当前位置：文档库 › A11503RNZQ中文资料

A11503RNZQ中文资料

Rotary

Models Available

Features/Benefits

?Multi-pole and multi-position ?Positive detent

?Shorting & non-shorting contacts ?Panel and PCB mounting

Typical Applications ?Automotive

?Major and small appliances ?Industrial equipment

Specifications

CONTACT RATING: Q contact material: Switch - 2.5 AMPS @

125 V AC; 350 mA @ 125 V DC (UL/CSA). Carry - 5 AMPS continuous. See page L-6 for additional ratings.

ELECTRICAL LIFE: 15,000 make-and-break cycles at full load up

to 300,000 detent operations.

CONTACT RESISTANCE: Below 20 m ?typ. initial @

2-4 V DC, 100 mA, for both silver and gold plated contacts.INSULATION RESISTANCE: 10 9?min.

DIELECTRIC STRENGTH: 1,000 Vrms min. @ sea level.

Operating and storage temp: -30o to 85oC

OPERATING & STORAGE TEMPERATURE: -30oC to 85oC

NOTE:Any models supplied with Q, B or G contact material are RoHS compliant. For the latest information regarding RoHS compliance, please go to: https://www.wendangku.net/doc/37387051.html,/rohs.NOTE:Specifications and materials listed above are for switches with standard options.For information on specific and custom switches, consult Customer Service Center.

Materials

HOUSING & BUSHING: Glass filled 6/6 nylon (UL 94V-0).ACTUATOR: Glass filled 6/6 nylon (UL 94V-0).

MOVABLE CONTACTS: Q contact material: Coin silver, silver plated.

See page L-6 for additional contact materials.

STATIONARY CONTACTS & TERMINALS: Q contact material: Brass,

silver plated. See page L-6 for additional contact materials.HARDWARE: Nut - zinc, nickel plated. Lockwasher — steel, bright

zinc plated. Stop Ring - brass, nickel plated.TERMINAL SEAL: Epoxy.

Build-A-Switch

T o order, simply select desired option from each category and place in the appropriate box. Available options are shown and described on pages L–4 through L–7. For additional options not shown in catalog, consult Customer Service Center.

Switch Function

A100SP ,30°Index,12 pos.no stops A102SPDT,30°Index A103SP ,30°Index,3 pos.A104SP ,30°Index,4 pos.A105SP ,30°Index,5 pos.A106SP ,30°Index,6 pos.A107SP ,30°Index,7 pos.A108SP ,30°Index,8 pos.A109SP ,30°Index,9 pos.A110SP ,30°Index,10 pos.A112SP ,30°Index,12 pos.A114SP ,90°Index,2 pos.A115SP ,45°Index,3 pos.A124SP ,90°Index,4 pos.

A125SP ,45°Index,8 pos.

A203DP ,30°Index,3 pos.

A204DP ,30°Index,4 pos.

A205DP ,30°Index,5 pos.

A206DP ,30°Index,6 pos.

A214DP ,90°Index,2 pos.

A3033P ,30°Index,3 pos.

A3043P ,30°Index,4 pos.

A4024PDT,30°Index

A4034P ,30°Index,3 pos

Contact Material Q Silver B Gold

G Gold over silver

Actuator 151.500" high,flatted 03.375" high,flatted 05.500" high,flatted 14 1.500" high,flatted 42 1.654" high,metric S1Screwdriver Slot Shorting/Non-shorting Contacts N Non-shorting contacts S Shorting contacts (Not available with models A114,A124 & A214)Terminations

Z Solder lug

C PC Thru-hole

MC Modular base

Seal NONE No seal E Epoxy seal

F Splashproof bushing seal

K Epoxy & splashproof bushing seal

Mounting Style R 3/8-32 threaded M M10 x .75 metric

R o t a r y

3P MODELS SCHEMATIC

4P MODELS SCHEMATIC

DP MODELS SCHEMATIC

SP MODELS SCHEMATIC

3P MODELS

TERMINAL NUMBERS

4P MODELS

SP MODELS (omit terminals B,C & D )DP MODELS (omit terminals B & D )

T erminal numbers molded on bottom of

housing.

NOTE: * These models with ‘C’ or ‘MC’ terminations have additional terminal no. 9as switch support only. This terminal is not connected electrically inside switch.All models with all options when ordered with ‘G’ or ‘Q’ contact material, see page L-6.

Rotary

SHORTING CONTACTS (make-before-break)

N NON-SHORTING CONTACTS (break-before-make)S1

SCREWDRIVER SLOT

1.654" METRIC

1.500" HIGH

.500" HIGH

.375" HIGH

NOTE:‘S’ shorting contacts are not available with A114, A124 and A214 models.

NOTE: Actuators shown in position 1, fully CCW.

R o t a r y

* Note: See Technical Data section of this catalog for RoHS compliant and compatible definition and specifications.

MOVABLE CONTACTS: Copper alloy, with gold plate over nickel plate.

STATIONARY CONTACTS & TERMINALS: Brass, with gold plate over nickel plate.2MOVABLE CONTACTS: Coin silver, silver plated.

STATIONARY CONTACTS & TERMINALS: Brass, silver plated (standard with all termination options).

3MOVABLE CONTACTS: Coin silver, with gold plate over nickel plate over silver plate.STATIONARY CONTACTS & TERMINALS: Brass, with gold plate over nickel plate over silver plate.

All models with all options when ordered with ‘G’ or ‘Q’ contact material.

NOTE:‘G’ contact material is equivalent to both ‘B’ and ‘Q” contact materials.

NOTE:Any models supplied with Q, B or G contact material are RoHS compliant. For the latest information regarding RoHS compliance, please go to: https://www.wendangku.net/doc/37387051.html,/rohs.

CONTACT AND OPTION CODE

TERMINAL MATERIAL

RATING

Q SWITCH-2.5 AMPS @ 125 V AC; 350 mA @ 125V DC (UL/CSA).CARRY-5 AMPS CONTINUOUS.LOW LEVEL/DRY CIRCUIT B SILVER 2POWER

0.4 VA MAX. @ 20 V AC or DC MAX

RoHS COMPLIANT*

RoHS

COMPATIBLE*

YES YES YES YES LOW LEVEL/DRY CIRCUIT OR POWER

YES

GOLD 1

GOLD OVER SILVER 3

0.4 VA MAX. @ 20 V AC or DC MAX. or SWITCH-2.5 AMPS @ 125 V AC;350 mA @ 125 V DC (UL/CSA). CARRY-5 AMPS CONTINUOUS.

AVAILABLE HARDWARE

(FIG. 1)

(FIG. 2)(FIG. 3)

REMOVABLE CLIP

LOCATING

T AB

STANDOFF

K EPOXY & SPLASHPROOF BUSHING SEAL

F SPLASHPROOF BUSHIN

G SEAL

NONE NO SEAL E EPOXY SEAL

Stop ring

PART NO.

767B00201

Material: Brass

Finish: Nickel plated

Setting Stops on A112 and A125 Models

The number of switch positions is adjustable on A112

and A125 models only by means of a stop ring provided

with each switch. The number of positions is pre-set on

all other models and the stop ring is factory installed.

Soldering

1. Insert switch base only into PC board.

2. Do not bend terminals.

3. Wave soldering recommended at

500F solder temperature.

4. Hand solder at 500F, 10 sec.

max./terminal.

Switch Assembly

1. Hold housing/shaft assembly by housing. Remove

protective cap by squeezing tabs and discard. (FIG. 1)

2. Do not push on switch shaft. Detent mechanism will

come apart.

3. While holding switch housing, align locating tab on

base with notch on housing and engage 4 housing

latches in slots on base. (FIG. 2)

4. Push firmly on housing until latches snap in place.

5. Remove clip from shaft and discard. Assembly is

complete. (FIG. 3)

Cleaning

1. Flux clean using vapor degreaser and forced

rinse or triple bath method.

To set stops: Turn shaft fully counter-clockwise and

insert stop ring tab in desired hole. Install lockwasher

and nut to retain stop ring for both PC and panel

mounting. Switch without stop ring has 12 positions. Soldering, Cleaning and Assembly Instructions for ‘MC’ Termination Option