NF Authorization (Val
TAR Criteria for NF Authorization (Valdivia v. Coye) 1 As the result of a court order in Valdivia v. Coye issued in April 1993, Medi-Cal is required to approve Treatment Authorization Requests (TARs) for Medi-Cal covered therapy services when necessary for a Nursing Facility (NF) resident to attain or maintain the highest practicable physical, mental or psychosocial functioning in accordance with the comprehensive resident assessment and individualized plan of care.
This section specifies the TAR requirements for providers who render medical necessity services or to attain or maintain a patient’s plan of care. This section also describes the TAR requirements for exclusive services not covered under the long term care facility’s inclusive per diem rate. The “Inclusive and Exclusive Services Chart” and “Medical Necessity and Attain or Maintain Therapy Services Chart” at the end of this section illustrate specific therapy service examples when a request for additional authorization should be submitted.
Authorization Requirements Occupational, physical, speech and psychiatric therapy rendered to NF
Level A or B recipients require prior authorization. A TAR must be
submitted for services that are not part of the Medi-Cal inclusive per
diem rate for NFs.
Recipient Criteria The San Francisco Medi-Cal Field Office reviews therapy TARs for
Medi-Cal recipients who meet the following criteria:
?The recipient must reside in a NF Level A or B.
?The recipient must require therapy services by a trained and
licensed therapist.
?The therapy service(s) must be medically necessary and/or
necessary to attain or maintain the highest practicable
occupational, mental and psychosocial functioning.
The same recipient criteria applies to TARs submitted to the local
Medi-Cal field office for psychiatric therapy.
tar crit nf
2
TAR Criteria There are two standards of criteria for therapy TARs. Medi-Cal
recipients must meet one of the following criteria:
(1) California Code of Regulations (CCR), Section 51303
“Medical necessity limits health care services to those reasonable
and necessary to protect life, to prevent significant illness or
significant disability, or to alleviate severe pain through the
diagnosis or treatment of disease, illness or injury.”
If the therapy service does not meet the “medical necessity” regulatory
standard of criteria, the San Francisco Medi-Cal Field Office (or local
field office for psychiatric therapy requests) evaluates the TAR under
the following criteria:
(2) Valdivia Court Order and Stipulation, paragraph 2(f)(2)(ii).
“Each resident must receive, an d the facility must provide, the
necessary care and services to attain or maintain the highest
practicable physical, mental and psychosocial functioning, in
accordance with the comprehensive assessment and plan of
care.”
For specific therapy examples, re fer to the “Medical Necessity and
Attain or Maintain Therapy Services Chart” at the end of this
section.
tar crit nf
3 Inclusive and Exclusive In many cases, therapy services needed to attain and/or maintain the Services highest practicable level of functioning can and should be performed
as part of the Nursing Facility (NF) inclusive services rendered to the
Medi-Cal resident in the NF.
For examples illustrating the relationship between therapy services
that are covered in the inclusive services per diem rate and the
exclusive therapy services, refer to the “Inclusive and Exclusive
Services Chart” at the end of this section.
CCR, Title 22, Requirements: California Code of Regulations (CCR), Title 22, Sections 51510 and Sections 51510 and 51511 51511, state, with the exception of various services separately covered
by Medi-Cal, services rendered to NF residents pursuant to Federal
Medicaid laws and State licensing laws are reimbursed in the Medi-Cal
inclusive per diem rate.
tar crit nf
4
Sections 72315 and 73315 CCR, Title 22, Section 72315, lists requirements for nursing services
in a Nursing Facility providing NF Level B care. CCR, Title 22, Section
73315, lists the requirements for nursing services in a nursing facility
providing NF Level A care.
Note:Occupational, physical and speech therapy services are
included in the adult subacute care inclusive per diem rate.
However, therapy services are not included in the pediatric
subacute care inclusive per diem rate. These services must be
authorized on a 50-1 TAR and billed separately.
Psychiatric therapy services are not included in the adult and
pediatric subacute care inclusive per diem rate. These services
must be authorized on a 50-1 TAR and billed separately.
For examples of therapy services covered under the Medi-Cal per
diem rate, refer to the “Inclusive and Exclusive Services Chart” at the
end of this section.
Exclusive Services: Occupational, physical, speech and psychiatric therapy may be
TAR Required performed as part of the exclusive services and are payable separately
if a recipient needs licensed therapy intervention to meet his/her
specific medically necessary needs and/or to attain or maintain the
highest practicable level of functioning.
In these cases, providers must obtain an approved TAR for therapy
services with the express purpose of assessing the needs of the
recipient more thoroughly, providing direct therapy service(s), or
evaluating effectiveness of the planned treatment delivered by the NF staff.
For examples of services that may be authorized by completing a TAR,
refer to the “Inclusive and Exclusive Services Chart” at the end of this
section.
For a listing of subacute care inclusive and exclusive items, refer to
the Subacute Care Programs: Adult and Subacute Care Programs:
Pediatric sections in the appropriate Part 2 manual,and“TAR Criteria,”
on a previous page in this section. Additional information is also found
in the Per Diem Rates and Miscellaneous Inclusive and Exclusive
Items section in the Medi-Cal Long Term Care Provider Manual.
tar crit nf
5 Medical Transportation In most cases, the TAR-authorized therapy services can be provided
within the NF. However, where services are provided outside the
Nursing Facility, a TAR requesting non-emergency medical
transportation must be submitted to either the Sacramento or San
Diego Medi-Cal Field Office. Refer to the TAR Field Office Addresses
section in this manual to find out where to send non-emergency
medical transportation TARs for your area. The non-emergency
medical transportation TAR must include documentation that therapy
services have been requested.
Occupational, Physical,Providers must submit specific documentation when requesting prior Speech Therapy:authorization for recipients requiring either “medical necessity” or
TAR Documentation“attaining and maintaining” services.
Medical Necessity TAR If the Treatment Authorization Request (TAR) requesting therapy
services meets the Medi-Cal definition of “medical necessity,” the
following minimum documentation is needed:
?Minimum Data Set (MDS).
?Therapist’s plan of care.**
?Signed physician’s prescription/order. **
?The Patient Status box on the TAR (50-1) must include an “X” in
the SNF/ICF box if the patient is a resident of an NF.
Note: The TAR must clearly identify the Medi-Cal recipient for
whom services are requested as a “nursing facility
resident” to assure that requests for prior authorization of
the therapy services are evaluated consistently with the
Federal and State regulatory requirements for certified
nursing facilities.
tar crit nf
6
The Medical Justification area on the TAR (50-1) must indicate:
“Request is for a resident of (NURSING FACILITY NAME) nursing
facility.” Be sure to attach all documentation and supporting
medical information, the pertinent parts of the MDS, and the
recipient’s comprehensive care plan (including frequency of
services and probable length of treatment necessary to achieve
measurable goals) to the TAR.
Note: A recipient discharged from an acute hospital participating
in the Medi-Cal onsite Utilization Review directly to a
nursing facility may fall under the Discharge Planning
Option. For additional information, refer to the TAR
Discharge Planning Option sections in this manual.
**The signed physician’s order and the therapist evaluation may be
combined on a DHS form 6183 (Medical Justification for Therapy
Treatment Plan) and attached to the TAR.
tar crit nf
7 Attain and Maintain TAR If the TAR requesting therapy services does not meet the current
Medi-Cal definition of “medical necessity” and the Valdivia Court Order
and Stipulation is applied, the following documentation and supporting
medical justification must include at a minimum:
?All documentation and supporting medical information that would
normally accompany a TAR, including pertinent parts of the
Medi-Cal recipient’s Minimum Data Set (MDS).
Medi-Cal recipient’s Resident Assessment Protocol (RAP)
summary sheet is part of the Federal Resident Assessment
Instrument (RAI) that identifies the record location of various
information, including nature of the condition, complications and
risk factors, need for referrals to appropriate health professionals,
or reasons for decisions to proceed or not proceed.
?Medi-Cal recipient’s comprehensive plan of care.
?Signed physician’s prescription/orders. **
?Therapis t’s evaluation. **
?The Patient Status box on the Treatment Authorization Request
(TAR) (50-1) must include an “X” in the SNF/ICF box if the
patient is a resident of a Nursing Facility.
Note: The TAR must clearly identify the Medi-Cal recipient for
whom s ervices are requested as a “nursing facility
resident” to assure that requests for prior authorization of
the therapy services are evaluated consistently with the
Federal and State regulatory requirements for certified
nursing facilities.
?The Medical Justification area on the TAR (50-1) must indicate:
“Request is for a resident of (NURSING FACILITY NAME)
nursing facility.”
Note: If all of the “medical necessity” documentation and
Valdivia standard documentation previously listed are
submitted with the TAR, there will be less risk of TAR
deferrals and denials.
**The signed physician’s order and the therapist evaluation may be
combined on a DHS form 6183 (Medical Justification for Therapy
Treatment Plan) and attached to the TAR.
tar crit nf
8
Psychiatric Therapy:Psychiatric services may be requested for therapy rendered to
TAR Documentation Nursing Facility patients on an inpatient or outpatient basis.
Nursing Facility Additional authorization is required if acute psychiatric condition Patient Receiving Therapy services exceed the following limits:
on an Inpatient Basis
?Two hours per seven-day period during the first two months of
treatment
?One hour per seven-day period for the third through seventh
month of treatment
?One hour per 14-day period for each month after the seventh
month of treatment
?One hour per seven-day period during the month prior to
discharge
Nursing Facility In some instances, an NF patient cannot receive therapy services Patient Receiving Therapy within the Nursing Facility and the patient must be transported to the on an Outpatient Basis therapist. In these circumstances, prior authorization is required if the
services rendered on an outpatient basis exceed eight sessions in 120
days.
tar crit nf
9 Medical Necessity TAR If the TAR requesting therapy services meets the Medi-Cal definition of
“medical necessity,” the following minimum documentation is needed:
?Minimum Data Set (MDS).
?Therapist’s plan of care.
?Signed physician’s order if the psychiatrist is not the attending
physician.
?PASRR Level II determination that includes documentation that
the second level screen of the PASRR was completed, the facility
where the Medi-Cal recipient resides is the appropriate
placement for the Medi-Cal recipient, and documentation of the
need for mental health services.
?Documentation to substantiate the request for additional services.
?Claim showing the prior non-TAR authorized psychiatric visits
and/or hours billed to the Medi-Cal program.
?The Patient Status box on the Treatment Authorization Request
(50-1) must include an “X” in the SNF/ICF box if the patient is a
resident of a Nursing Facility.
Note: The TAR must clearly identify the Medi-Cal recipient for
whom services are requested as a “nursing facility
resident” to assure that requests for prior au thorization of
the therapy services are evaluated consistently with the
Federal and State regulatory requirements for certified
nursing facilities.
?The Medical Justification area on the Treatment Authorization
Request (50-1) must indicate: “Request is fo r a resident of
(NURSING FACILITY NAME) nursing facility.”
Attach all documentation and supporting medical information, the
pertinent parts of the MDS, and the recipient’s comprehensive care
plan (including frequency of services and probable length of treatment
necessary to achieve measurable goals) to the TAR.
tar crit nf
10
Attain and Maintain TAR If the TAR requesting therapy services does not meet the current
Medi-Cal definition of “medical necessity” and the Valdivia Court Order
and Stipulation is applied, the following documentation and supporting
medical justification must include at a minimum:
?All documentation and supporting medical information that would
normally accompany a TAR, including pertinent parts of the
Medi-Cal recipient’s Minimum Data Set (MDS).
Medi-Cal recipient’s Resident Assessment Protocol (RAP)
summary sheet as part of the Federal Resident Assessment
Instrument (RAI) that identifies the record location of various
information including, nature of the condition, complications and
risk factors, need for referrals to appropriate health professionals,
or reasons for decisions to proceed or not proceed.
?Medi-Cal recipient’s comprehensive plan of care.
?Statement describing the Medi-Cal recipient’s progress toward
achieving the therapeutic goals included in the Medi-Cal
recipient’s treatment plan.
?Signed physician’s order if the psychiatrist is not the attending
physician.
?Documentation to substantiate the additional TAR services and
therapy needed.
?Therapist’s evaluation.
?PASRR Level II determination that includes documentation that
the second level screen of the PASRR was completed, the facility
where the Medi-Cal recipient resides is the appropriate
placement for the Medi-Cal recipient, and documentation of the
need for mental health services.
? A claim showing the prior non-TAR authorized psychiatric visits
and/or hours billed to the Medi-Cal program.
tar crit nf
11
?The Patient Status box on the Treatment Authorization Request
(50-1) must include an “X” in the SNF/ICF box if the patient is a
resident of a Nursing Facility.
Note: The TAR must clearly identify the Medi-Cal recipient for
whom services are requested as a “nursing facility
resident” to assure that requests for prior authorization of
the therapy services are evaluated consistently with the
Federal and State regulatory requirements for certified
nursing facilities.
?The Medical Justification area on the Treatment Authorization
Request (50-1) must indicate: “Request is for a resident of
(NURSING FACILITY NAME) nursing facility.”
Note: If all of the “medical necessity” documentation and
Valdivia standard documentation previously listed are
submitted with the TAR, there will be less risk of TAR
deferrals and denials.
Reauthorization Requests To request reauthorization of psychiatric therapy services, the
psychiatrist must substantiate the need and include a statement
describing the recipient’s progress toward achieving the therapeutic
goals included in the recipient’s treatment plan. Outpatient
reauthorization must be received by the Medi-Cal field office prior to
the expiration of the previously authorized TAR.
tar crit nf
12
Key Questions:Individual differences of recipients need to be taken into account in When to Submit a TAR deciding whether a TAR is required for therapy services. Recipients
may respond to therapy differently depending on such factors as other
illnesses, complications and/or psychosocial needs. Key questions to
ask to determine when a TAR is required are included in the chart
below:
tar crit nf
13
Inclusive and Exclusive Services Chart
This chart illustrates the relationship between therapy services that are covered in the inclusive services per diem rate and the exclusive services rate. This chart is not meant to be an all inclusive list of when a TAR for additional therapy should be submitted, but lists a range of possibilities.
OCCUPATIONAL THERAPY SERVICES
PHYSICAL THERAPY SERVICES
tar crit nf
14
Inclusive and Exclusive Services Chart
SPEECH THERAPY SERVICES
PSYCHIATRIC THERAPY SERVICES
tar crit nf
15
Medical Necessity and Attain or Maintain Therapy Services Chart
Below is a chart illustrating therapy services needs that may be authorized on a TAR. This chart is not meant to be an all-inclusive list of when a TAR for additional therapy should be submitted, but lists a range of possibilities. This chart includes specific problems requiring therapy that would meet the current medical necessity criteria or the standard to attain or maintain.
螺纹通止规
螺纹通止规 定是:螺纹止规进入螺纹不能超过2.5圈,一般的要实际不得超过2圈,并且用得力度不能大,我们的经验是用拇指和食指轻轻夹持螺纹规以刚好能转动螺纹规的力度为准.力大了就相当于在使用丝锥或牙板了,那样规就用不了几次了. 螺纹通止规 螺纹通止规是适用于标准规定型号的灯头作为灯用附件电光源产品时候的设计和生产、检验的工具设备。 用途 一般用于检验螺纹灯头或灯座的尺寸是否符合标准要求，分别检验螺纹灯头的通规和止规尺寸或灯座的通规或止规尺寸。 工作原理 具体检验要求及介绍详见中国人民国国家标准：GB/T1483.1-2008或 IEC60061-3:2004标准规定容。 操作方法 具体检验要求及介绍详见中国人民国国家标准：GB/T1483.1-2008或 IEC60061-3:2004标准规定容。 通止规
通止规，是量规的一种。作为度量标准，用于大批量的检验产品。 通止规是量具的一种，在实际生产批量的产品若采取用计量量具（如游标卡尺，千分表等有刻度的量具）逐个测量很费事．我们知道合格的产品是有一个度量围的.在这个围的都合格，所以人们便采取通规和止规来测量． 通止规种类 （一）对统一英制螺纹，外螺纹有三种螺纹等级：1A、2A和3A级，螺纹有三种等级：1B、2B和3B级，全部都是间隙配合。等级数字越高，配合越紧。在英制螺纹中，偏差仅规定1A和2A级，3A级的偏差为零，而且1A和2A级的等级偏差是相等的等级数目越大公差越小，如图所示：1B 2B 3B 螺纹基本中径3A 外螺纹2A 1A 1、1A和1B级，非常松的公差等级，其适用于外螺纹的允差配合。 2、2A和2B级，是英制系列机械紧固件规定最通用的螺纹公差等级。 3、3A和3B级，旋合形成最紧的配合，适用于公差紧的紧固件，用于安全性的关键设计。 4、对外螺纹来说，1A和2A级有一个配合公差，3A级没有。1A级公差比2A级公差大50，比3A级大75，对螺纹来说，2B级公差比2A公差大30。1B级比2B级大50，比3B级大75。 （二）公制螺纹，外螺纹有三种螺纹等级：4h、6h和6g，螺纹有三种螺纹等级：5H、6 H、7H。（日标螺纹精度等级分为I、II、III三级，通常状况下为II级）在公制螺纹中，H 和h的基本偏差为零。G的基本偏差为正值，e、f和g的基本偏差为负值。如图所示：公差G H 螺纹偏差基本中径外螺纹f g h e 1、H是螺纹常用的公差带位置，一般不用作表面镀层，或用极薄的磷化层。G位置基本偏差用于特殊场合，如较厚的镀层，一般很少用。 2、g常用来镀6-9um的薄镀层，如产品图纸要6h的螺栓，其镀前螺纹采用6g的公差带。 3、螺纹配合最好组合成H/g、H/h或G/h，对于螺栓、螺母等精制紧固件螺纹，标准推荐采用6H/6g的配合。 （三）螺纹标记M10×1–5g 6g M10×1–6H 顶径公差代号中径和顶径公差代号（相同）中径公差代号。 通止规是两个量具分为通规和止规．举个例子：M6－7h的螺纹通止规一头为通规（T）如果能顺利旋进被测螺纹孔则为合格，反之不合格需返工（也就是孔小了）．然后用止规（Z）如果能顺利旋进被测螺纹孔2.5圈或以上则为不合格反之合格．且此时不合格的螺纹孔应报废，不能进行返工了．其中2.5圈为国家标准，若是出口件最多只能进1.5圈（国际标准）．总之通规过止规不过为合格，通规止规都不过或通规止规都过则为不合格。
英文财务指标及计算公式汇总
Ratios Profitability ratios Profitability ratios measure the firm's use of its assets and control of its expenses to generate an acceptable rate of return. Gross margin, Gross profit margin or Gross Profit Rate OR Operating margin, Operating Income Margin, Operating profit margin or Return on sales (ROS) Note: Operating income is the difference between operating revenues and operating expenses, but it is also sometimes used as a synonym for EBIT and operating profit.[10] This is true if the firm has no non-operating income. (Earnings before interest and taxes / Sales) Profit margin, net margin or net profit margin Return on equity (ROE) Return on investment (ROI ratio or Du Pont ratio) Return on assets (ROA) Return on assets Du Pont (ROA Du Pont)
螺纹通止规要求螺纹通规通
螺纹通止规要求螺纹通规通，止规止。 但是如果螺纹通规止，说明什么？ 螺纹止规通，又说明什么？ 我也来说两句查看全部回复 最新回复 ?wpc (2008-11-07 20:11:20) 在牙型正确的前提下螺纹通止规检测螺纹中径 ?lobont (2008-11-08 11:16:32) 对外螺纹而言，螺纹通规是做到中径上偏差，所以能通过就表示产品合格，通不过就表示螺纹做大了，要再修一刀； 螺纹止规做到中径下偏差，所以只能通过2～3牙，如果也通过，就表示外螺纹做小了，产品成为废品 ?qubin8512 (2008-11-18 15:36:05) 螺纹赛规与螺纹环规主要测量螺纹的中径。 ?datafield (2008-11-29 19:12:51) 检具不是万能的，只是方便而已。具体没什么的我有在哪本书上看过，是一本螺纹手册上的。 ?ZYC007 (2009-2-09 20:31:13) 在牙型正确的前提下螺纹通止规检测螺纹中径。 对外螺纹而言，但是如果螺纹通规止，说明螺纹中径大；螺纹止规通，又说明螺纹中径小。 ?WWCCJJ (2009-3-19 09:27:19) 检测的是螺纹的中径,螺纹检测规在检定时,也是检测其中径. ?tanjiren (2009-3-20 22:23:06) 螺纹通止规只能检测螺纹的作用中径,大径和底径等均无法准确测量出来. ?月夜(2009-4-01 21:47:13) 用来测量中径 ?丽萍(2009-4-02 10:11:41)
只能检测工件螺纹的中径 yg196733456 (2009-4-03 09:15:56)原来是测中径的知道了
常见财务指标中英文简写
常见财务指标中英文简写 GAAP ?Generally?Accepted?Accounting?Principle?公认会计准则 CEO? Chief?Executive?Office?首席执行官 IASC International?Accounting?Standard?Committee国际会计准则委员会CPA Certificated?Public?Accountant注册会计师 WCR Working?Capital?Requirement营运资本需求量 ROE Return?on?Equity权益资本收益率（净资产收益率） ROIC Return?on?Investment?Capital投入资本收益率? EPS Earning?Per?Share每股净利润（每股收益） DPS Dividend?Per?Share?每股股利 P/E Price?-?Earning?Ratio市盈率 BVEPS Book?Value?of?Equity?Per?Share每股净资产（每股权益资本）EVA Economic?Value?Added经济增加值（经济利润） MVA Market?Value?Added市场增加值 EBT Earning?Before?Tax?税前利润 EBIT Earning?Before?Interest?And?Tax息税前利润 EAT Earning?After?Tax税后利润 ROA Return?on?Asset?资产收益率 DOL Degree?of?Operating?Leverage经营风险或经营杠杆程度 DFL Degree?of?Financial?Leverage?财务风险或财务杠杆程度 DTL Degree?of?Total?Leverage总风险或总杠杆 WACC Weighted?Average?Cost?of?Capital加权平均资本成本 TS Total?Sales销售收入? TC Total?Cost总成本 VC? Variable?Cost单位变动成本 TFC ?Total?Fixed?Cost?总固定成本 NPV Net?Present?Value净现值 IRR ?Internal?Rate?of?Return?内含报酬率 PBP Pay-back?Period回收期 BEP Break?Even?Point保本点 NWC Net?Working?Capital净营运资金 NCF Net?Cash?Flows现金净流量 DCPBP Discounted?Cash-flow?Pay-back?Period?折现累计回收期 BOPBP Bailout?Pay-back?Period脱险回收期 Net P Net profit 净利润
NPT螺纹以及检测方法详解
N P T螺纹以及检测方法详 解 Prepared on 22 November 2020
一、目的：规范公司技术员，检验员，操作员对NPT螺纹的了解。 二、适用范围：适用于公司任何NPT螺纹类产品，参考资料为通用管螺 纹和国家标准GB/T12716-2011。 三、目录 1、NPT和NPTF介绍 2、螺纹技术参数参数讲解 3、NPT与NPTF加工工艺 4、NPT和NPTF的检测方法 四、内容： NPT和NPTF螺纹介绍 NPT 是 National (American) Pipe Thread 的缩写，属於美国标准的 60 度锥管 密封螺纹，用於北美地区，美国标准为13)通用管螺纹．国家标准可查阅 GB/T12716-2011。NPTF：美制干密封圆锥管螺。NPTF = National Pipe Thread Fine 称之为一般用途的锥管螺纹，这也是我们以前称之为的布氏锥螺纹。NPTF 螺纹称之为干密封式锥管螺纹，它连接密封的原理是在没有润滑剂或密封填 料情况下完全依靠螺纹自身形成密封，设计意图是使内、外螺纹牙的侧面、 牙顶和牙底同时接触，来达到密封的目的。它们两者的牙型角、斜度等指标 都是相同的，关键是牙顶和牙底的削平高度不一样，所以，量规的设计也是 不一样的。NPTF干密封管螺纹的牙形精度比NPT螺纹高，旋合时不用任何 填料，完全依靠螺纹自身形成密封，螺纹间无任何密封介质。干密封管螺纹 规定有较为严格的公差，属精密型螺纹，仅用在特殊场合。这种螺纹有较高 的强度和良好的密封性，在具有薄截面的脆硬材料上采用此螺纹可以减少断 裂现象。NPTF内、外螺纹牙顶与牙底间没有间隙，是过盈配合，而NPT螺 纹是过渡配合。NPTF螺纹主要用于高温高压对密封要求严格的场所。NPT
财务报表中英文对照
财务报表中英文对照 1.资产负债表Balance Sheet 项目ITEM 货币资金Cash 短期投资Short term investments 应收票据Notes receivable 应收股利Dividend receivable 应收利息Interest receivable 应收帐款Accounts receivable 其他应收款Other receivables 预付帐款Accounts prepaid 期货保证金Future guarantee 应收补贴款Allowance receivable 应收出口退税Export drawback receivable 存货Inventories 其中：原材料Including:Raw materials 产成品(库存商品) Finished goods 待摊费用Prepaid and deferred expenses 待处理流动资产净损失Unsettled G/L on current assets 一年内到期的长期债权投资Long-term debenture investment falling due in a year 其他流动资产Other current assets 流动资产合计Total current assets 长期投资：Long-term investment： 其中:长期股权投资Including long term equity investment 长期债权投资Long term securities investment *合并价差Incorporating price difference 长期投资合计Total long-term investment 固定资产原价Fixed assets-cost 减：累计折旧Less:Accumulated Dpreciation 固定资产净值Fixed assets-net value 减：固定资产减值准备Less:Impairment of fixed assets 固定资产净额Net value of fixed assets 固定资产清理Disposal of fixed assets 工程物资Project material 在建工程Construction in Progress 待处理固定资产净损失Unsettled G/L on fixed assets 固定资产合计Total tangible assets 无形资产Intangible assets
通止规的用法及管理
通止规的用法及管理 1、止规 使用前：应经相关检验计量机构检验计量合格后，方可投入生产现场使用。 使用时：应注意被测螺纹公差等级及偏差代号与环规标识公差等级、偏差代号相同（如M24*1.5-6h与M24*1.5-5g两种环规外形相同，其螺纹公差带不相同，错用后将产生批量不合格品)。 检验测量过程：首先要清理干净被测螺纹油污及杂质，然后在环规与被测螺纹对正后，用大母指与食指转动环规，旋入螺纹长度在2个螺距之内为合格，否则判为不合格品。 2、通规 使用前：应经相关检验计量机构检验计量合格后，方可投入生产现场使用。 使用时：应注意被测螺纹公差等级及偏差代号与环规标识的公差等级、偏差代号相同（如M24*1.5-6h与M24*1.5-5g两种环规外形相同，其螺纹公差带不相同，错用后将产生批量不合格品)。 检验测量过程：首先要清理干净被测螺纹塞规油污及杂质，然后在环规与被测螺纹对正后，用大母指与食指转动环规，使其在自由状态下旋合通过螺纹全部长度判定合格，否则以不通判定。 3、注意事项 在用量具应在每个工作日用校对塞规计量一次。经校对塞规计量超差或者达到计量器具周检期限的环规，由计量管理人员收回、标识隔离并作相应的处理措施。 可调节螺纹环规经调整后，测量部位会产生失圆，此现象由计量修复人员经螺纹磨削加工后再次计量鉴定，各尺寸合格后方可投入使用。 报废环规应标识隔离并及时处理，不得流入生产现场。 4、维护与保养 量具（环规）使用完毕后，应及时清理干净测量部位附着物，存放在规定的量具盒内。生产现场在用量具应摆放在工艺定置位置，轻拿轻放，以防止磕碰而损坏测量表面。 严禁将量具作为切削工具强制旋入螺纹，避免造成早期磨损。可调节螺纹环规严禁非计量工作人员随意调整，确保量具的准确性。环规长时间不用，应交计量管理部门妥善保管。
通止规的用法及管理
通止规的用法及管理 令狐采学 1、止规 使用前：应经相关检验计量机构检验计量合格后，方可投入生产现场使用。 使用时：应注意被测螺纹公差等级及偏差代号与环规标识公差等级、偏差代号相同（如M24*1.56h与M24*1.55g两种环规外形相同，其螺纹公差带不相同，错用后将产生批量不合格品)。 检验测量过程：首先要清理干净被测螺纹油污及杂质，然后在环规与被测螺纹对正后，用大母指与食指转动环规，旋入螺纹长度在2个螺距之内为合格，否则判为不合格品。 2、通规 使用前：应经相关检验计量机构检验计量合格后，方可投入生
产现场使用。 使用时：应注意被测螺纹公差等级及偏差代号与环规标识的公差等级、偏差代号相同（如M24*1.56h与M24*1.55g两种环规外形相同，其螺纹公差带不相同，错用后将产生批量不合格品)。 检验测量过程：首先要清理干净被测螺纹塞规油污及杂质，然后在环规与被测螺纹对正后，用大母指与食指转动环规，使其在自由状态下旋合通过螺纹全部长度判定合格，否则以不通判定。 3、注意事项 在用量具应在每个工作日用校对塞规计量一次。经校对塞规计量超差或者达到计量器具周检期限的环规，由计量管理人员收回、标识隔离并作相应的处理措施。 可调节螺纹环规经调整后，测量部位会产生失圆，此现象由计量修复人员经螺纹磨削加工后再次计量鉴定，各尺寸合格后方
可投入使用。 报废环规应标识隔离并及时处理，不得流入生产现场。 4、维护与保养 量具（环规）使用完毕后，应及时清理干净测量部位附着物，存放在规定的量具盒内。生产现场在用量具应摆放在工艺定置位置，轻拿轻放，以防止磕碰而损坏测量表面。 严禁将量具作为切削工具强制旋入螺纹，避免造成早期磨损。可调节螺纹环规严禁非计量工作人员随意调整，确保量具的准确性。环规长时间不用，应交计量管理部门妥善保管。
常见财务指标中英文简写
常见财务指标中英文简 写 SANY GROUP system office room 【SANYUA16H-
常见财务指标中英文简写 GAAP ?Generally?Accepted?Accounting?Principle?公认会计准则 CEO? Chief?Executive?Office?首席执行官 IASC International?Accounting?Standard?Committee国际会计准则委员会CPA Certificated?Public?Accountant注册会计师 WCR Working?Capital?Requirement营运资本需求量 ROE Return?on?Equity权益资本收益率（净资产收益率） ROIC Return?on?Investment?Capital投入资本收益率? EPS Earning?Per?Share每股净利润（每股收益） DPS Dividend?Per?Share?每股股利 P/E Price?-?Earning?Ratio市盈率 BVEPS Book?Value?of?Equity?Per?Share每股净资产（每股权益资本）EVA Economic?Value?Added经济增加值（经济利润） MVA Market?Value?Added市场增加值 EBT Earning?Before?Tax?税前利润 EBIT Earning?Before?Interest?And?Tax息税前利润 EAT Earning?After?Tax税后利润 ROA Return?on?Asset?资产收益率 DOL Degree?of?Operating?Leverage经营风险或经营杠杆程度 DFL Degree?of?Financial?Leverage?财务风险或财务杠杆程度 DTL Degree?of?Total?Leverage总风险或总杠杆 WACC Weighted?Average?Cost?of?Capital加权平均资本成本 TS Total?Sales销售收入? TC Total?Cost总成本 VC? Variable?Cost单位变动成本 TFC ?Total?Fixed?Cost?总固定成本 NPV Net?Present?Value净现值 IRR ?Internal?Rate?of?Return?内含报酬率 PBP Pay-back?Period回收期 BEP Break?Even?Point保本点 NWC Net?Working?Capital净营运资金 NCF Net?Cash?Flows现金净流量 DCPBP Discounted?Cash-flow?Pay-back?Period?折现累计回收期BOPBP Bailout?Pay-back?Period脱险回收期 Net P Net profit 净利润
通止规的用法及管理修订稿
通止规的用法及管理 WEIHUA system office room 【WEIHUA 16H-WEIHUA WEIHUA8Q8-
通止规的用法及管理 1、止规 使用前：应经相关检验计量机构检验计量合格后，方可投入生产现场使用。 使用时：应注意被测螺纹公差等级及偏差代号与环规标识公差等级、偏差代号相同（如M24*与M24*两种环规外形相同，其螺纹公差带不相同，错用后将产生批量不合格品)。 检验测量过程：首先要清理干净被测螺纹油污及杂质，然后在环规与被测螺纹对正后，用大母指与食指转动环规，旋入螺纹长度在2个螺距之内为合格，否则判为不合格品。 2、通规 使用前：应经相关检验计量机构检验计量合格后，方可投入生产现场使用。 使用时：应注意被测螺纹公差等级及偏差代号与环规标识的公差等级、偏差代号相同（如M24*与M24*两种环规外形相同，其螺纹公差带不相同，错用后将产生批量不合格品)。 检验测量过程：首先要清理干净被测螺纹塞规油污及杂质，然后在环规与被测螺纹对正后，用大母指与食指转动环规，使其在自由状态下旋合通过螺纹全部长度判定合格，否则以不通判定。 3、注意事项
在用量具应在每个工作日用校对塞规计量一次。经校对塞规计量超差或者达到计量器具周检期限的环规，由计量管理人员收回、标识隔离并作相应的处理措施。 可调节螺纹环规经调整后，测量部位会产生失圆，此现象由计量修复人员经螺纹磨削加工后再次计量鉴定，各尺寸合格后方可投入使用。 报废环规应标识隔离并及时处理，不得流入生产现场。 4、维护与保养 量具（环规）使用完毕后，应及时清理干净测量部位附着物，存放在规定的量具盒内。生产现场在用量具应摆放在工艺定置位置，轻拿轻放，以防止磕碰而损坏测量表面。 严禁将量具作为切削工具强制旋入螺纹，避免造成早期磨损。可调节螺纹环规严禁非计量工作人员随意调整，确保量具的准确性。环规长时间不用，应交计量管理部门妥善保管。
财务报表各项目中英文对照
财务报表各项目中英文对照 一、损益表INCOME STATEMENT Aggregate income statement 合并损益表 Operating Results 经营业绩 FINANCIAL HIGHLIGHTS 财务摘要 Gross revenues 总收入/毛收入 Net revenues 销售收入/净收入 Sales 销售额 Turnover 营业额 Cost of revenues 销售成本 Gross profit 毛利润 Gross margin 毛利率 Other income and gain 其他收入及利得 EBITDA 息、税、折旧、摊销前利润（EBITDA） EBITDA margin EBITDA率 EBITA 息、税、摊销前利润 EBIT 息税前利润/营业利润 Operating income（loss）营业利润/（亏损） Operating profit 营业利润 Operating margin 营业利润率 EBIT margin EBIT率（营业利润率） Profit before disposal of investments 出售投资前利润 Operating expenses: 营业费用： Research and development costs （R&D）研发费用 marketing expenses Selling expenses 销售费用 Cost of revenues 营业成本 Selling Cost 销售成本 Sales and marketing expenses Selling and marketing expenses 销售费用、或销售及市场推广费用 Selling and distribution costs 营销费用/行销费用 General and administrative expenses 管理费用/一般及管理费用 Administrative expenses 管理费用 Operating income（loss）营业利润/（亏损） Profit from operating activities 营业利润/经营活动之利润 Finance costs 财务费用/财务成本 Financial result 财务费用 Finance income 财务收益 Change in fair value of derivative liability associated with Series B convertible redeemable preference shares 可转换可赎回优先股B相关衍生负债公允值变动 Loss on the derivative component of convertible bonds 可換股債券衍生工具之損失 Equity loss of affiliates 子公司权益损失 Government grant income 政府补助 Other (expense) / income 其他收入/（费用）
螺纹规使用方法
螺纹规使用方法 一、目的 规范塞规、环规使用的操作方法，保证测量结果的准确性。螺纹塞规使用者应根据操作规范要求，确保操作过程正确，并负责仪器的维护和保养。 二、说明 螺纹规又称螺纹通止规、螺纹量规，通常用来检验判定螺纹的尺寸是否合格。 螺纹规根据所检验内外螺纹分为螺纹塞规和螺纹环规，目前我们所使用的只有螺纹塞规。 图1 三、使用方法 1、选择螺纹规时，应选择与被测螺纹相匹配的规格。 2、使用前，先清理干净螺纹规和被测螺纹表面的油污、杂质等。 3、使用时，使螺纹规的通端（止端）与被测螺纹对正后，用大拇指与食指转动螺纹规或被 测零件，使其在自由状态下旋转。通常情况下（无被测零件的螺纹的图示说明时），螺纹 规（通端）的通规可以在被测螺纹的任意位置转动,通过全部螺纹长度则判定为合格，否 则为不合格品;在螺纹规（止端）的止规与被测螺纹对正后，旋入螺纹长度在2个螺距之 内止住为合格，不可强行用力通过，否则判为不合格品。（有被测零件的图示说明时，应 按照图示说明做判定。） 图2 图3 图中英文字母“GO”或“T”:表 示螺纹塞规的通端。 图中“G 3/8-19”或“M3 6H” 表示该螺纹规规格. 图中英文字母“NO GO”或“Z”: 表示螺纹塞规的止端。 螺纹塞规
4、检验工件时旋转螺纹规不能用力拧，用三只手指自然顺畅地旋转，止住即可，螺纹规退 出工件最后一圈时也要自然退出，不能用力拔出螺纹规,否则会影响产品检验结果的误差,螺纹规的损坏。 图4 图5 如上图4操作方法是正确的，图5是错误的，无需手握。 5、使用完毕后，及时清理干净螺纹规的通端（止端）的表面附着物，并存放在工具柜的量 具盒内。 四、注意事项 1、被测件螺纹公差等级及偏差代号必须与塞规标识公差等级、偏差代号相同，才可使用。 2、只有当通规和止规联合使用，并分别检验合格，才表示被测螺纹合格。 3、应避免与坚硬物品相互碰撞，轻拿轻放，以防止磕碰而损坏测量表面。 4、严禁将螺纹规作为切削工具强制旋入螺纹，避免造成早期磨损。 5、螺纹规使用完毕后，应及时清理干净测量部位附着物，存放在规定的量具盒内。 五、维护和保养 1、每月定期涂抹防锈油，以保证表面无锈蚀、无杂质（我们的螺纹规使用频繁且所 处环境干净无需上油保护）。 2、所有的螺纹规必须经计量校验机构校验合格后并在校验有效期内，方可使用。 3、损坏或报废的螺纹规应及时反馈处理，不得继续使用。 4、经校对的螺纹规计量超差或者达到计量器具周检期的螺纹规，由计量管理人员收回 并做相应的处理。
中英文对照版财务报表
一、企业财务会计报表封面 FINANCIAL REPORT COVER 报表所属期间之期末时间点 Period Ended 所属月份 Reporting Period 报出日期 Submit Date 记账本位币币种 Local Reporting Currency 审核人 Verifier 填表人 Preparer 二、资产负债表 Balance Sheet 资产 Assets 流动资产 Current Assets 货币资金 Bank and Cash 短期投资 Current Investment 一年内到期委托贷款 Entrusted loan receivable due within one year 减：一年内到期委托贷款减值准备 Less: Impairment for Entrusted loan receivable due within one year 减：短期投资跌价准备 Less: Impairment for current investment 短期投资净额 Net bal of current investment 应收票据 Notes receivable 应收股利 Dividend receivable 应收利息 Interest receivable 应收账款 Account receivable 减：应收账款坏账准备 Less: Bad debt provision for Account receivable 应收账款净额 Net bal of Account receivable 其他应收款 Other receivable 减：其他应收款坏账准备 Less: Bad debt provision for Other receivable 其他应收款净额 Net bal of Other receivable 预付账款 Prepayment 应收补贴款 Subsidy receivable 存货 Inventory 减：存货跌价准备 Less: Provision for Inventory 存货净额 Net bal of Inventory 已完工尚未结算款 Amount due from customer for contract work 待摊费用 Deferred Expense 一年内到期的长期债权投资 Long-term debt investment due within one year 一年内到期的应收融资租赁款 Finance lease receivables due within one year 其他流动资产 Other current assets 流动资产合计 Total current assets 长期投资 Long-term investment 长期股权投资 Long-term equity investment 委托贷款 Entrusted loan receivable 长期债权投资 Long-term debt investment
HGS型钢筋直螺纹滚丝机使用说明书
H G S型钢筋直螺纹滚丝 机使用说明书 集团标准化办公室：[VV986T-J682P28-JP266L8-68PNN]
HGS-40型钢筋直螺纹滚丝机使用说明书 一．用途 HGS-40型钢筋直螺纹滚丝机。主要用于建筑工程带肋钢滚轧直螺纹丝头，是实现钢筋连接的关键设备。可加工直径16-40mm的HRB335和HRB400级带肋钢筋。 二．特点 HGS-40型钢筋直螺纹滚丝机，可一次装夹完成从剥肋到滚轧螺纹的加工过程。加工螺纹的牙形饱满，尺寸精度高，机械强度高。 既可加工正扣螺纹，也可加工反扣螺纹。 本机操作简单、结构紧凑、工作可靠，具有独特的刀具自动开合机构。 可加工直径范围为16－40mm的HRB335和HRB400级钢筋。 三．结构 HGS－40型钢筋直螺纹滚丝机，由机架、夹紧钳、导轨、滑板、摆线针轮减速机、剥肋滚轧头、进给机构、自动开合机构、行程限位机构、冷却系统、电器控制箱、控制系统等部分组成。
四．主要技术参数 1．加工钢筋直径范围：φ16-φ40mm 2．主电机功率： KW 3．配用电源：三相380V 50Hz 4．主轴转速：40-62r／min 5．最大加工长度：80mm 6．重量：560kg 五．使用方法 （一）加工前的准备 1．按要求接好电源线和接地线，接通电源。电源为三相380V 50Hz的交流电源，为保证人身安全请使用带漏电保护功能的自动开关。 2．冷却液箱中，加足溶性冷却液(严禁加油性冷却液）。
（二）空车试转 1．接通电源。检查冷却水泵工作是否正常。 2．操作按钮，检查电器控制系统工作是否正常。 （三）加工前的调整 1．根据所加工钢筋的直径，调换与加工直径相适应的滚丝轮。滚丝轮与加工钢筋直径的关系见表一： 2．调换滚丝轮的同时，调换与滚丝轮螺距相适宜的垫圈，以保证螺距的正确性，螺距与垫圈厚度的关系见表二： 3．滚丝轮与加工直径相适应后，将与钢筋相适应的对刀棒插入滚轧头中心，调整滚丝轮使之与对刀棒相接触，抽出对刀棒，拧紧螺钉，压紧齿圈，使之不得移动。 4．对于固定定位盘的设备根据所加工钢筋直径，调换与加工直径相适应的定位盘（定位盘上打印有加工直径）。对于可调整定位盘的设备按定位盘刻度调整到相应的刻度，当剥肋刀磨损时还需要进行微调。 5．根据所加工钢筋规格，调整剥肋行程档块的位置，保证剥肋长度达到要求值。剥肋长度与钢筋规格的关系见表三：
螺纹环规(通规止规)的使用方法
一、螺纹环规是一种“量具”，是用来检测标准外螺纹中径的，两个为一套，一个通规，一个止 规。两个环规的内螺纹中径分别按照标准螺纹中径的最大极限尺寸和最小极限尺寸制造的，精度非常高。 二、使用方法 1、通规使用前： 应经相关检验计量机构检验计量合格后，方可投入生产现场使用。 使用时：应注意被测螺纹公差 等级及偏差代号与环规标识的公差等级、偏差代号相同（如M24 ×1.5 6h 与M24×1.5 5g 两种环 规外形相同,其螺纹公差带不相同,错用后将产生批量不合格品)。 检验测量过程： 首先要清理干净被测件螺纹油污及杂质，然后在环规与被测件螺纹对正后， 用大拇指与食指转动环规，使其在自由状态下旋合通过螺纹全部长度判定合格，否则以不通判定。 2、止规使用前： 应经相关检验计量机构检验计量合格后，方可投入生产现场使用。 使用时： 应注意被测件螺纹公差等级及偏差代号与环规标识公差等级、偏差代号相同。 检验测量过程： 首先要清理干净被测螺纹油污及杂质，然后在环规与被测螺纹对正后，用大拇指与食指转动环规，旋入螺纹长度在2个螺距之内后止住为合格，否则判为不合格品。 3、通规可以在螺纹的任意位置转动自如，止规拧一至两三圈，（可能有时还能多拧一两圈，但螺纹头部没出环规端面）就拧不动了，这时说明你检测的外螺纹中径正好在“公差带”内，是合格的产品。 4、只有当通规和止规联合使用，并分别检验合格，才表示被测工件合格。 三、维护和保养 螺纹环规使用完毕后，应及时清理干净测量部位附着物，存放在规定的量具盒内。环规使用时应轻拿轻放，环规严禁套在坚硬物品上面旋转。严禁将环规强制旋入螺纹，避免造成早期磨损，确保环规的准确性。长时间不使用，应涂上防锈油。 图中英文字母“T”:表示螺纹环规的通规。 图中英文字母“Z”:表示螺纹环规的止规。 图中“MJ10×1.5 6g”及“7/8-6ACME”表示该螺纹环规的规格。 使用螺纹环规口诀： 通规通；止规止！
HK通用检测标准
钣金件检验规范 1 目的 为了确保钣金件类物料的质量符合公司所规定的要求 2 适用范围 本规范适用于本公司无特殊要求的钣金件来料检验。 3 检验依据、抽样方案以及质量合格水平 3.1依据：（1）图纸；（2）封样；（3）器件认定资料； 3.2 对每批次进货的钣金件 (每次进货为一个批次)，按GB/T 2828.1-2003?中一般检查水平的一次抽样方案和定数抽样方案进行抽检, 所有定数检验项目, 检验合格的判定依据Ac/Re 为0/1判据：即发现1个不合格即判该批为不合格,检验内容详见下表。 3.3 缺陷等级定义：A表示严重缺陷 B表示重缺陷 C轻缺陷 4 职责 ? 主管部门为品质管理部，配合部门为研发中心、供应部及生产部。 5 检测仪器、工具及检测条件 ? 5.1检测仪器、工具 游标卡尺、塞规、螺纹通止规、色差计、3M600胶带、2H中华铅笔、橡皮擦、铅笔硬度计、百格刀、无水酒精、高度计、影像测量仪、三坐标测量机及一些检验工装； 5.2检测条件 样品表面（观察面）与照明平行，视线呈45度进行观察，被检验产品在荧光灯下1.2米处，眼睛距物30厘米观察3-5秒，视力或矫正视力应不低于1.0，检验时不能使用放大镜。 6 检验标准 6.1判定总则： 1）可接收的等级面缺陷不能影响产品的装配和功能，否则仍判不合格。 2）有封样或图纸上有特殊要求的零件，其对应的缺陷优先按其限度样板或技术要求的标准进行判断。 3）对某一缺陷判定有歧异，或者出现本规范中未定义的缺陷时，由SQE工程师进行仲裁判定并签订限度样品。 4）同一表面缺陷不能聚集过多，实际缺陷数量不能超过缺陷允收表规定的缺陷数 N 。 5）同一表面同一区域缺陷不能聚集过大，即以规定缺陷间距为半径的圆周内，实际测量结果不能大于缺陷允收表的要求。对于可累积计算的缺陷如长度L和面积S等，记录累积值（L ＝L1+L2+…Ln，S＝S1+S2+…Sn）与缺陷允收表比较。对无法累积计算的缺陷如高度H，宽度W，直径D等，记录最大的测量值与缺陷允收表比较。
施必牢防松螺母使用指南
上海底特精密紧固件有限公司 第 1 页 共 1 页 2010-12-24 施必牢? 防松螺母设计和使用指南 ◆ 施必牢防松螺母只适用于刚性连接，不适用于柔性连接，见右图。 ◆ 施必牢防松螺母是有方向性的，只有按正确方向旋入紧固才具有 防松效果，见右下图。为了辨别方向，常规的施必牢螺母外形只 有两种：凸缘和法兰面外形。一般情况下建议不要使用六角螺母。 ◆ 安装扭矩 ◇ 安装力矩是根据配用螺栓的性能等级和螺母的表面处理确定的。 不同的表面处理安装力矩不同。常用表面处理的安装力矩见 《施必牢螺母常用表面处理安装力矩表》。 ◇ 对特定的应用，我们将给出专用的安装扭矩。 ◆ 装配工具 ◇ 电动或液压定扭矩扳手 ◇ 力矩扳手 ◇ 气动或电动扳手预装，然后用力矩扳手紧固至规定的力矩 ◆ 螺栓螺母性能等级应匹配。性能高的螺母可替代性能低的螺母。 螺栓、螺母性能等级匹配 螺栓性能等级 5.8 8.8 10.9 12.9 螺母性能等级 5 8 10 12
◆ 配套螺栓：螺栓外螺纹精度等级：镀（涂）前6g （注：许多制造厂对螺纹的检查仅限于螺纹通止规，这是不完全的。因为，螺纹通止环规仅检查了螺纹作用中径，不能对螺纹大径进行检查。螺纹大径的检查需用外径千分尺或游标卡尺进行） ◆使用施必牢螺母后，可不需弹簧垫圈、锁片和其它防松零件（形式）。如果需用平垫圈时，请使用硬度级别为300HV的平垫圈。 ◆ 施必牢螺母的防松性能来源于其楔形结构的螺纹。只要螺纹合格，螺母就具有防松性能。由于施必牢螺纹结构特殊，因此，施必 牢螺纹的检测必须使用专用的施必牢螺纹塞规。施必牢螺纹塞规为三件一套：一支通规、一支斜面止规、一支中径止规。施必牢螺纹塞规旋入被测螺母的方向与螺栓旋入螺母的方向现同。其使用规则见下表。 螺纹量规名称外形特征使用规则 螺纹通规螺纹牙顶尖a、应与工件内螺纹旋合通过；* b、如果量规可以通过，但有一定的阻滞，亦为合格。 螺纹斜面止规螺纹牙顶尖允许与工件那螺纹旋合，但旋合量应不超过三扣螺纹。 螺纹中径止规螺纹牙顶较平a、与工件内螺纹旋合不能通过； b、在有一定阻滞的情况下，止规完全通过亦为合格。但感受到阻 滞应在第三牙之前。 * 表面有镀（涂）层的产品如果螺纹通规不通，去除镀（涂）层后螺纹通规通亦为合格。 ◆零件基体上攻制施必牢螺孔时，底孔应符合推荐的底孔直径。底孔直径和施必牢丝锥外形尺寸见《施必牢螺纹标准丝锥》。 上海底特精密紧固件有限公司第 2 页共 2 页 2010-12-24
财务报表中英文
新会计准则下的英文版的会计报表 一、企业财务会计报表封面 FINANCIAL REPORT COVER 报表所属期间之期末时间点 Period Ended 所属月份Reporting Period 报出日期Submit Date 记账本位币币种Local Reporting Currency 审核人Verifier 填表人Preparer 二、资产负债表Balance Sheet 资产Assets 流动资产Current Assets 货币资金Cash and Cash Equivalents 短期投资Short-term Investment 一年内到期委托贷款Entrusted Loan Receivable Due within One Year 减：一年内到期委托贷款减值准备 Deduct: Depreciation Reserve for Entrusted Loan Receivable Due within One Year 减：短期投资跌价准备Deduct: Falling Price Reserve for Short-term Investment 短期投资净额Net Value of Short-term Investment 应收票据Notes Receivable 应收股利Dividends Receivable 应收利息Interest Receivable 应收账款Accounts Receivable 减：应收账款坏账准备Deduct: Bad Debt Reserve for Accounts Receivable 应收账款净额Net Value of Accounts Receivable 其他应收款Other Receivable 减：其他应收款坏账准备Deduct: Bad Debt Reserve for Other Receivable 其他应收款净额Net Value of Other Receivable 预付账款Prepayment 应收补贴款Subsidy Receivable 存货Inventory 减：存货跌价准备Deduct: Inventory Falling Price Reserve 存货净额Net Value of Inventory 已完工尚未结算款Amount Due from Customer for Contract Work 待摊费用Deferred Expense 一年内到期的长期债权投资Long-term Investment on Bonds Due within One Year 一年内到期的应收融资租赁款Financial Lease Receivable Due within One Year 其他流动资产Other Current Assets 流动资产合计Total Current Assets 长期投资Long-term Investment 长期股权投资Long-term Investment on Stocks 委托贷款Entrusted Loan 长期债权投资Long-term Investment on Bonds 长期投资合计Total Long-term Investment 减：长期股权投资减值准备Deduct: Depreciation Reserve for Long-term Investment on Stocks 减：长期债权投资减值准备Deduct: Depreciation Reserve for Long-term Investment on