文档库 最新最全的文档下载
当前位置:文档库 › NSSW064T中文资料

NSSW064T中文资料

No. STSE-CC7196A

SPECIFICATIONS FOR NICHIA CHIP TYPE WHITE LED

MODEL : NSSW064T

NICHIA CORPORATION

Nichia STSE-CC7196A

1.SPECIFICATIONS

(1) Absolute Maximum Ratings (Ta=25°C)

Item Symbol Absolute Maximum Rating Unit

Forward Current I F 35 mA Pulse Forward Current I FP 100 mA Allowable Reverse Current I R 85 mA Power Dissipation P D 133 mW Operating Temperature T opr -40 ~ +110 °C Storage Temperature T stg -40 ~ +110 °C Dice Temperature T j 125 °C Soldering Temperature T sld Reflow Soldering : 260°C for 10sec.

Hand Soldering : 350°C for 3sec.

I FP Conditions : Pulse Width 10msec. and Duty 1/10

(2) Thermal Characteristics (Ta=25°C)

Item Symbol Typ. Unit

Rja 300 °C/W

Heat resistance

Rjs 120 °C/W

? Rja = Heat resistance from Dice to Ambient temperature (Ta)

Rjs = Heat resistance from Dice to Solder temperature of Cathode Side (Ts) ? Using Nichia standard circuit board FR4, t=1.6mm, Copper foil, t=35μm

(3) Initial Electrical/Optical Characteristics (Ta=25°C)

Item Symbol Condition Typ. Max. Unit

Forward Voltage V F I F =30[mA](3.4) 3.8 V Luminous Intensity Iv I F =30[mA](2600)- mcd Luminous Intensity Iv I F =20[mA](1900)- mcd

x - I F =30[mA]0.31 - -

Chromaticity Coordinate

y - I F =30[mA]0.32 - -

? Please refer to CIE 1931 chromaticity diagram.

(4) Ranking

(Ta=25°C)

Item

Symbol Condition Min. Max. Unit Rank X Iv

I F =30[mA]2880 4000 mcd Rank W Iv

I F =30[mA]2000 2880 mcd Luminous Intensity Rank V Iv

I F =30[mA]1440 2000 mcd

? Luminous Intensity Measurement allowance is ± 10%.

Color Ranks (I F =30mA,Ta=25°C)

Rank a0 Rank b1 x 0.280 0.264 0.283 0.296x 0.287 0.283 0.330 0.330

y 0.248 0.267 0.305 0.276

y 0.295 0.305 0.360 0.339

?<= <=

Nichia STSE-CC7196A

Rank b2 Rank c0

x 0.296 0.287 0.330 0.330x 0.330 0.330 0.361 0.356

y 0.276 0.295 0.339 0.318y 0.318 0.360 0.385 0.351 Color Coordinates Measurement allowance is ± 0.01.

Basically, a shipment shall consist of the LEDs of a combination of the above ranks.

The percentage of each rank in the shipment shall be determined by Nichia.

2. INITIAL OPTICAL/ELECTRICAL CHARACTERISTICS

Please refer to figure’s page.

3.OUTLINE DIMENSIONS AND MATERIALS

Please refer to figure’s page.

Material as follows ; Package : Heat-Resistant Polymer

Encapsulating Resin : Silicone Resin (with Diffused + Phosphor)

Electrodes : Ag Plating Copper Alloy

4.PACKAGING

· The LEDs are packed in cardboard boxes after taping.

Please refer to figure’s page.

The label on the minimum packing unit shows ; Part Number, Lot Number, Ranking, Quantity

· In order to protect the LEDs from mechanical shock, we pack them in cardboard boxes for transportation. · The LEDs may be damaged if the boxes are dropped or receive a strong impact against them,

so precautions must be taken to prevent any damage.

· The boxes are not water resistant and therefore must be kept away from water and moisture.

· When the LEDs are transported, we recommend that you use the same packing method as Nichia.

5.LOT NUMBER

The first six digits number shows lot number.

The lot number is composed of the following characters;

- U

- Year ( 6 for 2006, 7 for 2007 )

- Month ( 1 for Jan., 9 for Sep., A for Oct., B for Nov. )

- Nichia's Product Number

U - Ranking by Color Coordinates

- Ranking by Luminous Intensity

Nichia STSE-CC7196A

6.RELIABILITY

(1) TEST ITEMS AND RESULTS

Test Item Standard

Test Method Test Conditions Note

Number of

Damaged

Resistance to Soldering Heat (Reflow Soldering) JEITA ED-4701

300 301

Tsld=260°C, 10sec.

(Pre treatment 30°C,70%,168hrs.)

2 times 0/22

Solderability (Reflow Soldering) JEITA ED-4701

300 303

Tsld=215 ± 5°C, 3sec.

(using flux, Lead Solder)

1 time

over 95%

0/22

Thermal Shock JEITA ED-4701

300 307 -40°C ~ 110°C

1min. (10sec.) 1min.

(Pre treatment 30°C,70%,168hrs.)

100 cycles 0/100

Temperature Cycle JEITA ED-4701

100 105

-40°C ~ 25°C ~ 110°C ~ 25°C

30min. 5min. 30min. 5min.

100 cycles 0/100

Moisture Resistance Cyclic JEITA ED-4701

200 203

25°C ~ 65°C ~ -10°C

90%RH 24hrs./1cycle

10 cycles 0/100

High Temperature Storage JEITA ED-4701

200 201

Ta=110°C 1000 hrs. 0/100

Temperature Humidity Storage JEITA ED-4701

100 103

Ta=60°C, RH=90% 1000 hrs. 0/100

Low Temperature Storage JEITA ED-4701

200 202

Ta=-40°C 1000 hrs. 0/100

Steady State Operating Life Ta=25°C,

I F=35mA 1000

hrs.

0/100

Steady State Operating Life of High Temperature Ta=85°C,

I F=30mA 1000

hrs.

0/100

Steady State Operating Life of High Humidity Heat 60°C, RH=90%, I F=30mA 1000

hrs.

0/100

Steady State Operating Life of Low Temperature Ta=-40°C,

I F=30mA 1000

hrs.

0/100

Permanence of Marking JEITA ED-4701

500 501 Solvent : Isopropyl Alcohol

Solvent Temperature : 20 ~ 25°C

Dipping Time : 5 min.

1 time 0/22

Vibration JEITA ED-4701

400 403

100 ~ 2000 ~ 100Hz Sweep 4min.

200m/s2

3directions, 4cycles

48min. 0/10

Drop

75cm 3

times

0/10

Electrostatic Discharge JEITA ED-4701

300 304 R=1.5k?, C=100pF

Test Voltage=2kV

3 times

Negative/Positive

0/22

(2) CRITERIA FOR JUDGING DAMAGE

Criteria for Judgement

Item Symbol Test Conditions Min. Max.

Forward Voltage V F I F=30mA - U.S.L.*) 1.1

Luminous Intensity

Condition 1

I V I F=30mA L.S.L.**) 0.7 -

Luminous Intensity

Condition 2

I V I F=30mA L.S.L.**) 0.5 -

*) U.S.L. : Upper Standard Level **) L.S.L. : Lower Standard Level

These test items are judged by the criteria of Luminous Intensity Condition 2.

Nichia STSE-CC7196A

7.CAUTIONS

The LEDs are devices which are materialized by combining Blue LEDs and special phosphors. Consequently, the color of the LEDs is changed a little by an operating current.

Care should be taken after due consideration when using LEDs.

(1) Moisture Proof Package

· When moisture is absorbed into the SMT package it may vaporize and expand during soldering.

There is a possibility that this can cause exfoliation of the contacts and damage to the optical

characteristics of the LEDs. For this reason, the moisture proof package is used to keep moisture to a minimum in the package.

· The moisture proof package is made of an aluminum moisture proof bag. A package of

a moisture absorbent material (silica gel) is inserted into the aluminum moisture proof bag.

The silica gel changes its color from blue to pink as it absorbs moisture.

(2) Storage

· Storage Conditions

Before opening the package :

The LEDs should be kept at 30°C or less and 90%RH or less. The LEDs should be used within a

year. When storing the LEDs, moisture proof packaging with absorbent material (silica gel) is recommended.

After opening the package :

The LEDs should be kept at 30°C or less and 70%RH or less. The LEDs should be soldered

within 168 hours (7days) after opening the package. If unused LEDs remain, they should be

stored in moisture proof packages, such as sealed containers with packages of moisture absorbent

material (silica gel). It is also recommended to return the LEDs to the original moisture proof bag and to reseal the moisture proof bag again.

· If the moisture absorbent material (silica gel) has faded away or the LEDs have exceeded the storage time, baking treatment should be performed using the following conditions.

Baking treatment : more than 24 hours at 65 ± 5°C

· Nichia LED electrodes and leadframes are silver plated copper alloy. The silver surface may be affected by environments which contain corrosive substances. Please avoid conditions which may cause the LED to corrode, tarnish or discolor. This corrosion or discoloration might lower solderability or might

affect on optical characteristics.

· Please avoid rapid transitions in ambient temperature, especially in high humidity environments where

condensation can occur.

(3) Heat Generation

· Thermal design of the end product is of paramount importance. Please consider the heat generation of the LED when making the system design. The coefficient of temperature increase per input

electric power is affected by the thermal resistance of the circuit board and density of LED placement on the board, as well as other components. It is necessary to avoid intense heat generation and operate within the maximum ratings given in this specification.

· The operating current should be decided after considering the ambient maximum temperature of LEDs.

Nichia STSE-CC7196A

(4) Soldering Conditions

· The LEDs can be soldered in place using the reflow soldering method. Nichia cannot make a guarantee on the LEDs after they have been assembled using the dip soldering method. · Recommended soldering conditions

Reflow Soldering Hand Soldering

Lead Solder Lead-free Solder Pre-heat Pre-heat time Peak temperature Soldering time Condition 120 ~ 150°C 120 sec. Max. 240°C Max. 10 sec. Max. refer to

Temperature

- profile 1.

180 ~ 200°C 120 sec. Max. 260°C Max. 10 sec. Max. refer to Temperature - profile 2. (N 2 reflow is

recommended.)

Temperature Soldering time 350°C Max. 3 sec. Max. (one time only) Although the recommended soldering conditions are specified in the above table, reflow or hand soldering at the lowest possible temperature is desirable for the LEDs.

A rapid-rate process is not recommended for cooling the LEDs down from the peak temperature. [Temperature-profile (Surface of circuit board)] Use the conditions shown to the under figure.

[Recommended soldering pad design]

Use the following conditions shown in the figure.

· Occasionally there is a brightness decrease caused by the influence of heat or ambient atmosphere

during air reflow. It is recommended that the User use the nitrogen reflow method.

· The encapsulated material of the LEDs is silicone. Therefore the LEDs have a soft surface on the top of package. The pressure to the top surface will be influence to the reliability of the LEDs. Precautions should be taken to avoid the strong pressure on the encapsulated part. So when using the chip mounter, the picking up nozzle that does not affect the silicone resin should be used.

· Repairing should not be done after the LEDs have been soldered. When repairing is unavoidable, a double-head soldering iron should be used. It should be confirmed beforehand whether the characteristics of the LEDs will or will not be damaged by repairing. · Reflow soldering should not be done more than two times. · When soldering, do not put stress on the LEDs during heating. · After soldering, do not warp the circuit board.

60sec.Max.

Above 220°C

120sec.Max.

Pre-heating

260°C Max.

10sec. Max.

1~ 5°C / sec.

1~ 5°C / sec.

180 ~ 200°C <1 : Lead Solder>

<2 : Lead-free Solder>

60sec.Max. Above 200°C

120sec.Max.

Pre-heating

240°C Max.

10sec. Max.2.5 ~ 5°C / sec.

2.5 ~ 5°C / sec. 120 ~ 150°C : Solder resist

(Unit : mm)

Nichia STSE-CC7196A

(5) Cleaning

· It is recommended that isopropyl alcohol be used as a solvent for cleaning the LEDs. When using other solvents, it should be confirmed beforehand whether the solvents will dissolve the package and the resin or not. Freon solvents should not be used to clean the LEDs because of worldwide regulations. · Do not clean the LEDs by the ultrasonic. When it is absolutely necessary, the influence of ultrasonic cleaning on the LEDs depends on factors such as ultrasonic power and the assembled condition.

Before cleaning, a pre-test should be done to confirm whether any damage to the LEDs will occur.

(6) Static Electricity

· Static electricity or surge voltage damages the LEDs.

It is recommended that a wrist band or an anti-electrostatic glove be used when handling the LEDs.

· All devices, equipment and machinery must be properly grounded. It is recommended that precautions be taken against surge voltage to the equipment that mounts the LEDs.

· When inspecting the final products in which LEDs were assembled, it is recommended to check

whether the assembled LEDs are damaged by static electricity or not. It is easy to find

static-damaged LEDs by a light-on test or a VF test at a lower current (below 1mA is recommended). · Damaged LEDs will show some unusual characteristics such as the forward voltage becomes lower, or the LEDs do not light at the low current.

Criteria : (V F> 2.0V at I F=0.5mA)

(7) Others

· NSSW064 complies with RoHS Directive.

· The LED light output is strong enough to injure human eyes. Precautions must be taken to prevent looking directly at the LEDs with unaided eyes for more than a few seconds.

· Flashing lights have been known to cause discomfort in people; you can prevent this by taking

precautions during use. Also, people should be cautious when using equipment that has had LEDs incorporated into it.

· The LEDs described in this brochure are intended to be used for ordinary electronic equipment (such as office equipment, communications equipment, measurement instruments and household appliances).

Consult Nichia’s sales staff in advance for information on the applications in which exceptional quality and reliability are required, particularly when the failure or malfunction of the LEDs may directly

jeopardize life or health (such as for airplanes, aerospace, submersible repeaters, nuclear reactor

control systems, automobiles, traffic control equipment, life support systems and safety devices).

· User shall not reverse engineer by disassembling or analysis of the LEDs without having prior written consent from Nichia. When defective LEDs are found, the User shall inform Nichia directly before

disassembling or analysis.

· The formal specifications must be exchanged and signed by both parties before large volume purchase begins. · The appearance and specifications of the product may be modified for improvement without notice.

Nichia STSE-CC7196A

?Color Coordinates Measurement allowance is ± 0.01.

Nichia

STSE-CC7196A

Nichia

STSE-CC7196A

Nichia STSE-CC7196A

-11-

Nichia STSE-CC7196A

元器件交易网https://www.wendangku.net/doc/969684941.html,

Nichia STSE-CC7196A

相关文档