机械专业英语试题及答案

课程机械工程专业英语

课程性质（□必修□限选□任选）考试方式（□闭卷□开卷）

一、选择题（在每题四个备选答案中选出一个正确答案，本大题共15小题，每小题1分，总计15分）

1. If all points in a linkage move in parallel planes the system undergoes planar motion and the linkage may be described as a .

A. planar motion

B. planar linkage

C. joints

D. slide

2. Though frame material and design should handle damping, are sometimes built into frame sections to handle specific problems.

A .beams B. holes C. dampers D. screw

3. The maximum allowable deflection of a shaft ______ determined by critical speed, gear, or bearing requirements.

A. often

B. must

C. was

D. is usually

4. We will have to _____ to better and better solutions as we generate more information.

A. repeat many times

B. iterating

C. iterate

D. try ways

5. If a product configuration is _______ specified and then examined to determine whether the performance requirements are met.

A. finally

B. tentatively

C. temporary

D. have been

6. Manufacturing can be defined as the _____ of raw materials into useful products through the use of the easiest and lest-expensive methods.

A. transformation

B. processing

C. process

D. transforming

7. The planer and knee types of milling machine is _____ because of its flexibility.

A. used most commonly

B. most popular

C. the most commonly used

D. most powerful

8. As a result, the system will vibrate at the frequency of the _____ force regardless of the initial conditions or natural frequency of the system.

A. action

B. excitation

C. out

D. act

9. Before two components are assembled together, the relationship between the dimensions of the mating surfaces_______.

A. must be giving out

B. should printed clearly

C. must be specified

D. should be clearly noted

10. The main practical advantage of lower pairs is their better ability to trap lubricant between their ______ surfaces.

A. enveloping

B. mating

C. outer

D. outside

11. The word______ itself usually refers to the deterioration of metals and ceramics, while similar phenomena in plastics generally called ______.

A. recrystallization…. corrosion

B. recrystallization…degradation

C. degradation…corrosion

D. corrosion… degradation

12. Most frames _______ cast iron, weld steel, composition, or concrete.

A. are made from

B. are made up of

C. was produced by

D. was consist of

13. Rotating shafts particularly those that run at high speeds, must be designed to avoid operation

at speeds.

A . low

B .overload C. critical D. hollow

14. Although cast iron is a fairly cheap material, each casting requires a .

A. pattern

B. model

C. mold

D. patent

15. The term is used to describe joints with surface contact, as with a pin surrounded by a hole.

A. high pair

B. low pair

C. surface pair

D. rotary pair

二、完型填空（在每个小题四个备选答案中选出一个正确答案，本大题共15小题，每小题1分，总计15分）

The term shaft usually refers to a relatively long member of round cross section that rotates and transmits power. One or more members such as gears, sprockets, pulleys, and cams are usually (16) to the shaft by means of pins, keys, splines, snap rings, and other devices. These latter members are among the “associated parts” considered in this text, as are couplings and universal joint, which serve to (17) the shaft to the source of power or load.

A shaft can have a noround cross section, ant it need not necessarily rotate. It can be stationary and

serve to (18) a rotating member, such as the short shafts that support the nondriving wheels of an automobile. The shafts supporting(19) gears can be either rotating or stationary depending on (20) the gear is attached to the shaft or supported by it through bearings.

It is apparent that shafts can be subjected to various combinations of axial, bending, and(21) loads, and that these loads may be static or fluctuating. Typically, a rotating shaft transmitting power is

(22) to a constant torque (producing a mean torsional stress) together with a completely reversed

bending load (producing an alternating bending stress).

In addition to satisfying (23) requirements, shafts must be designed so that deflections are within acceptable limits. Excessive (24) shafts deflection can hamper gear performance and cause (25) noise. The associated angular deflection can be very destructive to no-self- aligning bearings(either plain or rolling). (26) deflection can affect the accuracy of a cam or gear driven mechanism.

Furthermore, the greater the flexibility -either lateral or torsional-the lower the corresponding (27) speed.

考生注意：考试时间120 分钟试卷总分100 分共 5 页第 1 页

Sometimes members like gears and cams are made (28) with shaft, but more

often such members (which also include pulleys, sprockets, etc)are made

separately and then(29) shaft. The portion of the mounted member in contact

with the shaft is the hub. Attachment of the hub to the shaft is made in variety of

ways. A gear can be gripped (30) between a shoulder on the shaft and a spacer,

with torque being transmitted through a key. The grooves in the shaft and hub into

which the key fits are called keyways.

16、A) cement B) attached C) connected D) concrete

17、A) endure B) transmit C) serve D) connect

18、A) support B) meet C) satisfy D) strong

19、A) aims B) idler C) terminal D) tomb

20、A) due to B) weather C) whether D) for

21、A) elasticity B) torsional C) inertia D) acceleration

22、A) subjected B)…connect C) and D) From

23、A) deeply B) strength C) clearly understand D) long time

24、A) identify B) cross C) round D) lateral

25、A) lucrative B) objectionable C) attractable D) terrible

26、A) Moment B)Torment C) Torsional D) Movement

27、A) high B) critical C) first D) important

28、A) work B) idealization C) integral D) simplification

29、A) mounted onto B) refers C) referring to D) indicates

30、A) deformations B) bending limits C) laternal D) axially

三、阅读理解（在每个小题四个备选答案中选出一个正确答案，填在题头的表中）（本大题

共20小题，每小题2分，总计40分）

Text 1

Engineering design is a systematic process by which solution to the needs of humankind are obtained .The process is applied to problems(needs) of varying complexity .For example, mechanical engineers will use the design process to find an effective, efficient method to convert reciprocating motion to circular motion for the drive train in an intnternal combustion engine;

electrical engineers will use the process to design electrical generating systems using falling water as the power source; and materials engineers use the process to design ablative materials which enable astronaut s to safely reenter the earth’s atmosphere.

The vast majority of complex problems in today’s high technology society depend for solution not on a single engineering discipline, but on teams of engineers, scientists, environmentalists, economists, sociologists, and legal personnel. Solutions are not only dependent regulations and political influence. As engineers we are empowered with the technical expertise to develop new and improved products and systems, but at the same time we must be increasingly aware of the impact of our actions on society and the environment in general and work conscientiously toward the best solution in view of all relevant factors.

Design is the culmination of engineering educational process; it is the salient feature that distinguishes engineering design is found in the curriculum guidelines of the Accreditation Board for Engineering and Technology(ABET).ABET accredits curricula in engineering schools and derives its membership from the various engineering professional societies. Each accredited curriculum has a well-defined design component which falls within the ABET statement on design 订

线

read as follows.

Engineering design is the process of devising a system, component, or process to meet desired needs. It is decision making process(often iterative),in which the basic sciences, mathematics, and engineering sciences are applied to convert resources optimally to meet a sated objectives and criteria, synthesis, analysis, construction ,testing, and evaluation. The engineering design component of a curriculum must include most of the following features : development of student creativity, use of open-ended problem statement and use of modern design theory and methodology, formulation of design problem statement and specification, consideration of alternative solutions, feasibility considerations, production process, concurrent engineering design, and detailed system descriptions. Further, it is essential to include a variety of realistic constraints such as economic factors, safety, reliability, aesthetics, ethics, and social impact.

31、what’s the main meaning of message (1)?

A) Engineering design is a systematic process B) materials engineer’s main work

C) mechanical engineer’s has good idea D) electrical engineer’ main duty

32、In the author’s opinion, the design process is very complex and should taken into account many factors, from the

message who should NOT join into the design team _______.

A) environmentalists,

B) sociologists

C) engineers

D) Government officials

33、From the message, we can know the meaning of words “ABET”(at line third paragraph) is _____.

A) a set of accredits standard

B) a kind of design method

C) a department of US government which responsible for engineering design

D) A set of law

34、It can be concluded from the passage that in the exercise and training of student, which character of the following is

NOT included in the curriculum ______.

A) creativity

B) new material

C) ethics

D) economic factors

35、The title of the message is ______.

A) the roles of engineers in manufacturing

B) the importance of mechanical design

C) engineering design

D) The process of machine design

TEXT 2

Working drawings are the complete set of standardized drawings specifying the manufacture and assembly of a product based on its design. The complexity of the design determines the number and types of drawings. Working drawings may be on more than one sheet and may contain written instructions called specifications.

Working drawings are blueprints used for manufacturing products. Therefore, the set of drawings must:(a) completely describe the parts, both visually and dimensionally;(b)show the parts in assembly;(3)identify all the parts; and (4)specify standard parts. The graphics and text information must be sufficiently complete and accurate to manufacture and assemble the product without error.

共5 页第2 页

Generally, a complete set of Working drawings for an assembly includes:

(1) Detail drawings of each nonstandard parts.

(2) An assembly or subassembly drawing showing all the standard and nonstandard parts in a

single drawing.

(3) A bill of materials (BOM).

(4) A title block.

A detail drawing is a dimensioned, multiview drawing of a single part, describing the part’s

shape, size, material, and surface roughness, in sufficient detail for the part to be manufactured based on the drawing alone. Detail drawings are produced from design sketches or extracted from 3-D computer models. They adhere strictly to ANSI standards and the standard for the specific company, for dimensioning, assigning part numbers, notes, tolerances, etc.

In an assembly, standard parts such as threaded fasteners and bearings are not drawn as details, but are shown in the assembly view. Standard parts are not drawn as details because they are normally purchased, not manufactured, for assembly.

For large assemblies or assembled with large parts, details are drawn on multiple sheets, and a separate sheet is used for the assembly view. If the assembly is simple or the parts are small, detail drawings for each part of an assembly can be placed on a single sheet.

Multiple details on a sheet are usually drawn at the same scale. If different scales are used, they are clearly marked under each detail. Also, when more than one detail is placed on a sheet, the spacing between details is carefully planned, including leaving sufficient room for dimensions and notes.

36. Based on the message, which of the follow is wrong?

A) standard parts needn’t drawn as details

B) for simple parts, sometimes needn’t to draw the detail working drawing

C) for large assemblies details may drawn on multiple sheets

D) If different scales used in a single sheet, they should clearly marked under each detail

37. Working drawings for an assembly MAY NOT includes: ?

A) BOM B) title block

C) An assembly or subassembly drawing D) Detail drawings of all parts.

38. For detail drawing, Which one of the following statement is not true ?

A) should not has different scales

B) Detail drawing can produced from design sketches or extracted from 3-D computer

models.

C) detail drawing is a dimensioned, multiview drawing of a single part

D) should Adhere strictly to ANSI standards

39. From the message we can infer ANSI is ?

A) a set of law B) a set of notification

C) an Organization D) IEEE government

40. The topic of the message is ?

A) How to design working drawings.

B) working drawing’s character and the key influence of how to draw a working drawing

C) In the design process, what should be considered?

D) What is working drawing

订

线

TEXT 3

One principle aim of kinematics is to create (design) the desired motions of the subjects’ mechanical parts and then mathematically compute the positions, velocities, and accelerations, which those will create on the parts. Since, for most earthbound mechanical systems, the mass remains essentially constant with time, defining the accelerations as a function of time then also defines the dynamic forces as a function of time. Stresses, in turn, will be a function of both applied and inertial (ma) forces. Since engineering design is charged with creating systems which will not fail during their expected service life, the goal is to keep stresses within acceptable limits for the materials chosen and the environmental conditions encountered. This obviously requires that all system forces be defined and kept within desired limits. In machinery, the largest forces encountered are often those due to the dynamics of the machine itself. These dynamic forces are proportional to acceleration, which brings us back to kinematics, the foundation of mechanical design. Very basic and early decision in the design process involving kinematic principles can be crucial to the success of any mechanical design; a design which has poor kinematics will prove troublesome and perform badly.

Any mechanical system can be classified according to the number of degree of freedom (DOF) which it processes. The system’s DOF is equal to the number of independent parameters which are needed to uniquely define its position in space at any instant of time.

A rigid body free to move within a reference frame will, in the general case, has complex motion, which is a simultaneous combination of rotation and translation. In three-dimensional space, there may be rotation about any axis and also simultaneous translation which can be resolved into components along three axes. In a plane, or two-dimensional space, complex motion becomes a combination of simultaneous rotation about one axis (perpendicular to the plane) and also translation resolved into components along two axes in the plane

41、Kinematics research focus on the following EXCEPT ______..

A) accelerations B) force

C) positions, D) velocities

42、From the passage that for the design engineer the first and most important is____

A) the service life of a machine B) the materials choose

C) the degree of freedom D) kinematic principles

43、An mechanical system has uniquely defined position in space at any instant of time that ___.

A) It should has one DOF

B) It should Has two DOF

C) the DOF and the number of independent parameters should equal

D) It should has any DOF as want

44、which one of the following is NOT TRUE _______?.

A) A rigid body free to move in three-dimensional space may rotation about any axis

B) A rigid body free to move in three-dimensional space is a simultaneous combination of rotation

and translation

C) A rigid body free to move in three-dimensional space can be resolved into components along

three axes

D) A rigid body free to move in three-dimensional space may has complex motion

45、The best title for this passage would be _______.

A) kinematics B) dynamics

C) kinematics and dynamic D) the important of kinematics

共5 页第3 页

四、英译汉（共20分）

1．将下列英语句子译成汉语（共5小题，每小题2分）

（1）A perfectly rigid or inextensible link can exist only as a textbook type of model of

a real machine member.

（2）Foundations should ensure the machine’s stiffness; shock absorption and isolation are secondary considerations.

(3)Thus, if a mechanical component such as a spring is subjected to repetitive or cyclical

applications of stress levels much lower than the ultimate strength, it will fracture after a large number of repetitions of this stress.

（4）Interchangeability means that identical parts must be interchangeable, i.e., able to replace each other, whether during assembly or subsequent maintenance work; without the need for any fitting operations.

（5）A gear can be gripped axially between a shoulder on the shaft and a spacer, with torque being transmitted through a key.

2、将下段英语翻译成汉语（10分）

As we look around us we see a world full of “things”, machines, devices, tools, things that we have designed, built, and used; things made of wood, metals, ceramics, and plastics. We know from experience that some things are better than others; they last longer, cost less, are quieter, or are ease to use. Ideally , however, every such item has been designed according to some set of “functional requirements” as perceived by the designers—that is, it hs been designed so as to answer the question, “exactly what function should it perform?” In the world of engineering, the major function frequently is to support some type of loading due to weight, inertia , pressure, etc.

五、英译汉（共20分）

1、将下列句子译成英语（共5小题，每小题2分）

（1）一个或多个诸如齿轮，链轮，皮带轮和凸轮等类的构件通常借助于销、键、花键、卡环或其它装置连接到轴上。

（2）运动学仅研究机构的运动，而不考虑作用在机构上的力。

（3）工程上的许多问题在其本质上是非线性的，也就是说恢复力并不与位移成正比，而且阻尼力也不与速度的一次方成正比。

（4）在物体上所画的一条基准线，只会改变他的位置，而不会改变他的角度方向。

订

线

（5）当一个装置意外地失效后，通常需要进行研究工作，来找出失效的原因和确定可能的改正措施。

2. 将下段汉语翻译成英语（10分）

密度：材料的密度是指单位体积材料的质量。另外一个术语是比重，其表示某种材料的密度与水的密度的比值，因此，比重没有单位。对于如飞机和航天结构、汽车车体和部件，以及其他一些产品，当能量消耗和动力限制是主要考虑的因素时，减轻重量尤其重要。在设计先进的设备与机器和设计诸如汽车等消费品的过程中，采用新的替代材料来减轻重量和降低成本是一个应该着重考虑的问题

共 5 页第4 页

专业英语参考答案及评分标准（重修）

一、选择题: （本大题共15小题，每小题1分，总计15分）

1-5：BCDCB 6-10：ACBCA 11-15 DACAB

二、完形填空：（本大题共15小题，每小题1分，总计15分）

16-20：BDABC 21-25 ：BABDB 26-30：CBCAD

三、阅读理解：（本大题共20小题，每小题2分，总计40分）

31-35：ADABC 36-40 ：BC ACD 41-45：BDCA C

四、翻译（满分40分）

1、英译汉，(共5小题，每小题2分)

（1）A perfectly rigid or inextensible link can exist only as a textbook type of model of a real machine member.

一个绝对刚性或者不可伸长的构件只能作为真实机器零件在教科书中的模型而存在。

（2）Foundations should ensure the machine’s stiffness; shock absorption and isolation are secondary considerations.

基础应该保证机器的刚度，减震和隔离是次要的考虑事项。

(3)Thus, if a mechanical component such as a spring is subjected to repetitive or cyclical applications of stress levels much lower than the ultimate strength, it will fracture after a large number of repetitions of this stress.

因此，像弹簧这样的机械零件，在比其极限强度低很多的重复应力或周期性应力下，经过很多次的重复作用之后也会发生断裂.

（4）Interchangeability means that identical parts must be interchangeable, i.e., able to replace each other, whether during assembly or subsequent maintenance work; without the need for any fitting operations.

互换性意味着在相同的零件之间必须能够进行互换。无论是在装配时还是在其后的维修时，这些零件都可以互相取代而不需任何修配工作。

（5）A gear can be gripped axially between a shoulder on the shaft and a spacer, with torque being transmitted through a key.

一个齿轮可以用轴肩和挡圈进行轴向固定，并通过键来传递。

2、英译汉，10分

As we look around us we see a world full of “things”, machines, devices, tools, things that we have designed, built, and used; things made of wood, metals, ceramics, and plastics. We know from experience that some things are better than others; they last longer, cost less, are quieter, or are ease to use. Ideally , however, every such item has been designed according to some set of “functional requirements” as perceived by the designers—that is, it hs been designed so as to answer the question, “exactly what function should it perform?” In the world of engineering, the major function frequently is to support some type of loading due to weight, inertia , pressure, etc.

当我们环顾四周，我们可以看到一个充满“物体”的世界，机器、设备、工具等一切由我们设计、建造和使用的物体；有木头、金属、水泥和塑料制成的物体。从我们的经验我们知道一些物体会比其他一些物体更好，如使用寿命更长，成本更低，更轻便或者更容易使用。然而，在理想的情况下，每一件产品都是设计人员根据其对某些“功能要求”的理解而设计出来的，也就是说，在设计过程中，应该回答这样的问题，即“它应该具有那种确切的功能？” 在工程界中，最经常的功能是支撑一些由于重量、惯性力及压力等引起的载荷。

3、汉译英(共5小题，每小题2分)

（1）一个或多个诸如齿轮，链轮，皮带轮和凸轮等类的构件通常借助于销、键、花键、卡环或其它装置连接到轴上。

One or more members such as gears, sprockets, pulleys, and cams are usually attached to the shaft by means of pins, keys, splines, snap rings, and other devices.

（2）运动学仅研究机构的运动，而不考虑作用在机构上的力。

Kinematics is the study of motion in mechanisms without reference to the forces that act on the mechanism.

（3）工程上的许多问题在其本质上是非线性的，也就是说恢复力并不与位移成正比，而且阻尼力也不与速度的一次方成正比。

Many vibration problems in engineering are nonlinear in nature, i.e. the restoring forces are not proportional to the displacements and the damping forces are not proportional to the first power of the velocity.

（4）A reference line drawn on the body changes its linear position but does not change its angular orientation.

在物体上所画的一条基准线，只会改变他的位置，而不会改变他的角度方向。

（5）当一个装置意外地失效后，通常需要进行研究工作，来找出失效的原因和确定可能的改正措施。

When a device fails (unexpectedly) it is often necessary to carry out a study to pinpoint the cause of failure and to identify potential corrective measures

4、汉译英，10分

密度：材料的密度是指单位体积材料的质量。另外一个术语是比重，其表示某种材料的密度与水的密度的比值，因此，比重没有单位。对于如飞机和航天结构、汽车车体和部件，以及其他一些产品，当能量消耗和动力限制是主要考虑的因素时，减轻重量尤其重要。在设计先进的设备与机器和设计诸如汽车等消费品的过程中，采用新的替代材料来减轻重量和降低成本是一个应该着重考虑的问题

Density: the density of a material is its mass per unit volume. Another term id specific gravity, which express a material’s density in relation to that of water, and thus, it has no units.Weight saving is important particularly for aircraft and aerospace structures, for automotive bodies and components, and for other products where energy consumption and power limitations are major concerns. Substitution of materials for the sake of weight saving and economy is a major factor in the design both of advanced equipment and machinery and of consumer products, such as automobiles.

机械专业英语词汇合集-机械人必背(字母表版)

西南交通大学2013级研究生录 V ocabulary A accessory附件，辅助设备 accordingly因此，从而 accuracy精确性 acetylene乙炔 acrylics丙烯酸树脂 acrylonitrile丙烯腈 adjusted调整过的 advent出现，到来 aligned对齐的，均衡的 aligned排列的 alloy合金 alphanumeric文字数字的，包含文字与数字的aluminum铝 ambiguously含糊不清地 amenable易控制的 amorphous无定形的，非晶态的 analogous类似的 angle角度 annealing退火 anvil铁砧 appendant下垂物 approach接近，方法，接近，靠近 arbor藤架，凉亭 argon氩气 artificial人造的 assist辅助 asymmetric不对称的 atop在顶上 attaching附属的 automatically自动的，机械的 automation自动化 automobile汽车，车辆 auxiliairy辅助的，补助的 axis轴 B bartender酒吧间男招待 batch一批，一组 beam光线 bearing轴承 binder粘合物 biomaterial生物材料

blacksmith铁匠，锻工 blade刀锋，刀口 blanking空白，下料，落料 blast爆破，冲击波 blowtorch吹管 blunt钝的 bolt螺栓 bond键，使粘合，使结合 boost推进 borer钻孔器 boring钻孔 bottleneck瓶颈 brazing硬钎焊 brittleness脆性 bronze青铜 burlap粗麻布 C calibrate校准 cam凸轮 capital首都，资本，资金，首都的，重要的cappuccino卡布奇诺，热牛奶咖啡 carbide碳化物 carburetor化油器 carburize使渗碳 carcass畜体 carriage溜板，拖板 carve雕刻 casino赌博娱乐场 cast铸造 casting铸造 catalysis催化作用 cathode阴极 cavity型腔，模腔，凸模 ceramogrophy陶瓷学 challenging复杂的 choke阻风的，气门的 chore家务杂事 chromium铬 chuck卡盘 clamp夹具，锁紧，夹紧，固定 clay泥土 clumsy笨重的，笨拙的，不灵活的 clutch离合器 coalescence合并，结合，联合

(完整版)机械工程专业英语词汇

陶瓷ceramics 合成纤维synthetic fibre 电化学腐蚀electrochemical corrosion 车架automotive chassis 悬架suspension 转向器redirector 变速器speed changer 板料冲压sheet metal parts 孔加工spot facing machining 车间workshop 工程技术人员engineer 气动夹紧pneuma lock 数学模型mathematical model 画法几何descriptive geometry 机械制图Mechanical drawing 投影projection 视图view 剖视图profile chart 标准件standard component 零件图part drawing 装配图assembly drawing 尺寸标注size marking 技术要求technical requirements 刚度rigidity 内力internal force 位移displacement 截面section 疲劳极限fatigue limit 断裂fracture 塑性变形plastic distortion 脆性材料brittleness material 刚度准则rigidity criterion 垫圈washer 垫片spacer 直齿圆柱齿轮straight toothed spur gear 斜齿圆柱齿轮helical-spur gear 直齿锥齿轮straight bevel gear 运动简图kinematic sketch 齿轮齿条pinion and rack 蜗杆蜗轮worm and worm gear 虚约束passive constraint 曲柄crank 摇杆racker 凸轮cams

《机械工程专业英语教程》课文翻译

Lesson 1 力学的基本概念 1、词汇： statics [st?tiks] 静力学；dynamics动力学；constraint约束；magnetic [m?ɡ＇netik]有磁性的；external [eks＇t?:nl] 外面的, 外部的；meshing啮合；follower从动件；magnitude [＇m?ɡnitju:d] 大小；intensity强度，应力；non-coincident [k?u＇insid?nt]不重合；parallel [＇p?r?lel]平行；intuitive 直观的；substance物质；proportional [pr?＇p?:??n?l]比例的；resist抵抗，对抗；celestial [si＇lestj?l]天空的；product乘积；particle质点；elastic [i＇l?stik]弹性；deformed变形的；strain拉力；uniform全都相同的；velocity[vi＇l?siti]速度；scalar[＇skeil?]标量；vector[＇vekt?]矢量；displacement代替；momentum [m?u＇ment?m]动量； 2、词组 make up of由……组成；if not要不，不然；even through即使，纵然； Lesson 2 力和力的作用效果 1、词汇： machine 机器；mechanism机构；movable活动的；given 规定的，给定的，已知的；perform执行；application 施用；produce引起，导致；stress压力；applied施加的；individual单独的；muscular [＇m?skjul?]]力臂；gravity[ɡr?vti]重力；stretch伸展，拉紧，延伸；tensile[tensail]拉力；tension张力，拉力；squeeze挤；compressive 有压力的，压缩的；torsional扭转的；torque转矩；twist扭，转动；molecule [m likju:l]分子的；slide滑动; 滑行；slip滑，溜；one another 互相；shear剪切；independently独立地，自立地；beam梁；compress压；revolve (使)旋转；exert [iɡ＇z?:t]用力，尽力，运用，发挥，施加；principle原则, 原理，准则，规范；spin使…旋转；screw螺丝钉；thread螺纹； 2、词组 a number of 许多；deal with 涉及，处理；result from由什么引起；prevent from阻止，防止；tends to 朝某个方向；in combination结合；fly apart飞散； 3、译文： 任何机器或机构的研究表明每一种机构都是由许多可动的零件组成。这些零件从规定的运动转变到期望的运动。另一方面，这些机器完成工作。当由施力引起的运动时，机器就开始工作了。所以，力和机器的研究涉及在一个物体上的力和力的作用效果。 力是推力或者拉力。力的作用效果要么是改变物体的形状或者运动，要么阻止其他的力发生改变。每一种

机械专业英语词汇汇总

机械专业英语词汇（大全） 金属切削metal cutting 机床machine tool 金属工艺学technology of metals 刀具cutter 摩擦friction 联结link 传动drive/transmission 轴shaft 弹性elasticity 频率特性frequency characteristic 误差error 响应response 定位allocation 机床夹具jig 动力学dynamic 运动学kinematic 静力学static 分析力学analyse mechanics 拉伸pulling 压缩hitting 剪切shear 扭转twist 弯曲应力bending stress 强度intensity 三相交流电three-phase AC 磁路magnetic circles 变压器transformer 异步电动机asynchronous motor 几何形状geometrical 精度precision 正弦形的sinusoid 交流电路AC circuit 机械加工余量machining allowance 变形力deforming force 变形deformation 应力stress 硬度rigidity 热处理heat treatment 退火anneal 正火normalizing 脱碳decarburization 渗碳carburization 电路circuit 半导体元件semiconductor element 反馈feedback 发生器generator 直流电源DC electrical source 门电路gate circuit 逻辑代数logic algebra 外圆磨削external grinding 内圆磨削internal grinding 平面磨削plane grinding 变速箱gearbox 离合器clutch 绞孔fraising 绞刀reamer 螺纹加工thread processing 螺钉screw 铣削mill 铣刀milling cutter 功率power 工件workpiece 齿轮加工gear mechining 齿轮gear 主运动main movement 主运动方向direction of main movement 进给方向direction of feed 进给运动feed movement 合成进给运动resultant movement of feed 合成切削运动resultant movement of cutting 合成切削运动方向direction of resultant movement of cutting 切削深度cutting depth 前刀面rake face 刀尖nose of tool 前角rake angle 后角clearance angle 龙门刨削planing 主轴spindle 主轴箱headstock 卡盘chuck 加工中心machining center

机械专业英语复试词汇总结

机械英语词汇大全2 金属切削 metal cutting 机床 machine tool 金属工艺学 technology of metals 刀具 cutter 摩擦 friction 联结 link 传动 drive/transmission 轴 shaft 弹性 elasticity 频率特性 frequency characteristic 误差 error 响应 response 定位 allocation 拉孔 broaching 装配 assembling 铸造 found 流体动力学 fluid dynamics 流体力学 fluid mechanics 加工 machining 液压 hydraulic pressure 切线 tangent 机电一体化 mechanotronics mechanical-electrical integration 气压 air pressure pneumatic pressure 稳定性 stability 介质 medium 数学模型 mathematical model 画法几何 descriptive geometry 机械制图 Mechanical drawing 投影 projection 视图 view 剖视图 profile chart 标准件 standard component 零件图 part drawing 装配图 assembly drawing 尺寸标注 size marking 技术要求 technical

机床夹具 jig 动力学 dynamic 运动学 kinematic 静力学 static 分析力学 analyse mechanics 拉伸 pulling 压缩 hitting 剪切 shear 扭转 twist 弯曲应力 bending stress 强度 intensity 三相交流电 three-phase AC 磁路 magnetic circles 变压器 transformer 异步电动机 asynchronous motor 液压驱动泵 fluid clutch 液压泵 hydraulic pump 阀门 valve 失效 invalidation 强度 intensity 载荷 load 应力 stress 安全系数 safty factor 可靠性 reliability 螺纹 thread 螺旋 helix 键 spline 销 pin 滚动轴承 rolling bearing 滑动轴承 sliding bearing requirements 刚度 rigidity 内力 internal force 位移 displacement 截面 section 疲劳极限 fatigue limit 断裂 fracture 塑性变形 plastic distortion 脆性材料 brittleness material 刚度准则 rigidity criterion 垫圈 washer 垫片 spacer 直齿圆柱齿轮

机械工程专业英语 翻译

2、应力和应变 在任何工程结构中独立的部件或构件将承受来自于部件的使用状况或工作的外部环境的外力作用。如果组件就处于平衡状态,由此而来的各种外力将会为零,但尽管如此,它们共同作用部件的载荷易于使部件变形同时在材料里面产生相应的内力。 有很多不同负载可以应用于构件的方式。负荷根据相应时间的不同可分为: (a)静态负荷是一种在相对较短的时间内逐步达到平衡的应用载荷。 (b)持续负载是一种在很长一段时间为一个常数的载荷, 例如结构的重量。这种类型的载荷以相同的方式作为一个静态负荷; 然而,对一些材料与温度和压力的条件下,短时间的载荷和长时间的载荷抵抗失效的能力可能是不同的。 (c)冲击载荷是一种快速载荷(一种能量载荷)。振动通常导致一个冲击载荷, 一般平衡是不能建立的直到通过自然的阻尼力的作用使振动停止的时候。 (d)重复载荷是一种被应用和去除千万次的载荷。 (e)疲劳载荷或交变载荷是一种大小和设计随时间不断变化的载荷。 上面已经提到，作用于物体的外力与在材料里面产生的相应内力平衡。因此,如果一个杆受到一个均匀的拉伸和压缩，也就是说, 一个力,均匀分布于一截面,那么产生的内力也均匀分布并且可以说杆是受到一个均匀的正常应力,应力被定义为 应力==负载 P /压力 A, 因此根据载荷的性质应力是可以压缩或拉伸的,并被度量为牛顿每平方米或它的倍数。 如果一个杆受到轴向载荷，即是应力，那么杆的长度会改变。如果杆的初始长度L和改变量△L已知，产生的应力定义如下: 应力==改变长△L /初始长 L 因此应力是一个测量材料变形和无量纲的物理量 ,即它没有单位;它只是两个相同单位的物理量的比值。 一般来说,在实践中,在荷载作用下材料的延伸是非常小的, 测量的应力以*10-6的形式是方便的, 即微应变, 使用的符号也相应成为ue。 从某种意义上说，拉伸应力与应变被认为是正的。压缩应力与应变被认为是负的。因此负应力使长度减小。 当负载移除时，如果材料回复到初始的，无负载时的尺寸时，我们就说它是具有弹性的。一特定形式的适用于大范围的工程材料至少工程材料受载荷的大部分的弹性, 产生正比于负载的变形。由于载荷正比于载荷所产生的压力并且变形正比于应变, 这也说明,当材料是弹性的时候, 应力与应变成正比。因此胡克定律陈述, 应力正比于应变。 这定律服从于大部分铁合金在特定的范围内, 甚至以其合理的准确性可以假定适用于其他工程材料比如混凝土，木材，非铁合金。 当一个材料是弹性的时候，当载荷消除之后，任何负载所产生的变形可以完全恢复,没有永久的变形。

选矿书籍大全

选矿书籍大全 1. 大学教材 1.1 冶金工业出版社高校统编教材 《矿石学基础（第2版）》 《工艺矿物学》 《选矿概论》 《碎矿和磨矿》 《重力选矿（修订版）》（孙玉波主编，1993） 《磁电选矿》（王常任主编，1986出版；有书签） 《浮选[已经补齐]》（胡为柏版） 《矿物化学处理》 《选厂设计合集》 《化学选矿》 《化学选矿（原理、工艺及实践）》 《选矿电磁学》（昆工版，pdf，有书签） 《碎矿与磨矿(第二版)》 《碎矿与磨矿》 1.2 近年来新式教材（淡化专业性教材） 《矿物加工颗粒学》（选矿专业研究生教材之一） 《矿物颗粒分选工程》 《选矿学》(其实是选煤学，没有电选、化选内容，磁选和浮选一般) 《资源加工学》 《固体物料分选理论与工艺》 《选矿厂设计》（周龙廷高清第2版+书签+水印） 1.3 冶金行业职业教育培训规划教材 《碎矿与磨矿技术》 《磁电选矿技术》 《浮游选矿技术》 《重力选矿技术》 《化学选矿》黄尔君（高清） 1.4 其他经典教材 《浮游选煤与选矿》(蔡璋) 《浮选》（郭梦熊） 《矿石可选性研究(邱,超星)》 《矿石可选性研究（pdf）》（中南版） 《矿石可选性研究方法（pdf）》（邱版） 《老版的：矿石可选性研究》 《矿物浮选原理(书签+水印）》（卢版） 《重选原理》（老版教材） 《选矿厂设计（铁矿）》 《选矿厂设计(有色矿) 》（中南版） 《金与有色金属矿选矿厂设计》（徐正春版)

《大学生毕业设计指导教程（冶金，选矿，化工分册）》 《国外选矿设计名著 《选矿工艺》(侧重洗煤) 《选矿工艺与设备的概论.doc》 《[To] win_zw , 关于选矿工艺学方面教程》 《选矿工艺学(书签+水印）》 《很实用的浮选教材》 【基础化学丛书】《无机化学》《有机化学》《物理化学》《分析化学》1.5 专业英语 《选矿工程专业英语》 《选矿英语教材》 《简明英汉矿业词典》(在学校没有认真学专业英语的人有福了！）《汉英－英汉图解矿物加工词典》 《汉英-英汉矿物加工图解词典\邹志毅》 《矿物加工科技英语》 2 专著类书籍 2.1 选矿总论部分（不分矿种） 【数学模型】 《选矿数学模拟与模型》 《数学模型在矿物工程中的应用》（胡为柏李松仁著，1983） 【磁电选矿】 《磁种分选理论与实践》 《磁选理论及工艺（书签+水印）》 《高梯度磁力分离》 《铁矿石电选新工艺新技术-摩擦电选工艺理论（word版）》 《超导磁选及其进展》 《矿物电选》 【化学选矿】 《化学冶金（英文版）》 《有关选冶联合方面的名著-化工冶金(化学选矿)原理与实践》 《堆浸的原理和工艺》 《浸矿技术》 《加压浸出吸附萃取》 《矿浆电解原理》 《资源微生物技术》 《生物技术在矿物加工中的应用》-2008新书 《化学分离富集方法及应用》 【重力选矿】 《矿物分离过程动力学》 《微细与超细难选矿泥射流流膜离心分选法》 《悬浮液选矿理论与工艺新发展》 《水力旋流器分离技术》作者：赵庆国 《水筛理论及应用》文书明著 【浮游选矿】

机械制造专业英语文章

机械制造专业英语文章 篇一：机械专业英语文章中英文对照 Types of Materials 材料的类型 Materials may be grouped in several ways. Scientists often classify materials by their state: solid, liquid, or gas. They also separate them into organic (once living) and inorganic (never living) materials. 材料可以按多种方法分类。科学家常根据状态将材料分为：固体、液体或气体。他们也把材料分为有机材料(曾经有生命的)和无机材料(从未有生命的)。 For industrial purposes, materials are divided into engineering materials or nonengineering materials. Engineering materials are those used in manufacture and become parts of products. 就工业效用而言，材料被分为工程材料和非工程材料。那些用于加工制造并成为产品组成部分的就是工程材料。 Nonengineering materials are the chemicals, fuels, lubricants, and other materials used in the manufacturing process, which do not become part of the product. 非工程材料则是化学品、燃料、润滑剂以及其它用于加工制造过程但不成为产品组成部分的材料。 Engineering materials may be further subdivided into: ①Metal ②Ceramics ③Composite ④Polymers, etc. 工程材料还能进一步细分为：①金属材料②陶瓷材料③复合材料④聚合材料，等等。 Metals and Metal Alloys 金属和金属合金 Metals are elements that generally have good electrical and thermal conductivity. Many metals have high strength, high stiffness, and have good ductility. 金属就是通常具有良好导电性和导热性的元素。许多金属具有高强度、高硬度以及良好的延展性。 Some metals, such as iron, cobalt and nickel, are magnetic. At low temperatures, some metals and intermetallic compounds become superconductors. 某些金属能被磁化，例如铁、钴和镍。在极低的温度下，某些金属和金属化合物能转变成超导体。 What is the difference between an alloy and a pure metal? Pure metals are elements which come from a particular area of the periodic table. Examples of pure metals include copper in electrical wires and aluminum in cooking foil and beverage cans. 合金与纯金属的区别是什么？纯金属是在元素周期表中占据特定位置的元素。 例如电线中的铜和制造烹饪箔及饮料罐的铝。 Alloys contain more than one metallic element. Their properties can be changed by changing the elements present in the alloy. Examples of metal alloys include stainless steel which is an alloy of iron, nickel, and chromium; and gold jewelry which usually contains an alloy of gold

机械工程专业英语施平没翻译课文补充.docx

. 4、工程机械概述 As we look around us we see a world full of“things”: machines, devices, tools; things that we have designed, built,and used; things made of wood, metals,ceramics, and plastics.We know from experience that some things are better than others;they last longer, cost less, are quieter, look better, or are easier to use. ; ; 情况 . Ideally, however, every such item has been designed according to some set of “functional requirements”as perceived by the designers—that is, it has been designed so as to answer the question,“Exactly what function should it perform?” In the world of engineering, the major function frequently is to support some type of loading due to weight, inertia, pressure, etc. 的 From the beams in our homes to the wings of an airplane, there must be an appropriate melding of materials,dimensions, and fastenings to produce structures that will perform their functions reliably for a reasonable cost over a reasonable

机械工程专业英语(李光布_华中科技大学出版社)课后答案

《机械工程专业英语》翻译李光布饶锡新主编华中科技大学出版社Lesson11 numerical control Introduction One of the most fundamental concepts in the area …………………… 数控就是用一个穿孔的纸带或存储的程序来控制机床，美国电子工业协会对数字控制所下的定义为：“一个各项工作都有在各点上直接插入的数字来控制的系统，该系统必须至少能够自动解释这些数字中的部分。”生产某个零件所需要的数据被称作这个零件程序数控比先前的手工操作生产更多的机械设备，数控机床能够自动的生产不同种类的零件，并且这些零件都有各种各样复杂的加工工艺过程，数字控制使得制造者们可以承担产品的加工，其产品的加工从经济的观点上看使用人工控制机床和加工过程是不太可行的的当一个孔被钻或冲出后，刀具向上撤回快速移动到下一个位置，重复这个步骤，路线沿着一个位置到另一个位置在某一方面是很重要的，他必须挑选一个是经过的时间减少、更有效（的路线）。点对点的系统主要用于钻床、冲床和连续的铣工序中 最近对DNC（现在表示分布式数字控制）的定义涵盖了“使用主计算机作为控制系统，来管理大量的带有机载微型计算机的独立的计算机数控机床”的含义。这种系统提供了更大的存储和计算机能力来灵活的克服直接数控的缺陷。 计算机数字控制是由控制微型计算机作为机器集成的部分或某种设备一部分的系统（如机载计算机）。零件程序由编程者事先准备好，该程序应结合由绘图软件包和加工仿真中获得的信息，从而确保零件没有程序缺陷。机器操控者可以很容易的通过手工对机载计算机进行控制，操作者能够直接对程序进行修改，并为不同的零件制定和存储程序 Lesson14 CAM TEXT 1.introduction Computer-aided manufacturing involves the use of …………………… 计算机辅佐制造的含义是：使用计算机和计算机技术来协助产品制造的所有环节，其中包括加工工艺和生产的辅助设计、加工、生产计划制定、管理和质量控制等！ 由CAD开发的数据库首先被存储，然后由CAM做进一步的处理，转化为对生产设备和材料处理设备进行操作和控制所必须的数据和命令，对产品的质量进行自动的检测和测试！ CAD\CAM的出现对制造业有很大的影响，标准化生产的发展和设计努力、试验和原型工作的减少。它已经较大的减少了消耗和提高生产效率成为可能。例如，波音777客机完全被用计算机（无纸的设计），在两千个工作站连接着8台计算机，这个飞机由CAD\CAM软件建造，没有原形或像以前的模型所要求的建立，这个开发的花费大约在60亿。 通过工业社会的历史，许多发明取得专利，并且整个新技术在发展，华特的零件互换性概念、瓦特的蒸汽机和福特的装配线是一部分发展却是最显著的在我们的工业时期，像我们知道的那样，这些发展的每一个都影响了制造业，并且赢得了他们个人应受认可在我们的历史课本中。或许数字计算机技术是唯一比以前技术更快、更大影响制造业的发展。 在计算机辅助设计或计算机辅助制造中交互式计算机制图起着重要的作用，通过使用交互式计算机制图，设计人员可开发被设计产品的图形图像，同时储存这些生成图形图像的电子数据，图像可以以二维三维的实体的形式表现出来，交互式计算机制图图像是由点、线、圆和曲线这些基本的几何元素构成的这些图像一旦创建他们可以通过放大缩小旋转和移动在内的各种各样的方式轻松的来编辑和操 交互式计算机制图系统的典型硬件结构包括计算机、显示器、软盘启动器、、硬盘或两者兼备以及输入设备、如键盘、绘图仪和打印机。这些设备伴随这些软件是现代设计人员用

研究生机械工程专业英语考试必背单词

研究生机械工程专业英语考试必背单词 Modified by JACK on the afternoon of December 26, 2020

单词 Lesson 1 Gear 齿轮, 传动装置 Bearing 轴承 Cams 凸轮 Cams and followers 凸轮和从动件 Couple 力偶 mechanics 力学 statics 静力学，静止状态 dynamics动力学，原动力，动力特性constraint forces 约束力 applied forces 作用力 Electric , magnetic, and gravitational forces 电,磁,重力 mating surface 啮合表面,配合表面,接触面meshing 啮合，咬合，钩住 meshing teeth 啮合齿 journal bearing 滑动轴承，向心滑动轴承metal-to-metal contact 金属 - 金属接触Overheating 过热 failure 失效 flaking 薄片，表面剥落，压碎 Spall 削，割，剥落，脱皮 noise 噪音 rough motion运动不精确 inertia惯性 particle 质点 rigid body刚体 deformable可变形的，应变的 deformable Body 变形体 Scalar 数量的，标量的 Vectors矢量 Density密度 Mass质量 Displacement位移 Velocity速度 Acceleration加速度 Moment力矩，弯矩 Momentum动量，冲量 Lesson 2 Compressive压缩的，有压力的 Turning 车削 Rectilinear直线的 micrometer 千分尺又称螺旋测微器 Power hacksaws 弓锯床 Shaper牛头刨床 Thread 螺纹 Work：功 muscular action肌肉动作 mechanical motion机械运动 stretch an object拉伸对象 tensile force：拉力 in tension：受拉 compressive force：压力 torsional force：扭力 torque：扭矩 shearing force ：剪切力 twist an object扭曲对象 Slide滑，脱落 Slip滑动，滑移 in compression受压 turning of a part对一个零件进行车削加工wedging action:楔入作用 chip ：切屑 centers of the lathe车床的顶尖 lathe dog车床夹头 centrifugal force ：离心力 grinding wheel ：磨削砂轮 bonding agent ：粘合剂 abrasive particle：磨料颗粒 centrifuge-type machines离心式机械Centrifuge离心机，离心作用 Centrifugal force principles离心力原理centripetal force ：向心力 rotary motion:回转运动 rectilinear motion：直线运动 hand tool手工工具 power tool动力工具 feed：进给 shaping：采用牛头刨床（shaper)进行刨削加工power saw：弓锯床，弓式锯床 the screw of a micrometer 意为“千分尺中的螺杆”harmonic and intermittent motion ：谐和运动和间歇运动 simple harmonic motion ：简谐运动

机械专业英语翻译软件

机械专业英语翻译软件 机械专业英语 （Science Readers of Machinery） 教学大纲 （学时范围：48学时） 一、课程性质和任务 本课程是机械设计制造及其自动化专业的一门选修课。通过本课程的学习,使学生达到基本能够阅读本专业一般英语资料的目的。 二、课程内容及要求 本课程通过课堂教学,使学生基本掌握本专业领域的一些常用词汇、词组和句型结构,基本能够阅读本专业领域一般难度的英语文章,并借助词典能够阅读本专业领域中等难度的英语文章。 本课程的基本内容包括: （1）材料与成型加工 （2）机器部件与设计 （3）机床与机加工 （4）制造与自动化 （5）现代制造工程与发展 以上内容均由三部分组成,包括:单词与词组、重点句的翻译及分析、课后阅读。 本课程的基本要求包括 了解：课后阅读材料的内容,能理解阅读材料大意。 熟悉：课文原意,能将课文翻译成中文。 掌握：课文中所出现的词汇与重点句型。 三、本课程与其它相关课程的联系与分工 先修课程：机械设计、机械制造基础、数控技术、现代制造工程等。 后续课程：毕业设计。 四、实践性教学内容的安排与要求 本课程的实践环节主要通过课后多次阅读所学课文，并对重点句进行中文翻译。 五、本课程在课外作业练习方面的要求 本课程的课外作业主要为课后阅读，并将重点句英语翻译成汉语。 六、本课程在使用现代化教学手段方面的要求 无特殊要求。 七、教材及参考书 教材：黄运尧编，机械专业英语阅读教程，机械工业出版社，1998年八、本课程成绩的考核方法及评定标准 本课程的考核以笔试为主，主要考查将本专业领域的英文文章翻译为汉语，成绩

以二分制计算（通过/不通过）。 九、学时分配（总40学时）

2013机械专业人才培养方案.

2013级机械设计制造及其自动化专业人才培养方案 一、培养目标 本专业培养社会主义建设需要的，德、智、体全面发展的，具有从事机电一体化产品和系统的运行、维护、设计、制造及开发基本能力的高级应用型专门人才。学生通过必须的理论课程及实践教学环节的学习，获得工程师的基本训练，毕业生达到本科基本要求。在政治思想道德方面：热爱祖国，拥护党的基本路线，具有全心全意为人民服务的精神。遵纪守法，有良好的社会公德和职业道德。 二、培养规格 本专业采用：“通识教育，厚基础，宽口径，分类培养”的教学管理模式，具有机电一体化的特色。学生主要学习机械设计与制造的基础理论，学习微电子技术的基本知识，受到现代机械工程师的基本训练，具有进行机械产品设计、制造及设备控制、生产组织管理的基本能力。 毕业生应获得以下几方面的知识和能力： 1、具有正确的政治方向，热爱祖国，拥护中国共产党的领导，掌握马列主义、毛泽东思想和 邓小平理论的基本知识；树立科学的世界观、人生观和价值观，具有崇高的爱国主义精神和共产主义的道德品质； 2、具有较扎实的自然科学和人文社会科学基础，具有良好的身体素质和心理素质； 3、具有一定的英语听说读写能力，能阅读本专业英文书刊； 4、具有计算机应用基本能力，受到计算机辅助设计制造的基本训练，掌握资料查询、文献检 索及运用现代信息技术获取相关信息的基本方法； 5、较系统地掌握本专业领域宽广的技术理论基础知识，具有本专业必需的制图、计算、实验、 测试、文献检索和基本工艺操作等基本技能； 6、具有较强的自学能力和创新意识，具有初步的科学研究、科技开发及组织管理能力和团队 协作精神，了解其学科前沿及其发展趋势。 三、专业方向 1. 机械设计与制造方向 2.机械电子方向

机械专业英语翻译

专业英语翻译论文 学校：昆明理工大学 学院：机电工程学院 专业：机械工程 学生姓名：胡勇 任课教师：蒋红 日期： 2015 年 5 月 学号： 2014703022 Friction , Lubrication of Bearing

In many of the problem thus far , the student has been asked to disregard or neglect friction . Actually , friction is present to some degree whenever two parts are in contact and move on each other. The term friction refers to the resistance of two or more parts to movement. Friction is harmful or valuable depending upon where it occurs. friction is necessary for fastening devices such as screws and rivets which depend upon friction to hold the fastener and the parts together. Belt drivers, brakes, and tires are additional applications where friction is necessary. The friction of moving parts in a machine is harmful because it reduces the mechanical advantage of the device. The heat produced by friction is lost energy because no work takes place. Also , greater power is required to overcome the increased friction. Heat is destructive in that it causes expansion. Expansion may cause a bearing or sliding surface to fit tighter. If a great enough pressure builds up because made from low temperature materials may melt. There are three types of friction which must be overcome in moving parts: (1)starting, (2)sliding, and(3)rolling. Starting

机械专业英语试题及答案精编WORD版

机械专业英语试题及答案精编W O R D版 IBM system office room 【A0816H-A0912AAAHH-GX8Q8-GNTHHJ8】

学院院长（系 主任） （签字）

C. degradation…corrosion D. corrosion… degradation 12. Most frames _______ cast iron, weld steel, composition, or concrete. A. are made from B. are made up of C. was produced by D. was consist of 13. Rotating shafts particularly those that run at high speeds, must be designed to avoid operation at speeds. A . low B .overload C. critical D. hollow 14. Although cast iron is a fairly cheap material, each casting requires a . A. pattern B. model C. mold D. patent 15. The term is used to describe joints with surface contact, as with a pin surrounded by a hole. A. high pair B. low pair C. surface pair D. rotary pair 二、完型填空（在每个小题四个备选答案中选出一个正确答案，本大题共15小题，每小题1分，总计15分） The term shaft usually refers to a relatively long member of round cross section that rotates and transmits power. One or more members such as gears, sprockets, pulleys, and cams are usually (16) to the shaft by means of pins, keys, splines, snap rings, and other devices. These latter members are among the “associated parts” considered in this text, as are couplings and universal joint, which serve to (17) the shaft to the source of power or load.