ADC0808-9
ADC0808/ADC0809
8-Bit μP Compatible A/D Converters with 8-Channel Multiplexer
General Description
The ADC0808,ADC0809data acquisition component is a monolithic CMOS device with an 8-bit analog-to-digital con-verter,8-channel multiplexer and microprocessor compatible control logic.The 8-bit A/D converter uses successive ap-proximation as the conversion technique.The converter fea-tures a high impedance chopper stabilized comparator,a 256R voltage divider with analog switch tree and a succes-sive approximation register.The 8-channel multiplexer can directly access any of 8-single-ended analog signals.The device eliminates the need for external zero and full-scale adjustments.Easy interfacing to microprocessors is provided by the latched and decoded multiplexer address inputs and latched TTL TRI-STATE ?outputs.
The design of the ADC0808,ADC0809has been optimized by incorporating the most desirable aspects of several A/D conversion techniques.The ADC0808,ADC0809offers high speed,high accuracy,minimal temperature dependence,ex-cellent long-term accuracy and repeatability,and consumes minimal power.These features make this device ideally suited to applications from process and machine control to consumer and automotive applications.For 16-channel mul-tiplexer with common output (sample/hold port)see ADC0816data sheet.(See AN-247for more information.)
Features
n Easy interface to all microprocessors
n Operates ratiometrically or with 5V DC or analog span adjusted voltage reference
n No zero or full-scale adjust required n 8-channel multiplexer with address logic
n 0V to 5V input range with single 5V power supply n Outputs meet TTL voltage level specifications n Standard hermetic or molded 28-pin DIP package n 28-pin molded chip carrier package n ADC0808equivalent to MM74C949n ADC0809equivalent to MM74C949-1
Key Specifications
n Resolution
8Bits
n Total Unadjusted Error ±1?2
LSB and ±1LSB
n Single Supply 5V DC n Low Power
15mW n
Conversion Time
100μs
Block Diagram
TRI-STATE ?is a registered trademark of National Semiconductor Corp.
DS005672-1
See Ordering Information
June 1999
ADC0808/ADC08098-Bit μP Compatible A/D Converters with 8-Channel Multiplexer
?1999National Semiconductor Corporation https://www.wendangku.net/doc/c49911426.html,
Connection Diagrams
Ordering Information
TEMPERATURE RANGE ?40?C to +85?C
?55?C to +125?C Error
±1?2LSB Unadjusted ADC0808CCN ADC0808CCV ADC0808CCJ
ADC0808CJ
±1LSB Unadjusted
ADC0809CCN ADC0809CCV
Package Outline
N28A Molded DIP
V28A Molded Chip Carrier
J28A Ceramic DIP
J28A Ceramic DIP
Dual-In-Line Package
DS005672-11
Order Number ADC0808CCN or ADC0809CCN
See NS Package J28A or N28A
Molded Chip Carrier Package
DS005672-12
Order Number ADC0808CCV or ADC0809CCV
See NS Package V28A
https://www.wendangku.net/doc/c49911426.html, 2
Absolute Maximum Ratings(Notes2,1) If Military/Aerospace specified devices are required, please contact the National Semiconductor Sales Office/ Distributors for availability and specifications.
Supply Voltage(V CC)(Note3) 6.5V Voltage at Any Pin?0.3V to(V CC+0.3V) Except Control Inputs
Voltage at Control Inputs?0.3V to+15V (START,OE,CLOCK,ALE,ADD A,ADD B,ADD C) Storage Temperature Range?65?C to+150?C Package Dissipation at T A=25?C875mW Lead Temp.(Soldering,10seconds)
Dual-In-Line Package(plastic)260?C
Dual-In-Line Package(ceramic)300?C Molded Chip Carrier Package
Vapor Phase(60seconds)215?C Infrared(15seconds)220?C ESD Susceptibility(Note8)400V
Operating Conditions(Notes1,2) Temperature Range(Note1)T MIN≤T A≤T MAX ADC0808CCN,ADC0809CCN?40?C≤T A≤+85?C ADC0808CCV,ADC0809CCV?40?C≤T A≤+85?C Range of V CC(Note1) 4.5V DC to6.0V DC
Electrical Characteristics
Converter Specifications:V CC=5V DC=V REF+,V REF(?)=GND,T MIN≤T A≤T MAX and f CLK=640kHz unless otherwise stated.
Symbol Parameter Conditions Min Typ Max Units ADC0808
Total Unadjusted Error25?C±1?2LSB
(Note5)T MIN to T MAX±3?4LSB
ADC0809
Total Unadjusted Error0?C to70?C±1LSB
(Note5)T MIN to T MAX±11?4LSB
Input Resistance From Ref(+)to Ref(?) 1.0 2.5k?
Analog Input Voltage Range(Note4)V(+)or V(?)GND?0.10V CC+0.10V DC
V REF(+)Voltage,Top of Ladder Measured at Ref(+)V CC V CC+0.1V Voltage,Center of Ladder V CC/2-0.1V CC/2V CC/2+0.1V
V REF(?)Voltage,Bottom of Ladder Measured at Ref(?)?0.10V
I IN Comparator Input Current f c=640kHz,(Note6)?2±0.52μA Electrical Characteristics
Digital Levels and DC Specifications:ADC0808CCN,ADC0808CCV,ADC0809CCN and ADC0809CCV,4.75≤V CC≤5.25V,
?40?C≤T A≤+85?C unless otherwise noted
Symbol Parameter Conditions Min Typ Max Units ANALOG MULTIPLEXER
I OFF(+)OFF Channel Leakage Current V CC=5V,V IN=5V,
T A=25?C10200nA
T MIN to T MAX 1.0μA
I OFF(?)OFF Channel Leakage Current V CC=5V,V IN=0,
T A=25?C?200?10nA
T MIN to T MAX?1.0μA CONTROL INPUTS
V IN(1)Logical“1”Input Voltage V CC?1.5V
V IN(0)Logical“0”Input Voltage 1.5V
I IN(1)Logical“1”Input Current V IN=15V 1.0μA
(The Control Inputs)
I IN(0)Logical“0”Input Current V IN=0?1.0μA
(The Control Inputs)
I CC Supply Current f CLK=640kHz0.3 3.0mA DATA OUTPUTS AND EOC(INTERRUPT)
V OUT(1)Logical“1”Output Voltage I O=?360μA V CC?0.4V
https://www.wendangku.net/doc/c49911426.html,
3
Electrical Characteristics(Continued)
Digital Levels and DC Specifications:ADC0808CCN,ADC0808CCV,ADC0809CCN and ADC0809CCV,4.75≤V CC≤5.25V,?40?C≤T A≤+85?C unless otherwise noted
Symbol Parameter Conditions Min Typ Max Units DATA OUTPUTS AND EOC(INTERRUPT)
V OUT(0)Logical“0”Output Voltage I O=1.6mA0.45V
V OUT(0)Logical“0”Output Voltage EOC I O=1.2mA0.45V
I OUT TRI-STATE Output Current V O=5V3μA
V O=0?3μA Electrical Characteristics
Timing Specifications V CC=V REF(+)=5V,V REF(?)=GND,t r=t f=20ns and T A=25?C unless otherwise noted.
Symbol Parameter Conditions MIn Typ Max Units t WS Minimum Start Pulse Width(Figure5)100200ns
t WALE Minimum ALE Pulse Width(Figure5)100200ns
t s Minimum Address Set-Up Time(Figure5)2550ns
t H Minimum Address Hold Time(Figure5)2550ns
t D Analog MUX Delay Time R S=0?(Figure5)1 2.5μs From ALE
t H1,t H0OE Control to Q Logic State C L=50pF,R L=10k(Figure8)125250ns
t1H,t0H OE Control to Hi-Z C L=10pF,R L=10k(Figure8)125250ns
t c Conversion Time f c=640kHz,(Figure5)(Note7)90100116μs
f c Clock Frequency106401280kHz t EOC EOC Delay Time(Figure5)08+2μS Clock
Periods C IN Input Capacitance At Control Inputs1015pF
C OUT TRI-STATE Output At TRI-STATE Outputs1015pF
Capacitance
Note1:Absolute Maximum Ratings indicate limits beyond which damage to the device may occur.DC and AC electrical specifications do not apply when operating the device beyond its specified operating conditions.
Note2:All voltages are measured with respect to GND,unless othewise specified.
Note3:A zener diode exists,internally,from V CC to GND and has a typical breakdown voltage of7V DC.
Note4:Two on-chip diodes are tied to each analog input which will forward conduct for analog input voltages one diode drop below ground or one diode drop greater than the V CC n supply.The spec allows100mV forward bias of either diode.This means that as long as the analog V IN does not exceed the supply voltage by more than100mV,the output code will be correct.To achieve an absolute0V DC to5V DC input voltage range will therefore require a minimum supply voltage of4.900V DC over temperature variations,initial tolerance and loading.
Note5:Total unadjusted error includes offset,full-scale,linearity,and multiplexer errors.See Figure3.None of these A/Ds requires a zero or full-scale adjust.How-ever,if an all zero code is desired for an analog input other than0.0V,or if a narrow full-scale span exists(for example:0.5V to4.5V full-scale)the reference voltages can be adjusted to achieve this.See Figure13.
Note6:Comparator input current is a bias current into or out of the chopper stabilized comparator.The bias current varies directly with clock frequency and has little temperature dependence(Figure6).See paragraph4.0.
Note7:The outputs of the data register are updated one clock cycle before the rising edge of EOC.
Note8:Human body model,100pF discharged through a1.5k?resistor.
https://www.wendangku.net/doc/c49911426.html,4
Functional Description
Multiplexer.The device contains an8-channel single-ended analog signal multiplexer.A particular input channel is se-lected by using the address decoder.Table1shows the input states for the address lines to select any channel.The ad-dress is latched into the decoder on the low-to-high transition of the address latch enable signal.
TABLE1.
SELECTED ADDRESS LINE
ANALOG
CHANNEL
C B A
IN0L L L
IN1L L H
IN2L H L
IN3L H H
IN4H L L
IN5H L H
IN6H H L
IN7H H H CONVERTER CHARACTERISTICS
The Converter
The heart of this single chip data acquisition system is its 8-bit analog-to-digital converter.The converter is designed to give fast,accurate,and repeatable conversions over a wide range of temperatures.The converter is partitioned into3 major sections:the256R ladder network,the successive ap-proximation register,and the comparator.The converter’s digital outputs are positive true.
The256R ladder network approach(Figure1)was chosen over the conventional R/2R ladder because of its inherent monotonicity,which guarantees no missing digital codes. Monotonicity is particularly important in closed loop feedback control systems.A non-monotonic relationship can cause os-cillations that will be catastrophic for the system.Additionally, the256R network does not cause load variations on the ref-erence voltage.
The bottom resistor and the top resistor of the ladder net-
work in Figure1are not the same value as the remainder of
the network.The difference in these resistors causes the
output characteristic to be symmetrical with the zero and
full-scale points of the transfer curve.The first output transi-
tion occurs when the analog signal has reached+1?2LSB
and succeeding output transitions occur every1LSB later up
to full-scale.
The successive approximation register(SAR)performs8it-
erations to approximate the input voltage.For any SAR type
converter,n-iterations are required for an n-bit converter.
Figure2shows a typical example of a3-bit converter.In the
ADC0808,ADC0809,the approximation technique is ex-
tended to8bits using the256R network.
The A/D converter’s successive approximation register
(SAR)is reset on the positive edge of the start conversion
(SC)pulse.The conversion is begun on the falling edge of
the start conversion pulse.A conversion in process will be in-
terrupted by receipt of a new start conversion pulse.Con-
tinuous conversion may be accomplished by tying the
end-of-conversion(EOC)output to the SC input.If used in
this mode,an external start conversion pulse should be ap-
plied after power up.End-of-conversion will go low between
0and8clock pulses after the rising edge of start conversion.
The most important section of the A/D converter is the com-
parator.It is this section which is responsible for the ultimate
accuracy of the entire converter.It is also the comparator
drift which has the greatest influence on the repeatability of
the device.A chopper-stabilized comparator provides the
most effective method of satisfying all the converter require-
ments.
The chopper-stabilized comparator converts the DC input
signal into an AC signal.This signal is then fed through a
high gain AC amplifier and has the DC level restored.This
technique limits the drift component of the amplifier since the
drift is a DC component which is not passed by the AC am-
plifier.This makes the entire A/D converter extremely insen-
sitive to temperature,long term drift and input offset errors.
Figure4shows a typical error curve for the ADC0808as
measured using the procedures outlined in AN-179.
https://www.wendangku.net/doc/c49911426.html, 5
Functional Description
(Continued)
DS005672-2
FIGURE 1.Resistor Ladder and Switch Tree
DS005672-13
FIGURE 2.3-Bit A/D Transfer Curve
DS005672-14
FIGURE 3.3-Bit A/D Absolute Accuracy Curve
DS005672-15
FIGURE 4.Typical Error Curve
https://www.wendangku.net/doc/c49911426.html, 6
Timing Diagram
DS005672-4
FIGURE5.
7
https://www.wendangku.net/doc/c49911426.html,
Typical Performance Characteristics
TRI-STATE Test Circuits and Timing Diagrams
Applications Information
OPERATION
1.0RATIOMETRIC CONVERSION
The ADC0808,ADC0809is designed as a complete Data Acquisition System (DAS)for ratiometric conversion sys-tems.In ratiometric systems,the physical variable being measured is expressed as a percentage of full-scale which is not necessarily related to an absolute standard.The voltage input to the ADC0808is expressed by the equation
(1)
V IN =Input voltage into the ADC0808V fs =Full-scale voltage V Z =Zero voltage
D X =Data point being measured D MAX =Maximum data limit D MIN =Minimum data limit
A good example of a ratiometric transducer is a potentiom-eter used as a position sensor.The position of the wiper is di-rectly proportional to the output voltage which is a ratio of the full-scale voltage across it.Since the data is represented as a proportion of full-scale,reference requirements are greatly reduced,eliminating a large source of error and cost for many applications.A major advantage of the ADC0808,ADC0809is that the input voltage range is equal to the sup-ply range so the transducers can be connected directly across the supply and their outputs connected directly into the multiplexer inputs,(Figure 9).
Ratiometric transducers such as potentiometers,strain gauges,thermistor bridges,pressure transducers,etc.,are suitable for measuring proportional relationships;however,many types of measurements must be referred to an abso-lute standard such as voltage or current.This means a sys-DS005672-16
FIGURE https://www.wendangku.net/doc/c49911426.html,parator I IN vs V IN
(V CC =V REF =5V)
DS005672-17
FIGURE 7.Multiplexer R ON vs V IN
(V CC =V REF =5V)
t 1H ,t H1
DS005672-18
t 1H ,C L =10pF
DS005672-19t H1,C L =50pF
DS005672-20
t 0H ,t H0DS005672-21
t 0H ,C L =10pF DS005672-22
t H0,C L =50pF
DS005672-23
FIGURE 8.
https://www.wendangku.net/doc/c49911426.html,
8
Applications Information(Continued)
tem reference must be used which relates the full-scale volt-age to the standard volt.For example,if V CC=V REF=5.12V, then the full-scale range is divided into256standard steps. The smallest standard step is1LSB which is then20mV.
2.0RESISTOR LADDER LIMITATIONS
The voltages from the resistor ladder are compared to the selected into8times in a conversion.These voltages are coupled to the comparator via an analog switch tree which is referenced to the supply.The voltages at the top,center and bottom of the ladder must be controlled to maintain proper operation.The top of the ladder,Ref(+),should not be more positive than the supply,and the bottom of the ladder,Ref(?),should not be more negative than ground.The center of the ladder voltage must also be near the center of the supply because the analog switch tree changes from N-channel switches to P-channel switches.These limitations are automatically sat-isfied in ratiometric systems and can be easily met in ground referenced systems.
Figure10shows a ground referenced system with a sepa-rate supply and reference.In this system,the supply must be trimmed to match the reference voltage.For instance,if a 5.12V is used,the supply should be adjusted to the same voltage within0.1V.
The ADC0808needs less than a milliamp of supply current so developing the supply from the reference is readily ac-complished.In Figure11a ground referenced system is shown which generates the supply from the reference.The buffer shown can be an op amp of sufficient drive to supply the milliamp of supply current and the desired bus drive,or if a capacitive bus is driven by the outputs a large capacitor will supply the transient supply current as seen in Figure12.The LM301is overcompensated to insure stability when loaded by the10μF output capacitor.The top and bottom ladder voltages cannot exceed V CC and ground,respectively,but they can be symmetrically less than V CC and greater than ground.The center of the ladder volt-age should always be near the center of the supply.The sen-sitivity of the converter can be increased,(i.e.,size of the LSB steps decreased)by using a symmetrical reference sys-tem.In Figure13,a2.5V reference is symmetrically cen-tered about V CC/2since the same current flows in identical resistors.This system with a2.5V reference allows the LSB bit to be half the size of a5V reference system.
DS005672-7
FIGURE9.Ratiometric Conversion System
https://www.wendangku.net/doc/c49911426.html,
9
Applications Information(Continued)
DS005672-24
FIGURE10.Ground Referenced
Conversion System Using Trimmed Supply
DS005672-25
FIGURE11.Ground Referenced Conversion System with
Reference Generating V CC Supply
https://www.wendangku.net/doc/c49911426.html,10
Applications Information(Continued)
3.0CONVERTER EQUATIONS
The transition between adjacent codes N and N+1is given
by:
(2)
The center of an output code N is given by:
(3)
The output code N for an arbitrary input are the integers
within the range:
(4)
Where:V IN=Voltage at comparator input
V REF(+)=Voltage at Ref(+)
V REF(?)=Voltage at Ref(?)
V TUE=Total unadjusted error voltage(typically
V REF(+)÷512)
DS005672-26
FIGURE12.Typical Reference and Supply Circuit
DS005672-27
R A=R B
*Ratiometric transducers
FIGURE13.Symmetrically Centered Reference
https://www.wendangku.net/doc/c49911426.html,
11
Applications Information
(Continued)
4.0ANALOG COMPARATOR INPUTS
The dynamic comparator input current is caused by the pe-riodic switching of on-chip stray capacitances.These are connected alternately to the output of the resistor ladder/switch tree network and to the comparator input as part of the operation of the chopper stabilized comparator.
The average value of the comparator input current varies di-rectly with clock frequency and with V IN as shown in Figure 6.
If no filter capacitors are used at the analog inputs and the signal source impedances are low,the comparator input cur-rent should not introduce converter errors,as the transient created by the capacitance discharge will die out before the comparator output is strobed.
If input filter capacitors are desired for noise reduction and signal conditioning they will tend to average out the dynamic comparator input current.It will then take on the characteris-tics of a DC bias current whose effect can be predicted con-ventionally.
Typical Application
TABLE 2.Microprocessor Interface Table
PROCESSOR READ WRITE INTERRUPT (COMMENT)8080MEMR
MEMW INTR (Thru RST Circuit)8085RD WR INTR (Thru RST Circuit)Z-80RD WR INT (Thru RST Circuit,Mode 0)SC/MP NRDS NWDS SA (Thru Sense A)6800
VMA ?φ2?R/W
VMA ?φ?R/W
IRQA or IRQB (Thru PIA)
DS005672-10
*Address latches needed for 8085and SC/MP interfacing the ADC0808to a microprocessor
https://www.wendangku.net/doc/c49911426.html, 12
Physical Dimensions inches(millimeters)unless otherwise noted
Molded Dual-In-Line Package(N)
Order Number ADC0808CCN or ADC0809CCN
NS Package Number N28B
Molded Chip Carrier(V)
Order Number ADC0808CCV or ADC0809CCV
NS Package Number V28A
13
https://www.wendangku.net/doc/c49911426.html,
Notes
LIFE SUPPORT POLICY
NATIONAL’S PRODUCTS ARE NOT AUTHORIZED FOR USE AS CRITICAL COMPONENTS IN LIFE SUPPORT DEVICES OR SYSTEMS WITHOUT THE EXPRESS WRITTEN APPROVAL OF THE PRESIDENT AND GENERAL COUNSEL OF NATIONAL SEMICONDUCTOR CORPORATION.As used herein:1.Life support devices or systems are devices or systems which,(a)are intended for surgical implant into the body,or (b)support or sustain life,and whose failure to perform when properly used in accordance with instructions for use provided in the labeling,can be reasonably expected to result in a significant injury to the user.
2.A critical component is any component of a life support device or system whose failure to perform can be reasonably expected to cause the failure of the life support device or system,or to affect its safety or effectiveness.
National Semiconductor Corporation Americas
Tel:1-800-272-9959Fax:1-800-737-7018Email:support@https://www.wendangku.net/doc/c49911426.html,
National Semiconductor Europe
Fax:+49(0)180-5308586Email:europe.support@https://www.wendangku.net/doc/c49911426.html,
Deutsch Tel:+49(0)180-5308585English Tel:+49(0)180-5327832Fran?ais Tel:+49(0)180-5329358Italiano Tel:+49(0)180-5341680
National Semiconductor Asia Pacific Customer Response Group Tel:65-2544466Fax:65-2504466
Email:sea.support@https://www.wendangku.net/doc/c49911426.html,
National Semiconductor Japan Ltd.
Tel:81-3-5639-7560Fax:81-3-5639-7507
https://www.wendangku.net/doc/c49911426.html,
A D C 0808/A D C 08098-
B i t μP
C o m p a t i b l e A /
D C o n v e r t e r s w i t h 8-C h a n n e l M u l t i p l e x e r
National does not assume any responsibility for use of any circuitry described,no circuit patent licenses are implied and National reserves the right at any time without notice to change said circuitry and specifications.
í???ê?ò??????ò1?′óμ?×ó°?o????DD?Dí?óòμ1¤3ì??ê?è??±μ?μ?×ó??ê?ó|ó??÷òa?úèYóD?÷?t×êá?μ?×ó??ê??§3?·t??×aè?oíòy??μèD??￠
°?è¨ê??-×÷??
在使用本资料或软件时欢迎到网站内的ＢＢＳ
中发表
技术论坛
欢迎到网站下载
电子爱好者ｈｔｔｐ：／／ｗｗｗ．ｅｔｕｎｉ．ｃｏｍ