外文参考资料及译文封面
毕业设计（论文）外文参考
资料及译文
译文题目：英文题目
中文题目（题目外面不加括号）学生姓名：学号：
专业：
所在学院：
指导教师：赵海霞
职称：副教授
年月日
1、说明：
要求学生结合毕业设计（论文）课题参阅一篇以上的外文资料，并翻译至少一万印刷符（或译出3千汉字）以上的译文。
2、整篇文档的结构为（封面+英文+中文）。中文需要另起一页，不要直接接在英文后面。
中文用宋体小四号字，英文用新罗马体12号字，行距为固定值20磅，首行缩进。版面上空2.5cm，下空2cm，左空2.5cm，右空2cm。
（1）一级标题（如“1”，也可用“一”）（格式：小三号黑体居左）
（2）二级标题（如“1.1”，也可用“（一）”）（格式：四号黑体体居左）
（3）三级标题（如“1.1.1”，也可用“1”）（格式：小四号宋体居左）
3、英文资料若不是word文档，（例如pdf格式等），则另外附上英文原文。
Application and development
Of case based reasoning in fixture design
Abstract: Based on the case based designing (CBD) methodology, the fixture similarity is in two respects: the function and the structure information. Then, the computer aided fixture design system is created on case based reasoning (CBR),in which the attributes of the main features of workpiece and structure of fixture as case index code are designed for the retrieve of the similar cases, and the structure and hierarchical relation of case library are set up for store. Meanwhile, the algorithm based on the knowledge guided in the retrieve of the similar cases, the strategy of case adapt at ion and case storage in which the case ident if cat ion number is used to distinguish from similar cases are presented. The application of the system in some projects improves the design efficiency and gets a good result .
Keywords: case based reasoning ;fixture design; computer aided design(CAD)
Fixtures are devices that serve as the purpose of holding the workpiece securely and accurately, and maintaining a consistent relationship with respect to the tools while machining. Because the fixture structure depends on the feature of the product and the status of the process planning in the enterprise, its design is the bottleneck during manufacturing, which restrains to improve the efficiency and leadtime. And fixture design is a complicated process, based on experience that needs comprehensive qualitative knowledge about a number of design issues including workpiece configuration, manufacturing processes involved, and machining environment. This is also a very time consuming work when using traditional CAD tools (such as Unigraphics, CATIA or Pro/E), which are good at performing detailed design tasks, but provide few benefits for taking advantage of the previous design experience and resources, which are precisely the key factors in improving the efficiency. The methodology of case based reasoning (CBR) adapts the solution of a previously solved case to build a solution for a new problem with the following four steps: retrieve, reuse, revise, and retain [1]. This is a more useful method than the use of an expert system to simulate human thought because proposing a similar case and
applying a few modifications seems to be self explanatory and more intuitive to humans .So various case based design support tools have been developed for numerous areas[2-4], such as in injection molding and design, architectural design, die casting die design, process planning, and also in fixture design. Sun used six digitals to compose the index code that included workpiece shape, machine portion, bushing, the 1st locating device, the 2nd locating device and clamping device[5]. But the system cannot be used for other fixture types except for drill fixtures, and cannot solve the problem of storage of the same index code that needs to be retained, which is very important in CBR[6].
1 Construction of a Case Index and Case Library
1.1 Case index
The case index should be composed of all features of the workpiece, which are distinguished from different fixtures. Using all of them would make the operation in convenient. Because the forms of the parts are diverse, and the technology requirements of manufacture in the enterprise also develop continuously, lots of features used as the case index will make the search rate slow, and the main feature unimportant, for the reason that the relative weight which is allotted to every feature must diminish. And on the other hand, it is hard to include all the features in the case index.
Therefore, considering the practicality and the demand of rapid design, the case index includes both the major feature of the workpiece and the structure of fixture. The case index code is made up of 16 digits: 13 digits for case features and 3 digits for case identification number.
The first 13 digits represent 13 features. Each digit is corresponding to an attribute of the feature, which may be one of“*”, “？”, “1”, “2”,…,“A”,“B”,…,“Z”,…, etc. In which, “*”means anyone, “?”uncertain, “0”nothing.
The system rules: fixture type, workpiece shape, locating model cannot be “*”or“?”. When the system is designed, the attribute information of the three items does not have these options, which means the certain attribute must be selected.
The last three digits are the case identification number, which means the 13
digits of the case feature are the same, and the number of these three digits is used for distinguishing them.
The system also rules: “000”is a prototype case, which is used for retrieval, and other cases are “001”,“002”,…,which are used for reference cases to be searched by designers. If occasionally one of them needs to be changed as the prototype case, first it must be required to apply to change the one to “000”, and the former is changed to referential case automatically.
The construction of the case index code is shown in Fig.1.
1.2 Case library
The case library consists of lots of predefined cases. Case representation is one of the most important issues in case based reasoning. So compounding with the index code,.
1.3 Hierarchical form of Case
The structure similarity of the fixture is represented as the whole fixture similarity, components similarity and component similarity. So the whole fixture case library, components case library, component case library of fixture are formed correspondingly. Usually design information of the whole fixture is composed of workpiece information and workpiece procedure information, which represent the fixture satisfying the specifically designing function demand. The whole fixture case is made up of function components, which are described by the function components’names and numbers. The components case represents the members. (function component and other structure components，main driven parameter, the number, and their constrain relations.) The component case (the lowest layer of the fixture) is the structure of function component and other components. In the modern fixture design there are lots of parametric standard parts and common non standard parts. So the
component case library should record the specification parameter and the way in which it keeps them.
2 Strategy of Case Retrieval
In the case based design of fixtures ,the most important thing is the retrieval of the similarity, which can help to obtain the most similar case, and to cut down the time of adaptation. According to the requirement of fixture design, the strategy of case retrieval combines the way of the nearest neighbor and knowledge guided. That is, first search on depth, then on breadth; the knowledge guided strategy means to search on the knowledge rule from root to the object, which is firstly searched by the fixture type, then by the shape of the workpiece, thirdly by the locating method. For example, if the case index code includes the milling fixture of fixture type, the search is just for all milling fixtures, then for box of workpiece shape, the third for 1plane+ 2pine of locating method. If there is no match of it, then the search stops on depth, and returns to the upper layer, and retrieves all the relative cases on breadth.
Retrieval algorithms:
1)According to the case index information of fixture case library, search the relevant case library;
2)Match the case index code with the code of each case of the case library, and calculate the value of the similarity measure;
3)Sort the order of similarity measure, the biggest value, which is the most analogical case.
Similarity between two cases is based on the similarity between the two cases. features. The calculation of similarity measure depends on the type of the feature. The value of similarity can be calculated for numerical values, for example, compareWorkpiece with the weight of 50kg and 20kg. The value can also be calculated between non numerical values, for example, now the first 13 digits index code is all non numerical values. The similarity measure of a fixture is calculated as follows:
where S is the similarity measure of current fixture, n is the number of the index
feature, is the weight of each feature, is the similarity measure of
the attribute of the i2th feature with the attribute of relative feature of the j-th
case in the case library. At the same time, , the value counts as follows:
.
Where is the value of the index attribute of the i-th feature, and is the value of attribute of the relative i-th feature of the j-th case in case library.
So there are two methods to select the analogical fixture. One is to set the value. If the values of similarity measure of current cases were less than a given value, those cases would not be selected as analogical cases. When the case library is initially set up, and there are only a few cases, the value can be set smaller. If there are lots of analogical cases, the value should get larger. The other is just to set the number of the analogical cases (such as10), which is the largest value of similarity measure from the sorted order.
3 Case adaptation and Case Storage
3.1 Case adaptation
The modification of the analogical case in the fixture design includes the following three cases:
1) The substitution of components and the component;
2) Adjusting the dimension of components and the component while the form remains;
3) The redesign of the model.
If the components and component of the fixture are common objects, they can be edited, substituted and deleted with tools, which have been designed.
3.2 Case storage
Before saving a new fixture case in the case library, the designer must consider whether the saving is valuable. If the case does not increase the knowledge of the system, it is not necessary to store it in the case library. If it is valuable, then the designer must analyze it before saving it to see whether the case is stored as a prototype case or as reference case. A prototype case is a representation that can describe the main features of a case family. A case family consists of those cases whose index codes have the same first 13 digits and different last three digits in the case library. The last three digits of a prototype case are always “000”. A reference case belongs to the same family as the prototype case and is distinguished by the different last three digits.
From the concept that has been explained, the following strategies are adopted:
1) If a new case matches any existing case family, it has the same first 13 digits as an existing prototype case, so the case is not saved because it is represented well by the prototype case. Or is just saved as a reference case (the last 3 digits are not “000”, and not the same with others) in the case library.
2) If a new case matches any existing case family and is thought to be better at representing this case family than the previous prototype case, then the prototype case is substituted by this new case, and the previous prototype case is saved as a reference case.
3) If a new case does not match any existing case family, a new case family will be generated automatically and the case is stored as the prototype case in the case library.
4 Process of CBR in Fixture Design
According to the characteristics of fixture design, the basic information of the fixture design such as the name of fixture, part, product and the designer, etc. must be input first. Then the fixture file is set up automatically, in which all components of the fixture are put together. Then the model of the workpiece is input or designed. The detailed information about the workpiece is input, the case index code is set up, and then the CBR begins to search the analogical cases, relying on the similarity measure, and the most analogical case is selected out. If needed, the case is adapted to satisfy the current design, and restored into the case library. The flowchart of the process is shown in Fig.3.
5 Illustrating for Fixture Design by CBR
This is a workpiece (seeFig.4). Its material is 45# steel. Its name is seat. Its shape is block, and the product batch size is middle, etc. A fixture is turning fixture that serves to turn the hole, which needs to be designed.
The value of feature, attribute, case index code and weight of the workpiece is show n in Tab.2.
Through searching, and calculating the similarity, the case index code of the most similar case is 19325513321402000, and the detailed information is show n in Tab. 3.
The similarity is calculated as follows:
So the value of similarity measure of the fixture which needs to be designed with the most analogical case in case library is 0.806, and the structure of the most analogical case is shown in Fig.5.
After having been substituted the component, modified the locating model and clamp model, and adjusted the relative dimension, the new fixture is designed, and the figure is show n in Fig.6.
As there is not the analogical fixture in the case library, the new fixture is restored in to the case library. The case index code is 19325513311402000.
6 Conclusion
CBR, as a problem solving methodology, is a more efficient method than an expert system to simulate human thought, and has been developed in many domains where knowledge is difficult to acquire. The advantages of the CBR are as follows: it resembles human thought more closely; the building of a case library which has self learning ability by saving new cases is easier and faster than the building of a rule library; and it supports a better transfer and explanation of new knowledge that is more different than the rule library. A proposed fixture design framework on the CBR has been implemented by using Visual C ++, UG/Open API in U n graphics with Oracle as database support, which also has been integrated with the 32D parametric common component library, common components library and typical fixture library. The prototype system, developed here, is used for the aviation project, and aids the fixture designers to improve the design efficiency and reuse previous design resources.
毕业论文英文参考文献与译文
Inventory management Inventory Control On the so-called "inventory control", many people will interpret it as a "storage management", which is actually a big distortion. The traditional narrow view, mainly for warehouse inventory control of materials for inventory, data processing, storage, distribution, etc., through the implementation of anti-corrosion, temperature and humidity control means, to make the custody of the physical inventory to maintain optimum purposes. This is just a form of inventory control, or can be defined as the physical inventory control. How, then, from a broad perspective to understand inventory control? Inventory control should be related to the company's financial and operational objectives, in particular operating cash flow by optimizing the entire demand and supply chain management processes (DSCM), a reasonable set of ERP control strategy, and supported by appropriate information processing tools, tools to achieved in ensuring the timely delivery of the premise, as far as possible to reduce inventory levels, reducing inventory and obsolescence, the risk of devaluation. In this sense, the physical inventory control to achieve financial goals is just a means to control the entire inventory or just a necessary part; from the perspective of organizational functions, physical inventory control, warehouse management is mainly the responsibility of The broad inventory control is the demand and supply chain management, and the whole company's responsibility. Why until now many people's understanding of inventory control, limited physical inventory control? The following two reasons can not be ignored: First, our enterprises do not attach importance to inventory control. Especially those who benefit relatively good business, as long as there is money on the few people to consider the problem of inventory turnover. Inventory control is simply interpreted as warehouse management, unless the time to spend money, it may have been to see the inventory problem, and see the results are often very simple procurement to buy more, or did not do warehouse departments . Second, ERP misleading. Invoicing software is simple audacity to call it ERP, companies on their so-called ERP can reduce the number of inventory, inventory control, seems to rely on their small software can get. Even as SAP, BAAN ERP world, the field of
英文文献翻译
中等分辨率制备分离的 快速色谱技术 W. Clark Still,* Michael K a h n , and Abhijit Mitra Departm(7nt o/ Chemistry, Columbia Uniuersity,1Veu York, Neu; York 10027 ReceiLied January 26, 1978 我们希望找到一种简单的吸附色谱技术用于有机化合物的常规净化。这种技术是适于传统的有机物大规模制备分离，该技术需使用长柱色谱法。尽管这种技术得到的效果非常好，但是其需要消耗大量的时间，并且由于频带拖尾经常出现低复原率。当分离的样本剂量大于1或者2g时，这些问题显得更加突出。近年来，几种制备系统已经进行了改进，能将分离时间减少到1-3h，并允许各成分的分辨率ΔR f≥（使用薄层色谱分析进行分析）。在这些方法中，在我们的实验室中，媒介压力色谱法1和短柱色谱法2是最成功的。最近，我们发现一种可以将分离速度大幅度提升的技术，可用于反应产物的常规提纯，我们将这种技术称为急骤色谱法。虽然这种技术的分辨率只是中等（ΔR f≥），而且构建这个系统花费非常低，并且能在10-15min内分离重量在的样本。4 急骤色谱法是以空气压力驱动的混合介质压力以及短柱色谱法为基础，专门针对快速分离，介质压力以及短柱色谱已经进行了优化。优化实验是在一组标准条件5下进行的，优化实验使用苯甲醇作为样本，放在一个20mm*5in.的硅胶柱60内，使用Tracor 970紫外检测器监测圆柱的输出。分辨率通过持续时间（r）和峰宽（w,w/2）的比率进行测定的（Figure 1），结果如图2-4所示，图2-4分别放映分辨率随着硅胶颗粒大小、洗脱液流速和样本大小的变化。
机械设计中英文外文翻译文献
(文档含英文原文和中文翻译) 中英文资料外文翻译 Fundamentals Of Machinery Design This introductory chapter is a general survey of machinery design．First it presents the definition and major role of machinery design，the relationship between machinery
and its components．Then it gives an overview of machinery design as a fundamental course and outlines a general procedure of machinery design followed by all the engineers．Finally, it lists the contents of the course and the primary goals to be achieved． 1．1 The role of machinery design Machinery design is to formulate all engineering plan．Engineering in essence is to utilize the existing resources and natural law to benefit humanity．As a major segment of engineerin，machinery design involves a range of disciplines in materials，mechanics，heat，flow，control，electronics and production．Although many high technologies are computerized and automated，and are rapidly merged into Our daily life，machines are indispensable for various special work that is difficult or impracticable to be carried out by human．Moreover，machinery can significantly improve efficiency and quality of production，which is crucial in current competitive global market． In the modern industrialized world，the wealth and living standards of a nation are closely linked with their capabilities to design and manufacture engineering products．It can be claimed that the advancement of machinery design and manufacturing can remarkable promote the overall level of a country’s industrialization．Those nations，who do not perform well in design and manufacture fields，are not competitive in world markets．It is evident that several countries that used to be leaders in the design and manufacturing sectors until the l 960s and the 1 970s had，by the l990s，slipped back and lost their leadership．On the contrary, our Country is rapidly picking up her position in manufacturing industry since the l 9 80s and is playing a more and more vital role in the global market．To accelerate such an industrializing process of our country, highly skilled design engineers having extensive knowledge and expertise are needed．That is why the course of machinery design is of great significance for students of engineering． The course of machinery design is considerable different from those background subjects in science and mathematics．For many students，it is perhaps one of their basic professional engineering courses concerned with obtaining solutions to practical problem s．Definitely these solutions must clearly represent an understanding of the underlying science，usually such an understanding may not be sufficient，empirical knowledge or engineering judgement has to be also involved．Furthermore，due to be professional nature of this subject，most design problems may not have one right solution．Nevertheless it is achievable to determine a better design from all feasible solutions． 1．2 Machinery and components A state-of-the-art machine may encompass all or part of mechanical，electrical，control，sensor，monitoring and lubricating sub—systems．In
毕业设计(论文)外文文献译文
毕业设计（论文） 外文文献译文及原文 学生：李树森 学号：201006090217 院（系）：电气与信息工程学院 专业：网络工程 指导教师：王立梅 2014年06月10日
JSP的技术发展历史 作者：Kathy Sierra and Bert Bates 来源：Servlet&JSP Java Server Pages(JSP)是一种基于web的脚本编程技术，类似于网景公司的服务器端Java脚本语言—— server-side JavaScript(SSJS)和微软的Active Server Pages(ASP)。与SSJS和ASP相比，JSP具有更好的可扩展性，并且它不专属于任何一家厂商或某一特定的Web服务器。尽管JSP规范是由Sun 公司制定的，但任何厂商都可以在自己的系统上实现JSP。 在Sun正式发布JSP之后，这种新的Web应用开发技术很快引起了人们的关注。JSP为创建高度动态的Web应用提供了一个独特的开发环境。按照Sun的说法，JSP能够适应市场上包括Apache WebServer、IIS4.0在内的85%的服务器产品。 本文将介绍JSP相关的知识，以及JavaBean的相关内容，当然都是比较粗略的介绍其中的基本内容，仅仅起到抛砖引玉的作用，如果读者需要更详细的信息，请参考相应的JSP的书籍。 1.1 概述 JSP(Java Server Pages)是由Sun Microsystems公司倡导、许多公司参与一起建立的一种动态网页技术标准，其在动态网页的建设中有其强大而特别的功能。JSP与Microsoft的ASP技术非常相似。两者都提供在HTML代码中混合某种程序代码、由语言引擎解释执行程序代码的能力。下面我们简单的对它进行介绍。 JSP页面最终会转换成servlet。因而，从根本上，JSP页面能够执行的任何任务都可以用servlet 来完成。然而，这种底层的等同性并不意味着servlet和JSP页面对于所有的情况都等同适用。问题不在于技术的能力，而是二者在便利性、生产率和可维护性上的不同。毕竟，在特定平台上能够用Java 编程语言完成的事情，同样可以用汇编语言来完成，但是选择哪种语言依旧十分重要。 和单独使用servlet相比，JSP提供下述好处： JSP中HTML的编写与维护更为简单。JSP中可以使用常规的HTML：没有额外的反斜杠，没有额外的双引号，也没有暗含的Java语法。 能够使用标准的网站开发工具。即使是那些对JSP一无所知的HTML工具，我们也可以使用，因为它们会忽略JSP标签。 可以对开发团队进行划分。Java程序员可以致力于动态代码。Web开发人员可以将经理集中在表示层上。对于大型的项目，这种划分极为重要。依据开发团队的大小，及项目的复杂程度，可以对静态HTML和动态内容进行弱分离和强分离。 此处的讨论并不是说人们应该放弃使用servlet而仅仅使用JSP。事实上，几乎所有的项目都会同时用到这两种技术。在某些项目中，更适宜选用servlet，而针对项目中的某些请求，我们可能会在MVC构架下组合使用这两项技术。我们总是希望用适当的工具完成相对应的工作，仅仅是servlet并不一定能够胜任所有工作。 1.2 JSP的由来 Sun公司的JSP技术，使Web页面开发人员可以使用HTML或者XML标识来设计和格式化最终
外文译文(封面及要求)
译文要求 1.翻译这些文章，所给英文作为参考。 摩擦发电体传感器在管道中的位置 材料科学与工程学院，乔治亚理工学院，亚特兰大，乔治亚0332-0245，美国，电子薄膜国家重点实验室薄膜与集成器件，光电信息学院，中国电子科技大学， 信息，科技，成都610054中国（电子科技大学），中国，和北京奈米能源和纳米技术研究院，中国科学院，北京，中国。^ Y. G.苏，朱，和杨同样对这项工作作出贡献。 摘要：我们讨论摩擦发电是基于单电极的摩擦，传感器（se-tes）用于检测物体的运动在管道中的位置。这项创新的优点具有成本低和好的效益，设计简单等，基于传感器se-tes薄膜环形铜电极和聚四氟乙烯（PTFE）管，原理是在对摩擦起电和静电之间的耦合作用的基础上感应。传感器的响应发电输出信号一个物体的机械运动（如球）通过电极。铜电极的线性阵列可以沿管在一侧的位置和运动的钢球速度的检测。信号—对这一器件达到的噪声比10 3。此外，我们证明了运动特征的实时监测和映射利用电极通道沿管一七单元阵列管内钢球，由输出触发（电流信号）LED灯泡作为一个滚动的球的位置的实时指标。另外。se-tes 也显示的检测在一个水管堵塞的能力。这项工作表明潜在的广泛应用在自摩擦电传感器驱动的跟踪系统堵塞检测，流量控制和物流监控。 关键字：摩擦电效应自发电跟踪传感器管道检测闭塞 发展定位与跟踪系统的应用是很重要的，交通运输，物流控制机，流量监测。通过电子信息手段确定一个对象的位置，然而直接的视频成像是移动计算机和物联网的关键技术。关键也就在于位置感应，具有LED的设计与实现，优化健在模式系统，尤其是计算能力和感应范围。 8年多来，主要是以搜索工作已经基于检测热和磁，然而一个常见的限制是大多数这类传感器长寿和移动性带来的挑战，最近，一类发电传发电传感器基于电纳-（滕氏介绍。）
计算机网络-外文文献-外文翻译-英文文献-新技术的计算机网络
New technique of the computer network Abstract The 21 century is an ages of the information economy, being the computer network technique of representative techniques this ages, will be at very fast speed develop soon in continuously creatively, and will go deep into the people's work, life and study. Therefore, control this technique and then seem to be more to deliver the importance. Now I mainly introduce the new technique of a few networks in actuality live of application. keywords Internet Network System Digital Certificates Grid Storage 1. Foreword Internet turns 36, still a work in progress Thirty-six years after computer scientists at UCLA linked two bulky computers using a 15-foot gray cable, testing a new way for exchanging data over networks, what would ultimately become the Internet remains a work in progress. University researchers are experimenting with ways to increase its capacity and speed. Programmers are trying to imbue Web pages with intelligence. And work is underway to re-engineer the network to reduce Spam (junk mail) and security troubles. All the while threats loom: Critics warn that commercial, legal and political pressures could hinder the types of innovations that made the Internet what it is today. Stephen Crocker and Vinton Cerf were among the graduate students who joined UCLA professor Len Klein rock in an engineering lab on Sept. 2, 1969, as bits of meaningless test data flowed silently between the two computers. By January, three other "nodes" joined the fledgling network.
建筑类外文文献及中文翻译
forced concrete structure reinforced with an overviewRein Since the reform and opening up, with the national economy's rapid and sustained development of a reinforced concrete structure built, reinforced with the development of technology has been great. Therefore, to promote the use of advanced technology reinforced connecting to improve project quality and speed up the pace of construction, improve labor productivity, reduce costs, and is of great significance. Reinforced steel bars connecting technologies can be divided into two broad categories linking welding machinery and steel. There are six types of welding steel welding methods, and some apply to the prefabricated plant, and some apply to the construction site, some of both apply. There are three types of machinery commonly used reinforcement linking method primarily applicable to the construction site. Ways has its own characteristics and different application, and in the continuous development and improvement. In actual production, should be based on specific conditions of work, working environment and technical requirements, the choice of suitable methods to achieve the best overall efficiency. 1、steel mechanical link 1.1 radial squeeze link Will be a steel sleeve in two sets to the highly-reinforced Department with superhigh pressure hydraulic equipment (squeeze tongs) along steel sleeve radial squeeze steel casing, in squeezing out tongs squeeze pressure role of a steel sleeve plasticity deformation closely integrated with reinforced through reinforced steel sleeve and Wang Liang's Position will be two solid steel bars linked Characteristic: Connect intensity to be high, performance reliable, can bear high stress draw and pigeonhole the load and tired load repeatedly.
英文参考文献翻译完结
基于反馈神经网络肘关节力矩的动态预测 R.Song K.Y.Tong 健康技术与信息学系，香港理工大学 KowIoon，香港
摘要 肌肉模型是身体部分运动分析的一个重要组成部分。尽管许多研究已经集中在静态条件下,但是肌电信号（EMG）和关节转矩在自愿动态情况下之间的关系并没有被很好的研究。本研究的目的是调查的一个反馈人工神经网络的性能（RANN）自愿动态情况下的复杂肘扭矩估计。肌电信号和运动数据，其中包括角度和角速度，被用来作为估计在运动过程中预期的扭矩输入。此外，角度和角速度的预测精度的作用进行了研究，并比较两个模型。一个模型的肌电图和关节运动的投入和其他的模型只使用肌电图无运动数据输入。六例健康体检者，和两个平均角速度（60°S 7和90°S 7）三种不同负荷（0公斤，1公斤，2公斤）在手的位置被选择来训练和测试90°屈肘、全伸肘之间的递归神经网络（0 ~）。训练结束后，根平均平方误差（RMSE）预期的扭矩和扭矩之间的模型预测，在训练数据集的肌电图和关节运动的投入和测试数据集，分别为0.17±0.03 nm和0.35 + 0.06 nm。预期的扭矩和预测模型的RMSE值之间的扭矩，在训练数据集只有肌电输入和测试集，分别为0.57 t - 0.07 nm和0.73 T 0.11 nm。结果表明，肌电信号一起运动的数据提供了更好的性能预测的关节力矩；关节角度和角速度提供了重要信息的关节力矩的估计在自愿的运动。 关键词:肌肉骨骼模型，自愿的运动，反馈人工神经网络，逆动力学模型
第一章绪论 由于希尔提出了1938肌肉的经典论文，神经生理学和神经肌肉骨骼系统的生物力学已被广泛研究，使人体运动生成的原理可以发现（希尔，1938）。 探讨中枢神经系统（CNS）激发肌肉和其后的发展力和产生不同的人体运动，许多模型来描述和定性的肌肉骨骼系统的不同层次的性能（温特斯，1990；扎杰克和温特斯，1990）。一个被普遍接受的山为基础的神经肌肉骨骼系统由以下子模型，一步一步：肌肉兴奋-收缩模型；肌腱骨骼模型；动态模型（扎耶克，1989）。 图1 肌肉骨骼模型框图 图1显示了基于hillbased模型的运动生成。图1，肌肉兴奋收缩模型是用来估计中枢神经系统指挥肌肉活动的状态。肌腱模型产生的肌肉力量不仅基于肌肉激活状态，而且基于肌腱式长度和肌腱式收缩速度，这与关节角速度和角速度（温特斯和斯塔克，1988）。前项状态的肌肉力量，它决定了肌腱的依从性，还负责肌肉力在后一阶段（扎耶克，1989）。一旦所有负责的关节运动的肌肉力量已经发现，肌肉的力量与各自的肌肉力臂和的结果求和乘法可以产生关节力矩。所有子模型的数学积分可以用来描述关节运动是中枢神经系统的命令产生哪些参数斧负责关节力矩。 肌电信号反映肌肉的活动，和许多类似的肌电力矩的关系已经在静态和动态情况的研究（张等人，1997；麦森纳和莫润，1995）。肌肉的肌电信号也常被认
变电站_外文翻译_外文文献_英文文献_变电站的综合概述
英文翻译 A comprehensive overview of substations Along with the economic development and the modern industry developments of quick rising, the design of the power supply system become more and more completely and system. Because the quickly increase electricity of factories, it also increases seriously to the dependable index of the economic condition, power supply in quantity. Therefore they need the higher and more perfect request to the power supply. Whether Design reasonable, not only affect directly the base investment and circulate the expenses with have the metal depletion in colour metal, but also will reflect the dependable in power supply and the safe in many facts. In a word, it is close with the economic performance and the safety of the people. The substation is an importance part of the electric power system, it is consisted of the electric appliances equipments and the Transmission and the Distribution. It obtains the electric power from the electric power system, through its function of transformation and assign, transport and safety. Then transport the power to every place with safe, dependable, and economical. As an important part of power’s transport and control, the transformer substation must change the mode of the traditional design and control, then can adapt to the modern electric power system, the development of modern industry and the of trend of the society life. Electric power industry is one of the foundations of national industry and national economic development to industry, it is a coal, oil, natural gas, hydropower, nuclear power, wind power and other energy conversion into electrical energy of the secondary energy industry, it for the other departments of the national economy fast and stable development of the provision of adequate power, and its level of development is a reflection of the country's economic development an important indicator of the level. As the power in the industry and the importance of the national economy, electricity transmission and distribution of electric energy used in these areas is an indispensable component.。Therefore, power transmission and distribution is critical. Substation is to enable superior power plant power plants or power after adjustments to the lower load of books is an important part of power transmission. Operation of its functions, the capacity of a direct impact on the size of the lower load power, thereby affecting the industrial production and power consumption.Substation system if a link failure, the system will protect the part of action. May result in power outages and so on, to the production and living a great disadvantage. Therefore, the substation in the electric power system for the protection of electricity reliability,
2021年毕业设计论文外文文献翻译要求及封面
杭州电子科技大学 毕业设计（论文）外文文献翻译 毕业设计（论文）题目 液压制动器基本 翻译（1）题目 有用产品 翻译（2）题目 学院机械学院 专业车辆工程 姓名 班级 学号 指引教师
液压制动基本 空气制动系统得到更多关注，但更多车辆上安装液压制动器。理解它们 是如何工作，是安全，具成本效益诊断和修复第一步。 有无想过为什么不能只是其中一种制动？这是由于空气和液压制动器，使一种或某些应用程序其她抱负经营特色。重型组合车辆，空气是明确选取，由于将需要大量液体阿卡迪亚所有分泵。此外，布满液压油与制动分泵和软管将是混乱。但对于轻型和中型卡车直应用，液压制动器提供优势涉及： ?制动感觉- 那就是，踏板越往下压，努力增长;高线压力，容许使用更轻，更紧凑制动组件; ?更少初始费用，由于用更小和更少元件; ?卫生，液压制动器是封闭系统; ?易于定位泄漏，由于液体是可见。液压制动系统有更多排列，比在空气系统中发现，但都基本相似。 液压系统 所有液压制动系统包括流体水库，主缸，液压，液压管路，对制动器进行加压流体软管和一种或各种轮缸（S）对每个车轮产生。分泵扩大流体压力下，迫使制动蹄对鼓内侧。如果使用盘式制动器，卡钳与不可分割气瓶打击转子时施加压力。由于车辆必要可以更迅速，它可以加速到停止，需要大量刹车力。因而，必要减速刹车产生马力发动机作用多次。为了发展须持有对鼓或盘制动器衬片力量，实现受控减速，这是要乘原始力量施加在刹车踏板。 当使用液压系统，机械杠杆是在脚踏板联动。然而，不同分泵或卡尺直径直径，关系到主缸内径，提供了一种额外增长比率。液压系统中，各分泵交付压力，直接影响由活塞地区。例如，如果一种轮缸活塞面积2平方英寸，另一种活塞面积1平方英寸，系统压力为400磅，2平方英寸活塞将针对制动器推一种迫使800
机电专业论文英文文献及其中文译文
毕业论文外文文献翻译译文题目:INTEGRATION OF MACHINERY 外文资料翻译资料来源：文章名：INTEGRATION OF MACHINERY 《Digital Image Processing》书刊名：作者：Y. Torres J. J. Pavón I. Nieto and J. A.Rodríguez 章节：2.4 INTEGRATION OF MACHINERY INTEGRATION OF MACHINERY （From ELECTRICAL AND MACHINERY INDUSTRY）ABSTRACT Machinery was the modern science and technology development inevitable resultthis article has summarized the integration of machinery technology basic outlineand the development background .Summarized the domestic and foreign integration ofmachinery technology present situation has analyzed the integration of machinerytechnology trend of development. Key word：integration of machinery ，technology，present situation ，productt，echnique of manufacture ，trend of development 0. Introduction modern science and technology unceasing development impelleddifferent discipline intersecting enormously with the seepage has caused the projectdomain technological revolution and the transformation .In mechanical engineeringdomain because the microelectronic technology and the computer technology rapiddevelopment and forms to the mechanical industry seepage the integration of machinerycaused the mechanical industry the technical structure the product organizationthe function and the constitution the production method and the management systemhas had the huge change caused the industrial production to enter into quottheintegration of machineryquot by quotthe machinery electrificationquot for the characteristicdevelopment phase. 1. Integration of machinery outline integration of machinery is refers in theorganization new owner function the power function in the information processingfunction and the control function introduces the electronic technology unifies thesystem the mechanism and the computerization design and the software whichconstitutes always to call. The integration of machinery development also has becomeone to have until now own system new discipline not only develops along with thescience and technology but also entrusts with the new content .But its basiccharacteristic may summarize is: The integration of machinery is embarks from thesystem viewpoint synthesis community technologies and so on utilization mechanicaltechnology microelectronic technology automatic control technology computertechnology information technology sensing observation and control technologyelectric power electronic technology connection technology information conversiontechnology as well as software programming technology according to the systemfunction goal and the optimized organization goal reasonable disposition and thelayout various functions unit in multi-purpose high grade redundant reliable inthe low energy consumption significance realize the specific function value andcauses the overall system optimization the systems engineering technology .From thisproduces functional system then becomes an integration of machinery systematic orthe integration of machinery product. Therefore quotintegration of machineryquot coveringquottechnologyquot and quotproductquot two aspects .Only is the integration of machinerytechnology is based on the above community technology organic fusion one kind ofcomprehensive