当前位置：文档库 › MC10H107MELG中文资料

MC10H107MELG中文资料

MC10H107

Triple 2?Input Exclusive OR/ Exclusive NOR Gate

Description

The MC10H107 is a triple 2?input exclusive OR/NOR gate. This MECL 10H? part is a functional/pinout duplication of the standard MECL 10K? family part, with 100% improvement in propagation delay, and no increase in power?supply current.

Features

?Propagation Delay, 1.0 ns Typical

?Power Dissipation 35 mW/Gate Typical (same as MECL 10K)?Improved Noise Margin 150 mV (Over Operating V oltage and Temperature Range)

?V oltage Compensated

?MECL 10K Compatible

?Pb?Free Packages are Available*

*For additional information on our Pb?Free strategy and soldering details, please download the ON Semiconductor Soldering and Mounting Techniques Reference Manual, SOLDERRM/D.

https://www.wendangku.net/doc/c37721819.html,

See detailed ordering and shipping information in the package dimensions section on page 3 of this data sheet.

ORDERING INFORMATION

Figure 1. Logic Diagram Figure 2. Pin Assignment

V CC1A out

A out A in A in *NC

B in V EE

V CC2C in C in C out C out B out B out B in

161514131211109

12345678

V CC1 = Pin 1V CC2 = Pin 16V EE = Pin 8

1494121011327

5*NC = No Connection

Pin assignment is for Dual ?in ?Line Package.

Table 1. MAXIMUM RATINGS

Symbol Characteristic

Rating Unit V EE Power Supply (V CC = 0)?8.0 to 0Vdc V I Input Voltage (V CC = 0)0 to V EE Vdc I out Output Current

Continuous

Surge

50100mA T A Operating Temperature Range 0 to +75°C T stg

Storage Temperature Range

Plastic Ceramic ?55 to +150?55 to +165

°C °C

Maximum ratings are those values beyond which device damage can occur. Maximum ratings applied to the device are individual stress limit values (not normal operating conditions) and are not valid simultaneously. If these limits are exceeded, device functional operation is not implied,damage may occur and reliability may be affected.

Table 2. ELECTRICAL CHARACTERISTICS (V EE = ?5.2 V ±5%) (Note 1)

0°

25°

75°

Symbol Characteristic

Min Max Min Max Min Max Unit I E Power Supply Current ?31?28?31mA I inH Input Current High ?425?265?265m A I inL Input Current Low 0.5?0.5?0.3?m A V OH High Output Voltage ?1.02?0.84?0.98?0.81?0.92?0.735Vdc V OL Low Output Voltage ?1.95?1.63?1.95?1.63?1.95?1.60Vdc V IH High Input Voltage ?1.17?0.84?1.13?0.81?1.07?0.735Vdc V IL

Low Input Voltage

?1.95

?1.48

?1.95

?1.48

?1.95

?1.45

Vdc

1.Each MECL 10H series circuit has been designed to meet the dc specifications shown in the test table, after thermal equilibrium has been established. The circuit is in a test socket or mounted on a printed circuit board and transverse air flow greater than 500 linear fpm is maintained. Outputs are terminated through a 50 W resistor to ?

2.0 V.

Table 3. AC CHARACTERISTICS

0°25°75°

Symbol Characteristic Min Max Min Max Min Max Unit

t pd Propagation Delay0.4 1.50.4 1.60.4 1.7ns

t r Rise Time0.5 1.50.5 1.60.5 1.7ns

t f Fall Time0.5 1.50.5 1.60.5 1.7ns NOTE:Device will meet the specifications after thermal equilibrium has been established when mounted in a test socket or printed circuit board with maintained transverse airflow greater than 500 lfpm. Electrical parameters are guaranteed only over the declared

operating temperature range. Functional operation of the device exceeding these conditions is not implied. Device specification limit values are applied individually under normal operating conditions and not valid simultaneously.

ORDERING INFORMATION

Device Package Shipping?

MC10H107FN PLLC?2046 Units / Rail

MC10H107FNG PLLC?20

(Pb?Free)46 Units / Rail

MC10H107FNR2PLLC?20500 / Tape & Reel

MC10H107FNR2G PLLC?20

(Pb?Free)500 / Tape & Reel

MC10H107L CDIP?1625 Unit / Rail

MC10H107M SOEIAJ?1650 Unit / Rail

MC10H107MG SOEIAJ?16

(Pb?Free)

50 Unit / Rail

MC10H107MEL SOEIAJ?162000 / Tape & Reel

MC10H107MELG SOEIAJ?16

(Pb?Free)

2000 / Tape & Reel

MC10H107P PDIP?1625 Unit / Rail

MC10H107PG PDIP?16

(Pb?Free)

25 Unit / Rail

?For information on tape and reel specifications, including part orientation and tape sizes, please refer to our Tape and Reel Packaging Specifications Brochure, BRD8011/D.

PACKAGE DIMENSIONS

L?M

S 0.010 (0.250) N

T 20 LEAD PLLC CASE 775?02ISSUE E

NOTES:

1.DIMENSIONS AND TOLERANCING PER ANSI Y14.5M,198

2.DIMENSIONS IN INCHES.

3.DATUMS ?L ?, ?M ?, AND ?N ? DETERMINED WHERE TOP OF LEAD SHOULDER EXITS PLASTIC BODY AT MOLD PARTING LINE.

4.DIMENSION G1, TRUE POSITION TO BE MEASURED AT DATUM ?T ?, SEATING PLANE.

5.DIMENSIONS R AND U DO NOT INCLUDE MOLD FLASH.ALLOWABLE MOLD FLASH IS 0.010 (0.250) PER SIDE.

6.DIMENSIONS IN THE PACKAGE TOP MAY BE SMALLER THAN THE PACKAGE BOTTOM BY UP TO 0.012 (0.300).DIMENSIONS R AND U ARE DETERMINED AT THE OUTERMOST EXTREMES OF THE PLASTIC BODY EXCLUSIVE OF MOLD FLASH, TIE BAR BURRS, GATE BURRS AND INTERLEAD FLASH, BUT INCLUDING ANY MISMATCH BETWEEN THE TOP AND BOTTOM OF THE PLASTIC BODY .

7.DIMENSION H DOES NOT INCLUDE DAMBAR PROTRUSION OR INTRUSION. THE DAMBAR

PROTRUSION(S) SHALL NOT CAUSE THE H DIMENSION TO BE GREATER THAN 0.037 (0.940). THE DAMBAR

INTRUSION(S) SHALL NOT CAUSE THE H DIMENSION TO BE SMALLER THAN 0.025 (0.635).

DIM MIN MAX MIN MAX MILLIMETERS

INCHES A 0.3850.3959.7810.03B 0.3850.3959.7810.03C 0.1650.180 4.20 4.57E 0.0900.110 2.29 2.79F 0.0130.0190.330.48G 0.050 BSC 1.27 BSC H 0.0260.0320.660.81J 0.020???0.51???K 0.025???0.64???R 0.3500.3568.899.04U 0.3500.3568.899.04V 0.0420.048 1.07 1.21W 0.0420.048 1.07 1.21X 0.0420.056 1.07 1.42Y ???0.020???0.50Z 2 10 2 10 G10.3100.3307.888.38K1

0.040??? 1.02???

____

PACKAGE DIMENSIONS

SOEIAJ ?16CASE 966?01ISSUE A

NOTES:

1.DIMENSIONING AND TOLERANCING PER ANSI Y14.5M, 198

CDIP ?16L SUFFIX

CERAMIC DIP PACKAGE

CASE 620A ?01NOTES:

1.DIMENSIONING AND TOLERANCING PER ASME Y14.5M, 1994.

2.CONTROLLING DIMENSION: INCH.

3.DIMENSION L TO CENTER OF LEAD WHEN FORMED PARALLEL.

4.DIMENSION F MAY NARROW TO 0.76 (0.030)WHERE THE LEAD ENTERS THE CERAMIC BODY.

5THIS DRAWING REPLACES OBSOLETE CASE OUTLINE 620?10.

0.25 (0.010)

T DIM MIN MAX MIN MAX MILLIMETERS

INCHES A 0.7500.78519.0519.93B 0.2400.295 6.107.49C ???0.200??? 5.08D 0.0150.0200.390.50E 0.050 BSC 1.27 BSC F 0.0550.065 1.40 1.65G 0.100 BSC 2.54 BSC H 0.0080.0150.210.38K 0.1250.170 3.18 4.31L 0.300 BSC 7.62 BSC M 0 15 0 15 N

0.0200.040

0.51 1.01

____

PACKAGE DIMENSIONS

NOTES:

1.DIMENSIONING AND TOLERANCING PER ANSI Y14.5M, 198

2.CONTROLLING DIMENSION: INCH.

3.DIMENSION L TO CENTER OF LEADS WHEN FORMED PARALLEL.

4.DIMENSION B DOES NOT INCLUDE MOLD FLASH.

5.ROUNDED CORNERS OPTIONAL.

DIM MIN MAX MIN MAX MILLIMETERS

INCHES A 0.7400.77018.8019.55B 0.2500.270 6.35 6.85C 0.1450.175 3.69 4.44D 0.0150.0210.390.53F 0.0400.70 1.02 1.77G 0.100 BSC 2.54 BSC H 0.050 BSC 1.27 BSC J 0.0080.0150.210.38K 0.1100.130 2.80 3.30L 0.2950.3057.507.74M 0 10 0 10 S

0.0200.040

0.51 1.01

____PDIP ?16P SUFFIX

PLASTIC DIP PACKAGE

ON Semiconductor and are registered trademarks of Semiconductor Components Industries, LLC (SCILLC). SCILLC reserves the right to make changes without further notice to any products herein. SCILLC makes no warranty, representation or guarantee regarding the suitability of its products for any particular purpose, nor does SCILLC assume any liability arising out of the application or use of any product or circuit, and specifically disclaims any and all liability, including without limitation special, consequential or incidental damages.“Typical” parameters which may be provided in SCILLC data sheets and/or specifications can and do vary in different applications and actual performance may vary over time. All operating parameters, including “Typicals” must be validated for each customer application by customer’s technical experts. SCILLC does not convey any license under its patent rights nor the rights of others. SCILLC products are not designed, intended, or authorized for use as components in systems intended for surgical implant into the body, or other applications intended to support or sustain life, or for any other application in which the failure of the SCILLC product could create a situation where personal injury or death may occur. Should Buyer purchase or use SCILLC products for any such unintended or unauthorized application, Buyer shall indemnify and hold SCILLC and its officers, employees, subsidiaries, affiliates,and distributors harmless against all claims, costs, damages, and expenses, and reasonable attorney fees arising out of, directly or indirectly, any claim of personal injury or death associated with such unintended or unauthorized use, even if such claim alleges that SCILLC was negligent regarding the design or manufacture of the part. SCILLC is an Equal Opportunity/Affirmative Action Employer. This literature is subject to all applicable copyright laws and is not for resale in any manner.

PUBLICATION ORDERING INFORMATION

MECL 10H and MECL 10K are trademarks of Motorola, Inc.