LM10L中文资料
LM10L
LINEARlight Colormix Flex
Data Sheet
Picture for Datasheet is missing
!!!
Benefits
Flexible self-adhesive module for special coloreffects and moods
?
Each LED contains red, green and blue emitters: optimum colormixing
?
Applications
Dynamic color applications
?Edge-lighting of transparent or diffused materials
?
Path & contour marking
?
Technical Features
Maximum total power:
LM10L-RGB/RGB2: 55,2 / 50,5 W
?Maximum total brightness:
LM10L-RGB/RGB2: 600/1285 lm
?Smallest unit of 10 LEDs can be cut out at
regular intervals without damaging the rest of the module
?Size of printed circuit board (L x W x H):
4000 mm x 11,5 mm x 2,2 mm
?Driven best by power supply OSRAM
OPTOTRONIC?: OT6, OT8, OT20, OT75/E
?Integrated controll gear/ power supply
- OT EASY 60 driving one LM10L - OT DALI 25
?Digital controllgear: DALI/ DMX
- OT RGB DMX DIM
- DALI EASY + OTi DALI DIM
?Analog controllgear with 1-10V interface:
- OT RGB DIM
- OT RGB Sequenzer
?Color Voltage [V DC]*Power [W]*Radiance Angle [°]*
Wavelength [nm] Color Temp [K]*
Lum. Flux [lm]*
Current [A]*Product
Number of LEDs
Technical Operating Data
red 2412,11206253850,5LM10L-RGB2-B7 +200green 2424,01205257701LM10L-RGB2-B7 +200blue 2414,41204671300,6LM10L-RGB2-B7 +200red 2412,11206253850,5LM10L-RGB2-B8 +200green 2424,01205287701LM10L-RGB2-B8 +200blue 2414,41204721300,6LM10L-RGB2-B8 +200red 2412,01206172130,5LM10L-RGB-B7200green 2424,01205253361LM10L-RGB-B7200blue 2419,2120467540,8LM10L-RGB-B7200red 2412,01206172130,5LM10L-RGB-B8200green 2424,01205253361LM10L-RGB-B8200blue
24
19,2
120
472
54
0,8
LM10L-RGB-B8
200
Preliminary Data
+)All Data are related to the entire module
Due to the special conditions of the manufacturing processes of LED the typical data of technical parameters can only reflect statistical figures and do not necessarily correspond to the actual parameters of each single product which could differ from the typical data. This product was not optimized for white light illumination.
*)
Drawing
Drawing is missing !!!
Operating Temperature at Tc-Point [ °C ] *
Storage Temperature
[ °C ] *
Product
Voltage Range [ V dc ] *Reverse Voltage
[ V dc ] *
Minimum and Maximum Ratings
LM10L-RGB2-B7 +232525...-3075-4085......LM10L-RGB2-B8 +232525...-3075-4085......LM10L-RGB-B7232525...-3075-4085......LM10L-RGB-B82325
25
...-3075
-4085
......Exceeding maximum ratings for operation and storage temperature will reduce expected life time or destroy the LED Module.Exceeding maximum ratings for operation voltage will cause hazardous overload and will likely destroy the LED Module.
The temperature of the LED module needs to measured at the Tc-point according to EN60598-1 in a thermally constant status with a temperature sensor or a temperature sensitive label. For exact location of the Tc-point see drawing below.
*)
Safety Information
The LED module itself and all its components may not be mechanically stressed.?Assembly must not damage or destroy conducting paths on the circuit board.
?Parallel connection is highly recommended as safe electrical operation mode.
Serial connection is not recommended. Unbalanced voltage drop can cause hazardous overload and damage the LED module.Correct electrical polarity needs to be observed. Wrong polarity will result in no light emission.
???Please ensure that the power supply is of adequate power to operate the total load.
?When mounting on metallic or otherwise conductive surfaces, there needs to be a electrical isolation at soldering points between module and the mounting surface.?The maximum run length of LINEARlight Colormix Flex LM10L from any power feed should be limited to 4000 mm.?Pay attention to standard ESD precautions when installing the module.
?The module, as manufactured, has no conformal coating and therefore offers no inherent protection against corrosion. The ability to customize the length of the module by cutting at specifically marked points is a key feature of the product and hence the reason for no factory installed conformal coating. For these reasons, it is recommended that the user complete all module modifications first (cutting, wiring) and then apply a conformal coating in the final stages of installation.?Damage by corrosion will not be honored as a materials defect claim. It is the user′s responsibility to provide suitable protection against corrosive agents such as moisture and condensation and other harmful elements.?For applications involving exposure to humidity and dust the module must be protected by a fixture or housing with a suitable protection class. The module can be protected against condensation water by treatment with an appropriate circuit board grade conformal coating. The conformal coating should have the following features:- Optical transparency - UV-resistance
- thermal expansion matching the thermal expansion of the module 15-30*10^-6 cm/cm/K - low permeability of steam for all climatic conditions - resistance against corrosive environment
The lacquer APL of the company Electrolube https://www.wendangku.net/doc/ff16216652.html, met the conditions for the LINEARlight Flex in our tests.
Installation of LED modules (with power supplies) needs to be made with regard to all applicable electrical and safety standards. Only qualified personnel should be allowed to perform installations.?The LED Module incorporates no protection against short circuits, overload or overheating. Therefore it is absolutely necessary to operate the modules with a electronically stabilised power supply offering protection against the above mentioned safety risks.For dimming applications attention should be paid to specific references in "OPTOTRONIC ? Technical Guide".
OSRAM OPTOTRONIC ? power supplies are specifically designed with protection features for safe operation.
When using power supplies other than OPTOTRONIC ? the following basic safety features are required, in addition to any other application specific concerns and local safety codes:Short circuit protection ?Overload protection Overheat protection
??
Assembly Information
?Solder connections should only be performed on designated solder pads (marked "24V +/RGB"). During soldering, do not exceed the maximum soldering time of 10 seconds and the maximum soldering temperature of 260°C.?The smallest unit (200 mm- 10 LEDs) can be removed by cutting with scissors between the designated solder pads.
?The mounting of the module is facilitated by means of the double-sided adhesive on the back-surface of the module. Care must be taken to provide a clean and dry mounting surface, free of oils or silicone coatings as well as dirt particle. The mounting substrate must have sufficient structural integrity. Take care to completely remove the adhesive backing. Once the module is appropriately positioned, press on the module with about 20N/cm2 (refer to application techniques of 3M adhesive transfer tapes).?The minimum bending radius is 2 cm. The module may be bent over a smaller radius but only in regions of the circuit board containing no electronic components and such bends should be made once and fixed in position to avoid cyclic fatigue.?The thermal length expansion coefficient of the modul is 17*10^-6cm/cm/K. When installing in environments with large variations in temperature (e.g. outdoor applications) and operating length of more than 2 m, the use of metallic mounting surfaces is necessary. Otherwise it is advisable to use an additional thicker adhesive tape to absorb the stress of any mismatch in expansion coefficients.
Related and Further Information
The new dimension of light ?153 S006 GB New creativity in lighting design LED Modules for illuminated signs ?138 W002 GB OPTOTRONIC? Technical Guide
?130 T008 GB
OPTOTRONIC? Technical Guide - Download:
Electronic Control Gear - Handbook OPTOTRONIC??https://www.wendangku.net/doc/ff16216652.html,/service_corner/download_cen ter
OSRAM LED systems
?https://www.wendangku.net/doc/ff16216652.html,/products/led-systems
Sales and Technical Support
Sales and technical support is given by the local OSRAM subsidiaries.
On our world wide homepage all OSRAM subsidiaries are listed with complete address and phone numbers.
OSRAM GmbH Hellabrunner Strasse 1D - 81536 München Germany
https://www.wendangku.net/doc/ff16216652.html, +49 (0)89 6213-0
Productgroup
Productname EAN *
S-Unit *Ordering Guide
LINEARlight Colormix Flex LM10L-RGB2-B7 +40083211694028LINEARlight Colormix Flex LM10L-RGB2-B8 +40083211694268LINEARlight Colormix Flex LM10L-RGB-B740083210088248LINEARlight Colormix Flex
LM10L-RGB-B8
4008321008886
8
EAN: Ordering number per single module S-Unit: Modules per shipping unit
*) Note: Typical performance data are subject to change without any further notice, particularly as LED technology evolves.