COIL
Power
At Pickup Voltage 137 mW ( 2A single side stable, 2 coil latching)
(typical)
98 mW (1 coil latching or 1A or 1AB single side stable)
Max. Continuous 0.75 W at 20°C (68°F) ambient Dissipation Temperature Rise 30°C (54°F) at nominal coil voltage 105°C (221°F)
Max. Temperature
CONTACTS
Arrangement
SPST (1 Form A), DPST (2 Form A)DPST (1 Form A and 1 Form B)Ratings
Resistive load:
Max. switched power:300 W or 2500 VA (SPST)
240 W or 2000 VA (DPST)
Max. switched current:10 A (SPST)
8 A (DPST)
Max. switched voltage: 150 VDC or 380 VAC**Note: If switching voltage is greater than 30 VDC,special precautions must be taken. Please contact the factory.
Rated Load SPST
UL, CUR 10 A at 250 VAC general use, 30k cycles
10 A at 30 VDC resistive, 30k cycles 1/3 HP at 250 VAC B300 Pilot Duty
DPST
8 A at 250 VAC general use, 30k cycles 8 A at 30 VDC resistive, 30k cycles 1/3 HP at 250 VAC
1/4 HP at 125 VAC
Material Silver nickel, gold plating optional
Resistance
< 50 milliohms initially (6 V 1 A voltage drop method)
GENERAL DATA
Life Expectancy
Minimum operations Mechanical 1 x 107
Electrical 1 x 106at 10 A 250 VAC resistive (SPST)Operate Time (typical) 5 ms at nominal coil voltage Release Time (typical)
3 ms at nominal coil voltage (with no coil suppression)Set Time (typical) 5 ms at nominal coil voltage Reset Time (typical)
4 ms at nominal coil voltage Dielectric Strength 4000 Vrms coil to contact (-1A, -1AB)(at sea level)
3000 Vrms coil to contact (-2A)1000 Vrms between contacts 2000 Vrms between contact sets Insulation Resistance 1000 megohms min. at 20°C 500 Vdc 50% RH
Dropout
Greater than 10% of nominal coil voltage Ambient Temperature
At nominal coil voltage
Operating -40°C (-40°F) to 70°C (158°F)Storage -40°C (-40°F) to 105°C (221°F)Vibration 0.062” DA at 10 to 55 Hz
Shock 10 g functional Enclosure P.B.T. polyester
Terminals
Tinned copper alloy, P.C.Max. Solder Temp.270°C (518°F)Max. Solder Time 5 seconds Max. Solvent Temp.80°C (176°F)Max. Immersion Time
30 seconds Weight
6 grams
?Dielectric strength 4000 Vrms
?Single and dual coil latching versions available ?Epoxy sealed version available ?10 Amp switching ?
UL, CUR file E44211
NOTES
1.All values at 20°C (68°F).
2.Relay may pull in with less than “Must Operate” value.
3.Relay has fixed coil polarity.
4.
For complete isolation between the relay’s magnetic fields, it is recommended that a .197" (5.0 mm) space be provided between adjacent relays.
5.Relay adjustment may be affected if undue pressure is exerted on relay case.
6.Specifications subject to change without notice.
RELAY ORDERING DATA AZ880
AZ880P2
COIL SPECIFICATIONS - DUAL COIL LATCHING ORDER NUMBER*
Nominal Must.Max. Continuous
Coil 1 Form A Coil Operate VDC
Resistance 1 Form A 2 Form A 1 Form B VDC VDC ± 10%
3
2.1 4.932.1 AZ880P2-1A-3D AZ880P2-2A-3D AZ880P2-1AB-3D
5 3.58.289.3 AZ880P2-1A-5D AZ880P2-2A-5D AZ880P2-1AB-5D
6 4.29.8129 AZ880P2-1A-6D AZ880P2-2A-6D AZ880P2-1AB-6D 9 6.314.7289 AZ880P2-1A-9D AZ880P2-2A-9D AZ880P2-1AB-9D 128.419.6514 AZ880P2-1A-12D AZ880P2-2A-12D AZ880P2-1AB-12D 24
16.8
39.3
2056 AZ880P2-1A-24D AZ880P2-2A-24D AZ880P2-1AB-24D
COIL SPECIFICATIONS - SINGLE COIL LATCHING ORDER NUMBER*
Nominal Must.Max. Continuous
Coil 1 Form A Coil Operate VDC
Resistance 1 Form A 2 Form A 1 Form B VDC VDC ± 10%
3
2.1 5.845 AZ880P1-1A-3D AZ880P1-2A-3D AZ880P1-1AB-3D
5 3.59.7125 AZ880P1-1A-5D AZ880P1-2A-5D AZ880P1-1AB-5D
6 4.211.6180 AZ880P1-1A-6D AZ880P1-2A-6D AZ880P1-1AB-6D 9 6.317.4405 AZ880P1-1A-9D AZ880P1-2A-9D AZ880P1-1AB-9D 128.423.2720 AZ880P1-1A-12D AZ880P1-2A-12D AZ880P1-1AB-12D 24
16.8
46.5
2880 AZ880P1-1A-24D AZ880P1-2A-24D AZ880P1-1AB-24D
*Add suffix “E” for epoxy sealed version. Add suffix “A” for gold plated contacts. Add suffix “R” for reversed polarity coil.
*Add suffix “E” for epoxy sealed version. Add suffix “A” for gold plated contacts. Add suffix “R” for reversed polarity coil.
Dimensions in inches with metric equivalents in parentheses. Tolerance: ± .010"