服务质保5-01-1205）。

选择此选项就可以在发生故障导致停工或发生故障之前打电话要求更换控制器部件。只要此时有备件，将在24小时之内寄出。使用新部件替换现场的控制器部件并将其发回伍德沃德工厂（见本章后面的“返厂维修”）。

更换服务的收费标准是统一费用加运费。备用件发出时您会收到换件的费用加上核心费用的发票。如果核心（现场故障部件）在60天之内寄回伍德沃德，我们将退还核心费用。[核心费用为换件统一费用与新部件的当前价格的平均值。

返厂许可标志。为保证迅速收到核心部件并避免额外的费用，包装必须加盖此标志。回运许可标志在每一个伍德沃德发出的备件中都能找到。讲换下的核心部件重新包装并在外包装上粘贴返厂许可标志。如果没有这样做的话，受到核心

返厂的时可能会推迟，从而影响额外的费用。

统一费用维修

统一费用维修面对的是大多数现场的标准产品。这样的优点是在维修之前您就能了解所需费用。所有的维修工作都执行伍德沃德换件和工时标准服务质保（伍德沃德产品和服务质保5-01-1205）。

统一费用大修

统一费用大修与统一费用维修非常相似，您将会得到一个近乎全新的部件并符合伍德沃德标准产品质保（伍德沃德产品和服务质保5-01-1205）。但是此选项只适用于机械产品。

设备返修

如果控制器（或任何电控部件）需要返回伍德沃德修理的话请事先联系伍德沃德以获得返回许可编号。发运时请粘贴包含以下信息的标签：

?名称和安装地点；

?联系人姓名及联系电话；

?完整的伍德沃德件号和序列号；

?故障描述；

?注明需要哪种维修。

控制器的包装

将整个控制器返厂时需要用到以下材料：

?每个端子的防护帽；

?所有电子模块的静电防护袋；

?防止设备外表损坏的包装填充物；

?紧密填充至少100mm（4英寸）的工业许可填充物；

?双面包装硬纸盒；

?使用结实的胶带封住纸盒以增加强度

返厂许可编号

设备返回伍德沃德之后请致电客户服务部[1（800）523-2831 北美或 +1（970）482-5811]。客户服务人员将会通过联系我们的代理人或当地的分公司来提高订单的处理速度。为了升速维修过程请您事先联系伍德沃德以获得返厂许可

编号，同时发出需维修部件的订购单。收到订购单之前我们无法处理。

替换部件

订购控制器替换部件需要包含以下信息：

?铭牌上的件号（XXXX-XXXX）；

?铭牌上的序列号。

如何联系伍德沃德

在北美使用下列地址当运输或类似时:

伍德沃德总公司

信箱 1519 1000 东德雷克 Rd 柯林斯公司 80522-1519，美国电话—— + 1 (970) 482-5811 (24 小时) 免费电话（北美地区）—— 1 (800) 523-2831 传真—— + 1 (970) 498-3058

北美以外的援助调用一个以下国际的伍德沃德设施，以获得最接近您的位置，您将能够获得信息和服务设施的地址和电话号码。

便利的设施电话号码

巴西 + (19) 3708 4800

印度 + 91 (129) 4097100

日本 + 81 (476) 93 4661

荷兰 +31 (23) 5661111

你也可以与伍德沃德客户服务部门联系，或咨询我们的全球目录在伍德沃德的网站(https://www.wendangku.net/doc/957280995.html,)离你最近的名字伍德沃德分销商或服务设施。

技术服务

伍德沃德工业控制技术服务对于伍德沃德产品提供如下支持。您可以通过电话，电邮和网站联系我们以获得这些服务。

?技术支持

?产品培训

?现场服务

联系信息：

电话— + 1 (970) 482-5811

免费电话（北美）— 1 (800) 523-2831

Email—icinfo@https://www.wendangku.net/doc/957280995.html,

Website—https://www.wendangku.net/doc/957280995.html,

技术支持是根据产品由我们各地的分公司和代理商来提供的。此项服务可以在工作日帮您解决技术问题。非工作日需要紧急援助请拨打我们的免费电话。需要获得技术支持请通过电话，电邮或网站联系我们。

产品培训大多数的分公司都可以提供产品培训（标准培训）。我们同样可以提供定制的培训，在我们的分公司或你们的场所举行为您量身定制的培训。此培训由经验丰富的工程师主持，保证能够使您的系统稳定运行。如果想要获得关于培训的信息，请通过电话，电邮或网站联系我们。

现场服务根据产品我们各地的分公司和代理商可以提供现场的工程技术服务。现场工程师对于伍德沃德的产品以及与之匹配的许多非伍德沃德产品都非常了解。如果想要获得现场服务，请通过电话，电邮或网站联系我们。

附录A。

连接器信息

733 不附带交配连接器，因为许多应用程序可能有标准的线束或最好的电线束布线事先有交配的连接器。然而，为了服务和方便，伍德沃德也进行 733 连接器套件包含了所有 733 上使用的交配的接线端子。

一个单一的工具包 (8928-7039) 对733 的控制有必要的。所需的是 766 的两个单独的工具。8928-7039工具包通过黑色连接器提供控制信号来连接。8928-7040工具包通过白色连接器提供控制信号来连接。这些工具包使用德尔福派克连接器连接。

每个8928-7039工具包包含1到2个黑色连接器（每个30个信号），65手卷曲插座和一个删除工具

每个8928-7040工具包包含1到2个白色连接器（每个30个信号），65手卷曲插座和给所有未使用的终端密封的插头。

733 的密封连接器不是设计为手工去除的。输入的电源断开连接后，可以使用“1/4”英寸螺母驱动器来删除连接器。当重新安装连接器时，请使用 1.7–2.3 N m （ 15-20- lbf）扭矩的螺旋千斤顶。为避免伤害到连接器，必须使用正确的扭矩和给潮湿的密封垫圈提供一个适当的力。两个厂商将作出匹配733 的连接器。每个厂商都有不同的应用软件的局限性。下表提供的两个厂商之间的比较有助于您做出正确的选择。两个厂商的连接器与 733 的标题的颜色匹配，并具有匹配的偏振钥匙。

表格A-1 交配连接器比较

德尔福派克交配连接器

这些连接器使用“拉拨座”的设计。若要使用这些连接器，首先要拉动每根电线通过这些连接器，然后卸下电线，并卷起来放在终端上,最后把电线拉回到连接器内并使连接器锁定此机制电线。当要把它拉回连接器内时，要小心谨慎,

使终端与连接器正确相连。如果它必须删除,一种特殊的工具是必要的,以避免损坏线、终端和连接器。

为对配套终端进行适当的字段压缩，一个压缩工具是必要的。伍德沃德 P/N 8996-2015 年就是此用途。在实践中,我们发现,必须使用正确的压缩工具以避免损伤终端。如果使用了错误的工具，则终端容易弯曲和可以被打断。

使用提取工具，可以删除个别电线。如果必须从连接器删除电线，删除工具是避免损坏连接器所必需的。伍德沃德 P/N 8996-2016 就是用于此目的。一个提取工具提供了每个控制板的连接器工具箱（带黑色接头的工具箱）。。使用错误的删除工具很可能会导致在固定夹的内部接头损坏。插入工具并扭转约 90 度，然后把电线和工具一起拉出。

那些想创建标准线束的人可能要大量购买散装连接器和插座终端对角子机的自动装配。为了支持这个需要,厂商提供零件编号。

表格A-2 德尔福派克部件

辛奇交配连接器

这些连接器使用“拉拨座”的设计。若要使用这些连接器，首先要卸下电线，并卷起来放在终端上,最后把电线拉回到连接器内并使连接器锁定此机制电线。当要把它拉回连接器内时，要小心谨慎, 使终端与连接器正确相连。如果它必须删除,一种特殊的工具是必要的,以避免损坏线、终端和连接器。

使用提取工具，可以删除个别电线。如果必须从连接器删除电线，删除工具是避免损坏连接器所必需的。伍德沃德 P/N 8996-2016 就是用于此目的。一个

提取工具提供了每个控制板的连接器工具箱（带黑色接头的工具箱）。。使用错误的删除工具很可能会导致在固定夹的内部接头损坏。插入工具并扭转约 90 度，然后把电线和工具一起拉出。

那些想创建标准线束的人可能要大量购买散装连接器和插座终端对角子机的自动装配。为了支持这个需要,厂商提供零件编号。

表格A-3 辛奇部件

推荐线号和类型

表格A-4 线号

汽车工程师的社会(SAE) 对发动机布线有一个标准，该标准被称为J1128。它涵盖了许多电线的大小和类型。对于个别线路,这个TXL、GXL、SXL类型的电线是通用的。TXL薄壁，交叉连接的聚烯烃是最薄的绝缘。GXL是通用的,交叉联系在一起的聚烯烃保温和有一个中等大小绝缘厚度。SXL有专用用途，交叉连接的聚烯烃,有很厚的绝缘保温层。每种类型都有不同的特性。相对于在733上的连接器,区别的重要特征是这些电缆的类型和绝缘厚度。

733 用推荐使用的只有TXL类型和GXL类型。虽然 SXL 是一种常见的和很好的电线类型，但它绝缘厚度太大，无法在 733 连接器中使用。

线规————AWG 度量标准对比

表格A-5 线规对比

表格A-5作为指南用于确定放入 733 接头的电线的大小。此外必须依据每个连接件的最大额定电流来计算电线的大小。本手册中的大部分地方涉及到不同的AWG的尺寸就是等于常见的米制尺寸。例如，20 AWG显然和0.5平方毫米是一样的。虽然他们不是完全相同的物理尺寸,但它们的用途是可互换的。