单片机外文翻译
AT89C51的概况
1 AT89C51应用
单片机广泛应用于商业：诸如调制解调器，电动机控制系统，空调控制系统，汽车发动机和其他一些领域。这些单片机的高速处理速度和增强型外围设备集合使得它们适合于这种高速事件应用场合。然而，这些关键应用领域也要求这些单片机高度可靠。健壮的测试环境和用于验证这些无论在元部件层次还是系统级别的单片机的合适的工具环境保证了高可靠性和低市场风险。Intel 平台工程部门开发了一种面向对象的用于验证它的AT89C51 汽车单片机多线性测试环境。这种环境的目标不仅是为AT89C51 汽车单片机提供一种健壮测试环境，而且开发一种能够容易扩展并重复用来验证其他几种将来的单片机。开发的这种环境连接了AT89C51。本文讨论了这种测试环境的设计和原理，它的和各种硬件、软件环境部件的交互性，以及如何使用AT89C51。
1.1 介绍
8 位AT89C51 CHMOS 工艺单片机被设计用于处理高速计算和快速输入/输出。MCS51 单片机典型的应用是高速事件控制系统。商业应用包括调制解调器，电动机控制系统，打印机，影印机，空调控制系统，磁盘驱动器和医疗设备。汽车工业把MCS51 单片机用于发动机控制系统，悬挂系统和反锁制动系统。AT89C51 尤其很好适用于得益于它的处理速度和增强型片上外围功能集，诸如：汽车动力控制，车辆动态悬挂，反锁制动和稳定性控制应用。由于这些决定性应用，市场需要一种可靠的具有低干扰潜伏响应的费用-效能控制器，服务大量时间和事件驱动的在实时应用需要的集成外围的能力，具有在单一程序包中高出平均处理功率的中央处理器。拥有操作不可预测的设备的经济和法律风险是很高的。一旦进入市场，尤其任务决定性应用诸如自动驾驶仪或反锁制动系统，错误将是财力上所禁止的。重新设计的费用可以高达500K 美元，如果产品族享有同样内核或外围设计缺陷的话，费用会更高。另外，部件的替代品领域是极其昂贵的，因为设备要用来把模块典型地焊接成一个总体的价值比各个部件高几倍。为了缓和这些问题，在最坏的环境和电压条件下对这些单片机进行无论在部件级别还是系统级别上的综合测试是必需的。Intel Chandler 平台工程组提供了各种单片机和处理器的系统验证。这种系统的验证处理可以被分解为三个主要部分。系统的类型和应用需求决定了能够在设备上执行的测试类型。
1.2 AT89C51提供以下标准功能：
4k 字节FLASH 闪速存储器，128 字节内部RAM，32 个I/O 口线，2 个16 位定时/计数器，一个5 向量两级中断结构，一个全双工串行通信口，片内振荡器及时钟电路。同时，AT89C51 降至0Hz 的静态逻辑操作，并支持两种可选的节电工作模式。空闲方式体制CPU 的工作，但允许RAM，定时/计数器，串行通信口及中断系统继续工作。掉电方式保存RAM 中的内容，但振荡器体制工作并禁止其他所有不见工作直到下一个硬件复位。
图1-2-1 AT89C51 方框图
1.3引脚功能说明
·Vcc：电源电压
·GND：地
·P0 口：P0 口是一组8 位漏极开路型双向I/O 口，也即地址/数据总线复用。作为输出口用时，每位能吸收电流的方式驱动8 个TTL 逻辑门电路，对端口写“1”可作为高阻抗输入端用。在访问外部数据存储器或程序存储器时，这组口线分时转换地址（低8 位）和数据总线复用，在访问期间激活内部上拉电阻。在Flash 编程时，P0 口接受指令字节，而在程序校验时，输出指令字节，校验时，要求外接上拉电阻。
·P1 口：P1 是一个带内部上拉电阻的8 位双向I/O 口，P1 的输出缓冲级可驱动（吸收或输出电流）4 个TTL 逻辑门电路。对端口写“1”，通过内部的上拉电阻把端口拉到高电平，此时可作输入口。作为输入口使用时，因为内部存在上拉电阻，某个引脚被外部信号拉低时会输出一个电流（IIL）。Flash 编程和程序校验期间，P1 接受低8 位地址。
·P2 口：P2 是一个带有内部上拉电阻的8 位双向I/O 口，P2 的输出缓冲级可驱动（吸收或输出电流）4 个TTL 逻辑门电路。对端口写“1”，通过内部的上拉电阻把端口拉到高电平，此时可作输入口。作为输入口使用时，因为内部存在上拉电阻，某个引脚被外部信号拉低时会输出一个电流（IIL）。在访问外部程序存储器或16 位四肢的外部数据存储器（例如执行MOVX @DPTR指令）时，P2 口送出高8 位地址数据，在访问8 位地址的外部数据存储器（例如执行MOVX @ RI 指令）时，P2 口线上的内容（也即特殊功能寄存器（SFR）区中R2 寄存器的内容），在整个访问期间不改变。Flash 编程和程序校验时，P2 也接收高位地址和其他控制信号。
·P3 口：P3 是一个带有内部上拉电阻的8 位双向I/O 口，P3 的输出缓冲级可驱动（吸收或输出电流）4 个TTL 逻辑门电路。对端口写“1”，通过内部的上拉电阻把端口拉到高电平，此时可作输入口。作为输入口使用时，因为内部存在上拉电阻，某个引脚被外部信号拉低时会输出一个电流（IIL）。P3 口还接收一些用于Flash 闪速存储器编程和程序校验的控制信号。
·RST：复位输入。当振荡器工作时，RST 引脚出现两个机器周期以上高电平将使单片机复位。
·ALE/PROG：当访问外部程序存储器或数据存储器时，ALE（地址锁存允许）输出脉冲用于锁存地址的低8 位字节。即使不访问外部存储器，ALE 仍以时钟振荡频率的1/6 输出固定的正脉冲信号，因此它可对外输出时钟或用于定时目的。要注意的是，每当访问外部数据存储器时将跳过一个ALE 脉冲。对Flash 存储器编程期间，该引脚还用于输入编程脉冲（PROG）。如有必要，可通过对特殊功能寄存器（SFR）区中的8EH 单元D0 位置位，可禁止ALE 操作。该位置位后，只有一条MOVX 和MOVC 指令ALE 才会被激活。此外，该引脚会被微弱拉高，单片机执行外部程序时，应设置ALE 无效。
·PSEN：程序存储允许输出是外部程序存储器的读选通型号，当89C51 由外部存储器取指令（或数据）时，每个机器周期两次PSEN 有效，即输出两个脉冲。在此期间，当访问外部数据存储器，这两次有效的PSEN 信号不出现。
·EA/VPP：外部访问允许。欲使CPU 仅访问外部程序存储器（地址为
0000H—FFFFH），EA 端必须保持低电平（接地）。需注意的是：如果加密位LB1 被编程，复位时内部会锁存EA 端状态。如EA 端为高电平（接Vcc 端），CPU 则执行内部程序存储器中的指令。Flash 存储器编程时，该引脚加上+12v 的编程允许电源Vpp，当然这必须是该器件使用12v 编程电压Vpp。
·XTAL1：振荡器反相放大器及内部时钟发生器的输入端。
·XTAL2：振荡器反相放大器的输出端。89C51 中有一个用于构成内部振荡器的高增益反相放大器，引脚XTAL1 和XTAL2分别是该放大器的输入端和输出端。这个放大器与作为反馈元件的片外石英晶体或陶瓷谐振器一起构成自激振荡器，振荡电路参见图5。外接石英晶体或陶瓷谐振器及电容C1、C2 接在放大器的反馈回路中构成并联振荡电路。对电容C1、C2 虽没有十分严格的要求，但电容容量的大小会轻微影响振荡频率的高低、振荡器工作的稳定性、起振的难易程度及温度稳定性，如果使用石英晶体，我们推荐电容使用30Pf±10 Pf，而如使用陶瓷谐振器建议选择40Pf±10Pf。用户也可以采用外部时钟。这种情况下，外部时钟脉冲接到XTAL1 端，即内部时钟发生器的输入端XTAL2 则悬空。
·掉电模式：
在掉电模式下，振荡器停止工作，进入掉电模式的指令是最后一条被执行的指令，片内RAM 和特殊功能寄存器的内容在终止掉电模式前被冻结。推出掉电模式的唯一方法是硬件复位，复位后将重新定义全部特殊功能寄存器但不改变RAM 中的内容，在Vcc 恢复到正常工作电平前，复位应无效，且必须保持一定时间以使振荡器重启动并稳定工作。89C51 的程序存储器阵列是采用字节写入方式编程的，每次写入一个字符，要对整个芯片的EPROM 程序存储器写入一个非空字节，必须使用片擦除的方法将整个存储器的内容清楚。
2 编程方法
编程前，设置好地址、数据及控制信号，编程单元的地址加在P1 口和P2 口的P2.0—P2.3（11 位地址范围为0000H——0FFFH），数据从P0口输入，引脚P2.6、P2.7 和P3.6、P3.7 的电平设置见表6，PSEB 为低电平，RST保持高电平，EA/Vpp 引脚是编程电源的输入端，按要求加上编程电压，ALE/PROG引脚输入编程脉冲（负脉冲）。编程时，可采用4—20MHz 的时钟振荡器，89C51 编程方法如下：在地址线上加上要编程单元的地址信号在数据线上加上要写入的数据字节。激活相应的控制信号。在高电压编程方式时，将EA/Vpp 端加上+12v 编
程电压。每对Flash 存储阵列写入一个字节或每写入一个程序加密位，加上一个ALE/PROG 编程脉冲。改变编程单元的地址和写入的数据，重复1—5 步骤，知道全部文件编程结束。每个字节写入周期是自身定时的，通常约为1.5ms。·数据查询89C51 单片机用数据查询方式来检测一个写周期是否结束，在一个写周期中，如需要读取最后写入的那个字节，则读出的数据的最高位（P0.7）是原来写入字节的最高位的反码。写周期开始后，可在任意时刻进行数据查询。
2.1Ready/Busy:
字节编程的进度可通过Ready/Busy 输出信号检测，编程期间，ALE 变为高电平“H”后P3.4（Ready/Busy）端被拉低，表示正在编程状态（忙状态）。编程完成后，P3.4 变为高电平表示准备就绪状态。
·程序校验：如果加密位LB、LB2 没有进行编程，则代码数据可通过地址和数据线读回原编写的数据，采用下图的电路，程序存储器的地址由P1 口和P2 口的P2.0—P2.3 输入，数据由P0 口读出，P206、P2.7 和P3.6、P3.7 的控制信号见表6，PSEN 保持低电平，ALE、EA 和RST 保持高电平。校验时，P0 口必须接上10k 左右的上拉电阻。
图2-1-1 编程电路
图2-2-2 校验电路
2.2芯片擦除:
利用控制信号的正确组合(表6)并保持ALE/PROG 引脚10ms 的低电平脉冲宽度即可将EPROM 阵列(4k 字节)和三个加密位整片擦除,代码阵列在片擦除操作中将任何非空单元写入”1”,这步骤需在编程之前进行。
2.3读片内签名字节:
89C51 单片机内有3 个签名字节,地址为030H、031H 和032H。于声明该器件的厂商、号和编程电压。读签名字节的过程和单元030H、031H 和032H的正常校验相仿，只需要将P3.6 和P3.7 保持低电平，返回值意义如下：(030H) = 1EH 声明产品由ATMEL 公司制造。
(031H) = 51H 声明为89C51 单片机。
(032H) = FFH 声明为12V 编程电压。
(032H) = 05H 声明为5 编程电压。
2.4 编程接口：
采用控制信号的正确组合可对Flash 闪速存储阵列中的每一代码字节进行
写入和存储器的整片擦除，写操作周期是自身定时的，初始化后它将自动定时到操作完成。微机接口实现两种信息形式的交换。在计算机之外，由电子系统所处理的信息以一种物理信号形式存在，但在程序中，它是用数字表示的。任一接口的功能都可分为以某种形式进行数据库变换的一些操作，所以外部和内部形式的转换是由许多步骤完成的。模拟-数字转换器（ADC）用来将连续变化信号变成相应的数字量，这数字量可是可能性的二进制数值中的一固定值。如果传感器输出不是连续变化的，就不需模拟-数字转换。这种情况下，信号调理单元必须将输入信号变换成为另一信号，也可直接与接口的下一部分，即微计算机本身的输入输出单元相连接。输出接口采用相似的形式，明显的差别在于信息流的方向相反；是从程序到外部世界。这种情况下，程序可称为输出程序，它监督接口的操作并完成数字-模拟转换器（DAC）所需数字的标定。该子程序依次送出信息给输出器件，产生相应的电信号，由DAC 转换成模拟形式。最后，信号经调理（通常是放大）以形成适应于执行器操作的形式。在微机电路中使用的信号几乎总是太小而不能被直接地连到“外部世界”，因而必须用某种形式将其转换成更适宜的形式。接口电路部分的设计是使用微机的工程师所面临最重要的任务之一。我们已经了解到微机中，信号以离散的位形式表示。当微机要与只有打开或关闭操作的设备相连时，这种数字形式是最有用的，这里每一位都可表示一开关或执行器的状态。为了解决实际问题，一个单片机不仅包括CPU，程序和数据存储器，另外，它必须含有通过CPU 访问外部信息的硬件。一旦CPU 收集到数据信息和流程，它必须能够改变外部领域的一部分，这些硬件设备称作外围设备，它们是CPU 通往外部的窗口。
单片机可利用外围设备中最基本的用于一般用途的I/O 接口，每个I/O 接口既可作为输入端又可作为输出端，每个I/O 接口的功能取决与程序初始化阶段对数据方位寄存器相应位进行置一和清零操作，通过CPU 指令对数据寄存器相应位进行置一和清零来置一和清零输出端口，同样输入端口逻辑位也可以通过CPU 指令访问。一些类型的串行口单元允许CPU 与外部设备进行串口通信，用串口位代替平行位进行通信需要少许的I/O 口，这样使通信费用降低但速度也相对慢些。串口传送可以同步也可以异步。
The General Situation of A T89C51
Chapter 1 The application of A T89C51 Microcontrollers are used in a multitude of commercial applications such as modems, motor-control systems, air conditioner control systems, automotive engine and among others. The high processing speed and enhanced peripheral set of these microcontrollers make them suitable for such high-speed event-based applications. However, these critical application domains also require that these microcontrollers are highly reliable. The high reliability and low market risks can be ensured by a robust testing process and a proper tools environment for the validation of these microcontrollers both at the component and at the system level. Intel Pla tform Engineering department developed an object-oriented multi-threaded test environment for the validation of its AT89C51 automotive microcontrollers. The goals of this environment was not only to provide a robust testing environment for the AT89C51 automotive microcontrollers, but to develop an environment which can be easily extended and reused for the validation of several other future microcontrollers. The environment was developed in conjunction with Microsoft Foundation Classes (AT89C51). The paper describes the design and mechanism of this test environment, its interactions with various hardware/software environmental components, and how to use AT89C51.
1.1 Introduction
The 8-bit AT89C51 CHMOS microcontrollers are designed to handle high-speed calculations and fast input/output operations. MCS 51 microcontrollers are typically used for high-speed event control systems. Commercial applications include modems, motor-control systems, printers, photocopiers, air conditioner control systems, disk drives, and medical instruments. The automotive industry use MCS 51 microcontrollers in engine-control systems, airbags, suspension systems, and antilock braking systems (ABS). The AT89C51 is especially well suited to applications that benefit from its processing speed and enhanced on-chip peripheral functions set, such as automotive power-train control, vehicle dynamic suspension, antilock braking, and stability control applications. Because of these critical applications, the market requires a reliable cost-effective controller with a low interrupt latency response, ability to service the high number of time and event driven integrated peripherals
needed in real time applications, and a CPU with above average processing power in a single package. The financial and legal risk of having devices that operate unpredictably is very high. Once in the market, particularly in mission critical applications such as an autopilot or anti-lock braking system, mistakes are financially prohibitive. Redesign costs can run as high as a $500K, much more if the fix means 2 back annotating it across a product family that share the same core and/or peripheral design flaw. In addition, field replacements of components is extremely expensive, as the devices are typically sealed in modules with a total value several times that of the component. To mitigate these problems, it is essential that comprehensive testing of the controllers be carried out at both the component level and system level under worst case environmental and voltage conditions. This complete and thorough validation necessitates not only a well-defined process but also a proper environment and tools to facilitate and execute the mission successfully. Intel Chandler Platform Engineering group provides post silicon system validation (SV) of various micro-controllers and processors. The system validation process can be broken into three major parts. The type of the device and its application requirements determine which types of testing are performed on the device.
1.2 The AT89C51 provides the following standard features:
4Kbytes of Flash, 128 bytes of RAM, 32 I/O lines, two 16-bittimer/counters, a five vector two-level interrupt architecture, a full duple serial port, on-chip oscillator and clock circuitry. In addition, the AT89C51 is designed with static logic for operation down to zero frequency and supports two software selectable power saving modes. The Idle Mode stops the CPU while allowing the RAM, timer/counters, serial port and interrupt sys -tem to continue functioning. The Power-down Mode saves the RAM contents but freezes the oscillator disabling all other chip functions until the next hardware reset.
Figure 1-2-1Block Diagram
1-3Pin Description
VCC Supply voltage.
GND Ground.
Port 0：Port 0 is an 8-bit open-drain bi-directional I/O port. As an output port, each pin can sink eight TTL inputs. When 1s are written to port 0 pins, the pins can be used as high impedance inputs .Port 0 may also be configured to be the multiplexed low order address/data bus during accesses to external program and data memory. In this mode P0 has internal pullups. Port 0 also receives the code bytes during Flash
programming, and outputs the code bytes during program verification. External pullups are required during program verification.
Port 1：Port 1 is an 8-bit bi-directional I/O port with internal pullups. The Port 1 output buffers can sink/source four TTL inputs. When 1s are written to Port 1 pins they are pulled high by the internal pullups and can be used as inputs. As inputs, Port 1 pins that are externally being pulled low will source current (IIL) because of the internal pullups. Port 1 also receives the low-order address bytes during Flash programming and verification.
Port 2：Port 2 is an 8-bit bi-directional I/O port with internal pullups. The Port 2 output buffers can sink/source four TTL inputs. When 1s are written to Port 2 pins they are pulled high by the internal pullups and can be used as inputs. As inputs, Port 2 pins that are externally being pulled low will source current (IIL) because of the internal pullups. Port 2 emits the high-order address byte during fetches from external program memory and during accesses to Port 2 pins that are externally being pulled low will source current (IIL) because of the internal pullups. Port 2 emits the high-order address byte during fetches from external program memory and during accesses to external data memory that use 16-bit addresses (MOVX@DPTR). In this application, it uses strong internal pull-ups when emitting 1s. During accesses to external data memory that use 8-bit addresses (MOVX @ RI), Port 2 emits the contents of the P2 Special Function Register. Port 2 also receives the high-order address bits and some control signals during Flash programming and verification.
Port 3：Port 3 is an 8-bit bi-directional I/O port with internal pull ups. The Port 3 output buffers can sink/source four TTL inputs. When 1s are written to Port 3 pins they are pulled high by the internal pullups and can be used as inputs. As inputs, Port 3 pins that are externally being pulled low will source current (IIL) because of the pullups.
Port 3 also serves the functions of various special feature soft the AT89C51 as listed below:
RST：Reset input. A high on this pin for two machine cycles while the oscillator is running resets the device.
ALE/PROG：Address Latch Enable output pulse for latching the low byte of the address during accesses to external memory. This pin is also the program pulse input (PROG) during Flash programming. In normal operation ALE is emitted at a constant rate of 1/6 the oscillator frequency, and may be used for external timing or clocking purposes. Note, however, that one ALE pulse is skipped during each access to
external Data Memory. If desired, ALE operation can be disabled by setting bit 0 of SFR location 8EH. With the bit set, ALE is active only during a MOVX or MOVC instruction. Otherwise, the pin is weakly pulled high. Setting the ALE-disable bit has no effect if the microcontroller is in external execution mode.
PSEN：Program Store Enable is the read strobe to external program memory. When theAT89C51 is executing code from external program memory, PSEN is activated twice each machine cycle, except that two PSEN activations are skipped during each access to external data memory.
EA/VPP：External Access Enable. EA must be strapped to GND in order to enable the device to fetch code from external program memory locations starting at 0000H up to FFFFH. Note, however, that if lock bit 1 is programmed, EA will be internally latched on reset. EA should be strapped to VCC for internal program executions. This pin all receives the 12-volt programming enable voltage (VPP) during Flash programming, for parts that require 12-volt VPP.
XTAL1：Input to the inverting oscillator amplifier and input to the internal clock operating circuit.
XTAL2:Output from the inverting oscillator amplifier. Oscillator CharacteristicsXTAL1 and XTAL2 are the input and output, respectively, of an inverting amplifier which can be configured for use as an on-chip oscillator, as shown in Figure 1. Either a quarts crystal or ceramic resonator may be used. To drive the device from an external clock source, XTAL2 should be left unconnected while XTAL1 is driven as shown in Figure 2.There are no requirements on the duty cycle of the external clock signal, since the input to the internal clocking circuitry is through a divide-by-two flip-flop, but minimum and maximum voltage high and low time specifications must be observed.Idle Mode In idle mode, the CPU puts itself to sleep while all the on chip peripherals remain active. The mode is invoked by software. The content of the on-chip RAM and all the special functions registers remain unchanged during this mode. The idle mode can be terminated by any enabled interrupt or by a hardware reset. It should be noted that when idle is terminated by a hard ware reset, the device normally resumes program execution,from where it left off, up to two machine cycles before the internal reset algorithm takes control. On-chip hardware inhibits access to internal RAM in this event, but access to the port pins is not inhibited. To eliminate the possibility of an unexpected write to a port pin when Idle is terminated by reset, the instruction following the one that invokes Idle should not be one that writes to a port pin or to external memory.
Power-down Mode
In the power-down mode, the oscillator is stopped, and the instruction that invokes power-down is the last instruction executed. The on-chip RAM and Special Function Registers retain their values until the power-down mode is terminated. The only exit from power-down is a hardware reset. Reset redefines the SFR but does not change the on-chip RAM. The reset should not be activated before VCC is restored to its normal operating level and must be held active long enough to allow the oscillator to restart and stabilize. The AT89C51 code memory array is programmed byte-by byte in either programming mode. To program any nonblank byte in the on-chip Flash Memory, the entire memory must be erased using the Chip Erase Mode.
2 Programming Algorithm
Before programming the AT89C51, the address, data and control signals should be set up according to the Flash programming mode table and Figure 3 and Figure 4. To program the AT89C51, take the following steps.1. Input the desired memory location on the address lines.2. Input the appropriate data byte on the data lines. 3. Activate the correct combination of control signals. 4. Raise EA/VPP to 12V for the high-voltage programming mode. 5. Pulse ALE/PROG once to program a byte in the Flash array or the lock bits. The byte-write cycle is self-timed and typically takes no more than 1.5 ms. Repeat steps 1 through 5, changing the address and data for the entire array or until the end of the object file is reached. Data Polling: The AT89C51 features Data Polling to indicate the end of a write cycle. During a write cycle, an attempted read of the last byte written will result in the complement of the written datum on PO.7. Once the write cycle has been completed, true data are valid on all outputs, and the next cycle may begin. Data Polling may begin any time after a write cycle has been initiated.
2.1Ready/Busy:
The progress of byte programming can also be monitored by the RDY/BSY output signal. P3.4 is pulled low after ALE goes high during programming to indicate BUSY. P3.4 is pulled high again when programming is done to indicate READY.
Program Verify:
If lock bits LB1 and LB2 have not been programmed, the programmed code data can be read back via the address and data lines for verification. The lock bits cannot be verified directly. Verification of the lock bits is achieved by observing that their features are enabled.
Figure 2-1-1 Programming the Flash
Figure 2-2-2 Verifying the Flash
2.2 Chip Erase:
The entire Flash array is erased electrically by using the proper combination of control signals and by holding ALE/PROG low for 10 ms. The code array is written with all “1”s. The chip erase operation must b e executed before the code memory can be re-programmed.
2.3 Reading the Signature Bytes:
The signature bytes are read by the same procedure as a normal verification of locations 030H, 031H, and 032H, except that P3.6 and P3.7 must be pulled to a logic low. The values returned areas follows :
(030H) = 1EH indicates manufactured by Atmel
(031H) = 51H indicates 89C51
(032H) = FFH indicates 12V programming
(032H) = 05H indicates 5V programming
2.4 Programming Interface
Every code byte in the Flash array can be written and the entire array can be erased by using the appropriate combination of control signals. The write operation cycle is self timed and once initiated, will automatically time itself to completion. A microcomputer interface converts information between two forms. Outside the microcomputer the information handled by an electronic system exists as a physical signal, but within the program, it is represented numerically. The function of any interface can be broken down into a number of operations which modify the data in some way, so that the process of conversion between the external and internal forms is carried out in a number of steps. An analog-to-digital converter is used to convert a continuously variable signal to a corresponding digital form which can take any one of a fixed number of possible binary values. If the output of the transducer does not vary continuously, no ADC is necessary. In this case the signal conditioning section must convert the incoming signal to a form which can be connected directly to the next part of the interface, the input/output section of the microcomputer itself. Output interfaces take a similar form, the obvious difference being that here the flow of information is in the opposite direction; it is passed from the program to the outside world. In this case the program may call an output subroutine which supervises the operation of the interface and performs the scaling numbers which may be needed for
digital-to-analog converter. This subroutine passes information in turn to an output device which produces a corresponding electrical signal, which could be converted into analog form using a DAC. Finally the signal is conditioned to a form suitable for operating an actuator.The signals used within microcomputer circuits are almost always too small to be connected directly to the outside world” and some kind of interface must be used to translate them to a more appropriate form. The design of section of interface circuits is one of the most important tasks facing the engineer wishing to apply microcomputers. We have seen that in microcomputers information is represented as discrete patterns of bits; this digital form is most useful when the microcomputer is to be connected to equipment which can only be switched on or off, where each bit might represent the state of a switch or actuator. To solve real-world problems, a microcontroller must have more than just a CPU, a program, and a data memory. In addition, it must contain hardware allowing the CPU to access information from the outside world. Once the CPU gathers information and processes the data, it must also be able to effect change on some portion of the outside world. These hardware devices, called peripherals, are the CPU’s window to the outside.
The most basic form of peripheral available on microcontrollers is the general purpose I70 port. Each of the I/O pins can be used as either an input or an output. The function of each pin is determined by setting or clearing corresponding bits in a corresponding data direction register during the initialization stage of a program. Each output pin may be driven to either a logic one or a logic zero by using CPU instructions to pin may be viewed (or read.) by the CPU using program instructions. Some type of serial unit is included on microcontrollers to allow the CPU to communicate bit-serially with external devices. Using a bit serial format instead of bit-parallel format requires fewer I/O pins to perform the communication function, which makes it less expensive, but slower. Serial transmissions are performed either synchronously or asynchronously.
AT89C51单片机外文翻译
AT89C51外文翻译 Description The AT89C51 is a low-power, high-performance CMOS 8-bit microcomputer with 4K bytes of Flash Programmable and Erasable Read Only Memory (PEROM). The device is manufactured using Atmel’s high density nonvolatile memory technology and is compatible with the industry standard MCS-51? instruction-set and pinout. The on-chip Flash allows the program memory to be reprogrammed in-system or by a conventional nonvolatile memory programmer. By combining a versatile 8-bit CPU with Flash on a monolithic chip, the Atmel AT89C51 is a powerful microcomputer which provides a highly flexible and cost effective solution to many embedded control applications. Features ? Compatible with MCS-51? Products ? 4K Bytes of In-System Reprogrammable Flash Memory – Endurance: 1,000 Write/Erase Cycles ? Fully Static Operation: 0 Hz to 24 MHz ? Three-Level Program Memory Lock ? 128 x 8-Bit Internal RAM ? 32 Programmable I/O Lines ? Two 16-Bit Timer/Counters ? Six Interrupt Sources ? Programmable Serial Channel ? Low Power Idle and Power Down Modes The AT89C51 provides the following standard features: 4K bytes of Flash,128 bytes of RAM, 32 I/O lines, two 16-bit timer/counters, a five vector two-level interrupt architecture, a full duplex serial port, on-chip oscillator and clock circuitry. In addition, the AT89C51 is designed with static logic for operation down to zero frequency and supports two software selectable power saving modes. The Idle Mode stops the CPU while allowing the RAM, timer/counters, serial port and interrupt system to continue functioning. The Power-down Mode saves the RAM contents but freezes the oscillator disabling all other chip functions until the next hardware reset.
步进电机及单片机英文文献及翻译
外文文献： Knowledge of the stepper motor What is a stepper motor： Stepper motor is a kind of electrical pulses into angular displacement of the implementing agency. Popular little lesson: When the driver receives a step pulse signal, it will drive a stepper motor to set the direction of rotation at a fixed angle (and the step angle). You can control the number of pulses to control the angular displacement, so as to achieve accurate positioning purposes; the same time you can control the pulse frequency to control the motor rotation speed and acceleration, to achieve speed control purposes. What kinds of stepper motor sub-： In three stepper motors: permanent magnet (PM), reactive (VR) and hybrid (HB) permanent magnet stepper usually two-phase, torque, and smaller, step angle of 7.5 degrees or the general 15 degrees; reaction step is generally three-phase, can achieve high torque output, step angle of 1.5 degrees is generally, but the noise and vibration are large. 80 countries in Europe and America have been eliminated; hybrid stepper is a mix of permanent magnet and reactive advantages. It consists of two phases and the five-phase: two-phase step angle of 1.8 degrees while the general five-phase step angle of 0.72 degrees generally. The most widely used Stepper Motor. What is to keep the torque (HOLDING TORQUE) How much precision stepper motor? Whether the cumulative： The general accuracy of the stepper motor step angle of 3-5%, and not cumulative.
会计内部控制中英文对照外文翻译文献
会计内部控制中英文对照外文翻译文献(文档含英文原文和中文翻译)
内部控制透视：理论与概念 摘要：内部控制是会计程序或控制系统，旨在促进效率或保证一个执行政策或保护资产或避免欺诈和错误。内部是一个组织管理的重要组成部分。它包括计划、方法和程序使用，以满足任务，目标和目的，并在这样做，支持基于业绩的管理。内部控制是管理阶层的平等与控制可以帮助管理者实现资源的预期的有效管理的结果通过。内部控制应减少或违规错误的风险关联未被发现的，但设计和建立有效的内部控制不是一个简单的任务，不可能是一个实现通过快速修复短套。在此讨论了内部文件的概念的不同方面的内部控制和管制。 关键词：内部控制，管理控制，控制环境，控制活动，监督 1、介绍 环境需要新的业务控制变量不为任何潜在的股东和管理人士的响应因子为1，另外应执行/她组织了一个很大的控制权。控制是管理活动的东西或以上施加控制。思想的产生和近十年的发展需要有系统的商业资源和控制这种财富一个新的关注。主题之一热一回合管制的商业资源是分析每个控制成本效益。 作为内部控制和欺诈的第一道防线，维护资产以及预防和侦查错误。内部控制，我们可以说是一种控制整个系统的财务和其他方面的管理制定了为企业的顺利运行;它包括内部的脸颊，内部审计和其他形式的控制。 COSO的内部控制描述如下。内部控制是一个客观的方法用来帮助确保实现。在会计和组织理论，内部控制是指或目标目标的过程实施由组织的结构，工作和权力流动，人员和具体的管理信息系统，旨在帮助组织实现。这是一种手段，其中一个组织的资源被定向，监控和测量。它发挥着无形的（重要的作用，预防和侦查欺诈和保护组织的资源，包括生理（如，机械和财产）和乙二醇，声誉或知识产权，如商标）。在组织水平，内部控制目标与可靠性的目标或战略的财务报告，及时反馈业务上的成就，并遵守法律，法规。在具体的交易水平，内部控制是指第三方采取行动以实现一个具体目标（例如，如何确保本组织的款项，在申请服务提供有效的。）内部控制程序reduce程变异，导
单片机外文翻译
杭州电子科技大学信息工程学院毕业设计（论文）外文文献翻译 毕业设计（论文）题目用单片机实现的数字时钟电路设计文献综述题目单片机控制系统系电子工程 专业电子信息科学与技术 姓名郭筱楠 班级08091911 学号08919115 指导教师王维平
单片机控制系统 广义地说，微型计算机控制系统（单片机控制系统）是用于处理信息的，这种被用于处理的信息可以是电话交谈，也可以是仪器的读数或者是一个企业的帐户，但是各种情况下都涉及到相同的主要操作：信息的处理、信息的存储和信息的传递。在常规的电子设计中，这些操作都是以功能平台方式组合起来的，例如计数器，无论是电子计数器还是机械计数器，都要存储当前的数值，并且按要求将该数值增加1。一个系统例如采用计数器的电子钟之类的任一系统要使其存储和处理能力遍布整个系统，因为每个计数器都能存储和处理一些数字。 现如今，以微处理器为基础的系统从常规的处理方法中分离了出来，它将信息的处理，信息的存储和信息的传输三个功能分离形成不同的系统单元。这种主要将系统分成三个主要单元的分离方法是冯-诺依曼在20世纪40年代所设想出来的，并且是针对微计算机的设想。从此以后基本上所有制成的计算机都是用这种结构设计的，尽管他们包含着宽广的物理形式与物理结构，但从根本上来说他们均是具有相同基本设计的计算机。 在以微处理器为基础的系统中，处理是由以微处理器为基础的系统自身完成的。存储是利用存储器电路，而从系统中输入和输出的信息传输则是利用特定的输入/输出（I/O）电路。要在一个以微处理器为基础的时钟中找出执行具有计数功能的一个特殊的硬件组成部分是不可能的，因为时间存储在存储器中，而在固定的时间间隔下由微处理器控制增值。但是，规定系统运转过程的软件却规定了包含实现计数器计数功能的单元部分。由于系统几乎完全由软件所定义，所以对微处理器结构和其辅助电路这种看起来非常抽象的处理方法使其在应用时非常灵活。这种设计过程主要是软件工程，而且在生产软件时，就会遇到产生于常规工程中相似的构造和维护问题。 图1.1 微型计算机的三个组成部分 图1.1显示出了微型计算机中这三个单元在一个微处理器控制系统中是如何按照机器中的信息通信方式而联接起来的。该系统由微处理器控制，微处理器能够对其自身的存储器和输入/输出单元的信息传输进行管理。外部的连接部分与
外文翻译--如何监测内部控制
附录A
附录B 如何监测内部控制 内部控制是任何组织有效运行的关键,董事会、执行长和内部审计人员都为实现这个企业的目标而工作;该内部控制系统是使这些团体确保那些目标的达成的一种手段。控制帮助一个企业有效率地运转。此外,运用一种有效的风险系统,风险可被降低到最小。同时,控制促进经营和与经营有关的信息的可靠性。全美反舞弊性财务报告委员会发起组织(COSO；1992) 在它发布的具有开创性的文件《内部控制整合框架》中,将内部控制定义为：企业风险管理是一个过程，受企业董事会、管理层和其他员工的影响，包括内部控制及其在战略和整个公司的应用，旨在为实现经营的效率和效果、财务报告的可靠性以及法规的遵循提供合理保证。该委员会还指出,一个的内部控制的系统包括五个要素。它们是：控制环境、风险评估、信息和沟通、控制活动、监控。 COSO的定义及五个要素已被证明确实对不同的团体,如董事会和首席执行官起到作用。这些群体对内部控制系统的监管以及系统设计与运行有责任。而且,内部审计人员已经发现COSO的指导是有用的。这群人员可能会被董事会或管理层要求去测试控制。COSO最近发布的一份讨论文件，指出五个要素监控,其中的五个要素的确定在1992 frame work COSO原本。中国发展简报的题为《内部控制-整合框架：内部控制体系监督指南》(COSO，2007)。在文件中,COSO 强调监控的重要性，以及这些信息常常被没有充分利用。 因为董事会、执行长,和内部审计人员都在一个公司的内部控制中扮演着重要角色，内部控制的各要素,包括监测,都对所有的团体有着非常重要的意义。同时,外审计人员对监测有兴趣。《萨班斯-奥克斯利法案》（2002）为外部审计师创建了一个新的监督体制。所有的五个要素,包括监测,必须加以考虑。另外,内部控制审计必须结合对财务报告的检查。在一体化审计之前，在首席执行官的领导下，也许也在内部审计活动的支持下的管理，评估了内控制体系的有效性。随后外部审计人员对控制出具意见。起监督角色的董事会，将阅读内部审计、管理层和首席执行官出具的报告。文件关于监测对每一个团体的指导起了帮助,因为他们分别为各自的角色而劳动。 第一，什么是监测。监测的组成可评估内部控制系统在过去一段时间发挥效用的质量。其对控制功能的评估有助于企业确定其控制在有效地运作中。在执行监测活动时，相关人员参与审查系统的设计及其运行效果。这种检查必须进行及时,目的是为了提供给企业最大的利益。管理层负责做出适当的行动以回应这些结果。当事人对内部控制有兴趣,可以充分依赖这个内部控制系统,如果合适的监
51单片机外文文献
The Introduction of AT89C51 Description The AT89C51 is a low-power, high-performance CMOS 8-bit microcomputer with 4K bytes of Flash programmable and erasable read only memory (PEROM). The device is manufactured using Atmel’s high-density nonvolatile memory technology and is compatible with the industry-standard MCS-51 instruction set. The on-chip Flash allows the program memory to be reprogrammed in-system or by a conventional nonvolatile memory programmer. By combining a versatile 8-bit CPU with Flash on a monolithic chip, the Atmel AT89C51 is a powerful microcomputer which provides a highly-flexible and cost-effective solution to many embedded control applications. Function characteristic The AT89C51 provides the following standard features: 4K bytes of Flash, 128 bytes of RAM, 32 I/O lines, two 16-bit timer/counters, one 5 vector two-level interrupt architecture, a full duplex serial port, one-chip oscillator and clock circuitry. In addition, the AT89C51 is designed with static logic for operation down to zero frequency and supports two software selectable power saving modes. The Idle Mode stops the CPU while allowing the RAM, timer/counters, serial port and interrupt system to continue functioning. The Power-down Mode saves the RAM contents but freezes the oscillator disabling all other chip functions until the next hardware reset. Pin Description VCC：Supply voltage. GND：Ground.
单片机外文文献翻译
外文文献一单片机简介 单片机是一种集成在电路芯片，是采用超大规模集成电路技术把具有数据处理能力的中央处理器CPU随机存储器RAM、只读存储器ROM、多种I/O口和中断系统、定时器/计时器等功能（可能还包括显示驱动电路、脉宽调制电路、模拟多路转换器、A/D转换器等电路）集成到一块硅片上构成的一个小而完善的计算机系统。单片机也被称为微控制器（Microcontroller），是因为它最早被用在工业控制领域。单片机由芯片内仅有CPU的专用处理器发展而来。最早的设计理念是通过将大量外围设备和CPU集成在一个芯片中，使计算机系统更小，更容易集成进复杂的而对体积要求严格的控制设备当中。INTEL的Z80是最早按照这种思想设计出的处理器，从此以后，单片机和专用处理器的发展便分道扬镳。 二、单片机的发展趋势 现在可以说单片机是百花齐放，百家争鸣的时期，世界上各大芯片制造公司都推出了自己的单片机，从8位、16位到32位，数不胜数，应有尽有，有与主流C51系列兼容的，也有不兼容的，但它们各具特色，互成互补，为单片机的应用提供广阔的天地。 纵观单片机的发展过程，可以预示单片机的发展趋势，大致有： 1.低功耗CMOS MCS-51系列的8031推出时的功耗达630mW，而现在的单片机普遍都在100mW左右，随着对单片机功耗要求越来越低，现在的各个单片机制造商基本都采用了CMOS(互补金属氧化物半导体工艺)。象80C51就采用了HMOS(即高密度金属氧化物半导体工艺)和CHMOS(互补高密度金属氧化物半导体工艺)。CMOS虽然功耗较低，但由于其物理特征决定其工作速度不够高，而CHMOS则具备了高速和低功耗的特点，这些特征，更适合于在要求低功耗象电池供电的应用场合。所以这种工艺将是今后一段时期单片机发展的主要途径。 2.微型单片化 现在常规的单片机普遍都是将中央处理器(CPU)、随机存取数据存储(RAM)、只读程序存储器(ROM)、并行和串行通信接口，中断系统、定时电路、时钟电路集成在一块单一的芯片上，增强型的单片机集成了如A/D转换器、PMW(脉宽调制电路)、WDT(看门狗)、有些单片机将LCD(液晶)驱动电路都集成在单一的芯片上，这样 单片机包含的单元电路就更多，功能就越强大。甚至单片机厂商还可以根据用户的要求量身定做，制造出具有． 自己特色的单片机芯片。此外，现在的产品普遍要求体积小、重量轻，这就要求单片机除了功能强和功耗低外，还要求其体积要小。现在的许多单片机都具有多种封装形式，其中SMD(表面封装)越来越受欢迎，使得由单片机构成的系统正朝微型化方向发展。 3.主流与多品种共存 现在虽然单片机的品种繁多，各具特色，但仍以80C51为核心的单片机占主流，兼容其结构和指令系统的有PHILIPS公司的产品，ATMEL公司的产品和中国台湾
中小企业内部控制_外文参考文献
中小企业内部控制_外文参考文献 安徽工业大学毕业设计外文翻译 Private Enterprises of the intenal control issues Pulin Chang Economic Review. 2008, (5) Third, the promotion of private SMEs in the internal control system strategy (A) change management and business owners the concept of development. The majority of private small and medium enterprises in the family business, the success of these enterprises depends largely on internal control or entrepreneur leadership attention and level of implementation. Over the years, by traditional Chinese culture, business owners believe in Sincerity, fraternal loyalty permeate many aspects of enterprise management, strengthen internal controls that will affect the organization the members of distrust, resulting in internal control. Many private business owners that rely on business to do business benefits out of, rather than out of the internal financial management control; that the market is the most important internal control will be bound himself and staff development. Understanding of the bias, so that these leaders neglected the internal control system on the production and operation activities. Internal control can really become the leader of the internal needs of enterprise internal control system is the key to whether a mere formality. The internal control to make the internal needs of the enterprise depends largely on two points: First, determine
单片机外文翻译--STC89C52处理芯片
外文资料翻译 STC89C52 processi ng chip Prime features: With MCS - 51 SCM product compatibility, 8K bytes in the system programmable Flash memory, 1000 times CaXie cycle, the static operation: 0Hz ~ 33Hz, triple encryption program memory, 32 programmed I/O port, three 16 timer/counter, the eight uninterrupted dual-career UART serial passage, low power consumption, leisure and fall after fall electric power mode can be awakened and continuous watchdog timer and double-number poin ter, power ide ntifier. Efficacy: characteristics STC89C52 is one kind of low power consumption, high CMOS8 bit micro-co ntroller, 8K in system programmable Flash memory. Use high-de nsity nonv olatile storage tech no logy, and in dustrial 80C51 product in structi on and pin fully compatible. The Flash memory chips allows programs in the system, also suitable for programmable conventional programming. In a single chip, have clever 8 bits CPU and on li ne system programmable Flash, in crease STC89C52 for many embedded control system to provide high vigorous application and useful solutions. STC89C52 has following standard efficacy: 8k byte Flash RAM, 256 bytes, 32 I/O port, the watchdog timer, two, three pointer numerical 16 timer/counter, a 6 vector level 2 continuous structure, the serial port, working within crystals and horological circuit. In addition, 0Hz AT89S52 can drop to the static logic operation, support two software can choose power saving mode. Idle mode, the CPU to stop working, and allows the RAM, timer/c oun ters, serial, continu ous to work. Protectio n asa na patter n, RAM content is survival, vibrators frozen, SCM, until all the work under a continuous or hardware reset. 8-bit microcontrollers 8K bytes in the system programmable Flash AT89S52 devices. Mouth: P0 P0 mouth is a two-way ope n drain I/O. As export, each can drive eight TTL logic level. For P0 port to write "1", foot as the high impeda nee in put. When access to exter nal programs and nu merical memory, also known as
单片机的外文文献及中文翻译
SCM is an integrated circuit chip, is the use of large scale integrated circuit technology to a data processing capability of CPU CPU random access memory RAM, read-only memory ROM, a variety of I / O port and interrupt system, timers / timer functions (which may also include display driver circuitry, pulse width modulation circuit, analog multiplexer, A / D converter circuit) integrated into a silicon constitute a small and complete computer systems. SCM is also known as micro-controller (Microcontroller), because it is the first to be used in industrial control. Only a single chip by the CPU chip developed from a dedicated processor. The first design is by a large number of peripherals and CPU on a chip in the computer system, smaller, more easily integrated into a complex and demanding on the volume control device which. The Z80 INTEL is the first designed in accordance with this idea processor, then on the development of microcontroller and dedicated processors will be parting ways. Are 8-bit microcontroller early or 4 bits. One of the most successful is the INTEL 8031, for a simple, reliable and good performance was a lot of praise. Then developed in 8031 out of MCS51 MCU Systems. SCM systems based on this system until now is still widely used. With the increased requirements of industrial control field, began a 16-bit microcontroller, but not ideal because the cost has not been very widely used. After 90 years with the great development of consumer electronics, microcontroller technology has been a huge increase. With INTEL i960 series, especially the later series of widely used ARM, 32-bit microcontroller quickly replace high-end 16-bit MCU status and enter the mainstream market. The traditional 8-bit microcontroller performance have been the rapid increase capacity increase compared to 80 the number of times. Currently, high-end 32-bit microcontroller clocked over 300MHz, the performance catching the mid-90s dedicated processor, while the average model prices fall to one U.S. dollar, the most high-end [1] model only 10 dollars. Modern SCM systems are no longer only in the development and use of bare metal environment, a large number of proprietary embedded operating system is widely used in the full range of SCM. The handheld computers and cell phones as the core processing of high-end microcontroller can even use a dedicated Windows and Linux operating systems. SCM is more suitable than the specific processor used in embedded systems, so it was up to the application. In fact the number of SCM is the world's largest computer. Modern human life used in almost every piece of electronic and mechanical products will be integrated single chip. Phone, telephone, calculator, home appliances, electronic toys, handheld computers and computer accessories such as a mouse with a 1-2 in both the Department of SCM. Personal computer will have a large number of SCM in the work. General car with more than 40 microcontroller, a complex industrial control systems may even hundreds of single chip at the same time work! SCM is not only far exceeds the number of PC and other computing the sum, or even more than the number of human beings. Single chip, also known as single-chip microcontroller, it is not complete a certain logic chips, but to a computer system integrated into a chip. Equivalent to a
外文翻译---51系列单片机的结构和功能
外文翻译---51系列单片机的结构和功能
外文资料翻译 英文原文： Structure and function of the MCS-51 series Structure and function of the MCS-51 series one-chip computer MCS-51 is a name of a piece of one-chip computer series which Intel Company produces. This company introduced 8 top-grade one-chip computers of MCS-51 series in 1980 after introducing 8 one-chip computers of MCS-48 series in 1976. It belong to a lot of kinds this line of one-chip computer the chips have such as 8051, 8031, 8751, 80C51BH, 80C31BH,etc., their basic composition, basic performance and instruction system are all the same. 8051 daily representatives- 51 serial one-chip computers . An one-chip computer system is made up of several following parts: (1) One microprocessor of 8 (CPU). (2) At slice data memory RAM (128B/256B),it use not depositing not can reading /data that write, such as result not middle of operation, final result and data wanted to show, etc. (3) Procedure memory ROM/EPROM (4KB/8KB ), is used to preserve the procedure , some initial data and form in slice. But does not take ROM/EPROM within some one-chip computers, such as 8031 , 8032, 80C ,etc.. (4) Four 8 run side by side I/O interface P0 four P3, each mouth can use as introduction, may use as exporting too. (5) Two timer / counter, each timer / counter may set up and count in the way, used to count to the external incident, can set up into a timing way too, and can according to count or result of timing realize the control of the computer. (6) Five cut off cutting off the control (universal asynchronous receiver/transmitter (UART) ), is it realize one-chip computer or one-chip computer and serial communication of computer to use for. (8) Stretch oscillator and clock produce circuit, quartz crystal finely tune electric capacity need outer. Allow oscillation frequency as 12 megahertz now at most. Every the above-mentioned part was joined through the inside data bus .Among them, CPU is a core of the one-chip computer, it is the control of the computer and command center, made up of such parts as arithmetic unit and controller , etc.. The arithmetic unit can carry on 8 persons of arithmetic operation and unit ALU of logic operation while including one, the 1 storing devices temporarily of 8, storing device 2 temporarily, 8's accumulation device ACC, register B and procedure state register PSW, etc. Person who accumulate ACC count by 2 input ends entered of checking etc. temporarily as one operation often, come from person who store 1 operation is it is it make operation to go on to count temporarily , operation result and loop back ACC with another one. In addition, ACC is often regarded as the transfer station of data transmission on 8051 inside. The same as general microprocessor, it is the busiest register. Help remembering that agreeing with a expresses in the order. The controller includes the procedure counter, the order is deposited, the