54FCT245
Octal Bidirectional Transceiver with TRI-STATE ?Outputs
General Description
The ’FCT245contains eight non-inverting bidirectional buff-ers with TRI-STATE outputs and is intended for bus-oriented applications.Current sinking capability is 48mA on both the A and B ports.The Transmit/Receive (T/R)input determines the direction of data flow through the bidirectional trans-ceiver.Transmit (active HIGH)enables data from A ports to B ports;Receive (active LOW)enables data from B ports to A ports.The Output Enable input,when HIGH,disables both A and B ports by placing them in a High Z condition.
Features
n TTL input and output level compatible
n A and B output sink capability of 48mA,source capability of 12mA
n CMOS power consumption
n Standard Microcircuit Drawing (SMD)5962-8762901
Ordering Code:
Military Package Package Description
Number 54FCT245DMQB J20A 20-Lead Ceramic Dual-In-Line 54FCT245FMQB W20A 20-Lead Cerpak
54FCT245LMQB
E20A
20-Lead Ceramic Leadless Chip Carrier,Type C
Logic Symbol
TRI-STATE ?is a registered trademark of National Semiconductor Corporation.
DS100950-1
August 1998
54FCT245Octal Bidirectional Transceiver with TRI-STATE Outputs
?1998National Semiconductor Corporation https://www.wendangku.net/doc/3c4612197.html,
Connection Diagrams
Pin Descriptions
Pin Names Description
OE Output Enable Input (Active LOW)T/R Transmit/Receive Input
A 0–A 7Side A Inputs or TRI-STATE Outputs
B 0–B 7
Side B Inputs or TRI-STATE Outputs
Truth Table
Inputs Output
OE T/R L L Bus B Data to Bus A L H Bus A Data to Bus B H
X
High Z State
H =HIGH Voltage Level L =LOW Voltage Level X =Immaterial
Logic Diagram
Pin Assignment for DIP
and Flatpak.
DS100950-5
Pin Assignment for LCC
DS100950-4
https://www.wendangku.net/doc/3c4612197.html, 2
Absolute Maximum Ratings(Note1)
If Military/Aerospace specified devices are required, please contact the National Semiconductor Sales Office/ Distributors for availability and specifications.
Storage Temperature?65?C to+150?C Ambient Temperature under Bias?55?C to+125?C Junction Temperature under Bias
Ceramic?55?C to+175?C V CC Pin Potential to
Ground Pin?0.5V to+7.0V Input Voltage(Note2)?0.5V to+7.0V Input Current(Note2)?30mA to+5.0mA Voltage Applied to Any Output
in the Disabled or
Power-off State?0.5V to5.5V
in the HIGH State?0.5V to V CC Current Applied to Output
in LOW State(Max)twice the rated I OL(mA) Recommended Operating Conditions
Free Air Ambient Temperature
Military?55?C to+125?C Supply Voltage
Military+4.5V to+5.5V Note1:Absolute maximum ratings are values beyond which the device may be damaged or have its useful life impaired.Functional operation under these conditions is not implied.
Note2:Either voltage limit or current limit is sufficient to protect inputs.
DC Electrical Characteristics
Symbol Parameter FCT245
Units V CC Conditions
Min Max
V IH Input HIGH Voltage 2.0V Recognized HIGH Signal V IL Input LOW Voltage0.8V Recognized LOW Signal V CD Input Clamp Diode Voltage?1.2V Min I IN=?18mA(OE,T/R)
V OH Output HIGH
Voltage 54FCT 4.3V Min I OH=?300uA(A n,B n) 54FCT 2.4V Min I OH=?12mA(A n,B n)
V OL Output LOW
Voltage 54FCT0.2V Min I OL=300uA(A n,B n) 54FCT0.55V Min I OL=48mA(A n,B n)
I IH Input HIGH Current5
μA Max V IN=2.7V(OE,T/R)
5V IN=V CC(OE,T/R)
I BVIT Input HIGH Current Breakdown Test
(I/O)20μA Max
V IN=5.5V(A n,B n)
I IL Input LOW Current?5μA Max V IN=0.0V(OE,T/R) I OS Output Short-Circuit Current?60mA Max V OUT=0.0V(A n,B n)
I CCQ Power Supply Current
1.5mA Max V IN=0.2V or V IN=5.3V,V CC= 5.5V
?I CC Power Supply Current 2.0mA Max V CC=5.5V,V IN=3.4V
I CCT Total Power Supply Current
6.0mA V IN=3.4V or V IN=GND,OE= T/R=GND,V CC=5.5V,f I=
10Mhz,outputs open,one bit toggling-50%duty cycle
5.5mA Max V IN=5.3V or V IN=0.2V,OE= T/R=GND,V CC=5.5V,f I= 10Mhz,outputs open,one bit toggling-50%duty cycle
I CCD Dynamic I CC
(Note3)0.4mA/
MHz
Max
Outputs Open,OE=GND,T/R=
GND or V CC One Bit Toggling,
50%Duty Cycle
Note3:Guaranteed but not tested.
https://www.wendangku.net/doc/3c4612197.html,
3
AC Electrical Characteristics
Symbol
Parameter
54FCT
Units
Fig.No.
T A =?55?C to +125?C V CC =4.5V–5.5V
C L =50pF
Min
Max t PLH Propagation Delay 1.57.5ns Figure 4t PHL Data to Outputs 1.57.5t PZH Output Enable 1.510.0ns Figure 5t PZL Time
1.510.0t PHZ Output Disable 1.510.0ns Figure 5
t PLZ
Time
1.5
10.0
Capacitance
Symbol
Parameter
Max Units Conditions T A =25?C
C IN
Input Capacitance 10.0pF V CC =0V (OE ,T/R)C I/O (Note 4)
I/O Capacitance
12.0
pF
V CC =5.0V (A n ,B n )
Note 4:C I/O is measured at frequency f =1MHz,per MIL-STD-883B,Method 3012.
AC Loading
DS100950-6
*Includes jig and probe capacitance
FIGURE 1.Standard AC Test Load
DS100950-7
FIGURE 2.Test Input Signal Levels
Amplitude Rep.Rate t w t r t f 3.0V
1MHz
500ns
2.5ns
2.5ns
FIGURE 3.Test Input Signal Requirements
https://www.wendangku.net/doc/3c4612197.html, 4
AC Waveforms
DS100950-8
FIGURE 4.Propagation Delay Waveforms for Inverting and Non-Inverting Functions
DS100950-10
FIGURE 5.TRI-STATE Output HIGH and LOW Enable and Disable Times
https://www.wendangku.net/doc/3c4612197.html,
5
6
Physical Dimensions inches(millimeters)unless otherwise noted
20-Terminal Ceramic Chip Carrier(L)
NS Package Number E20A
20-Lead Ceramic Dual-In-Line Package(D)
NS Package Number J20A
7
https://www.wendangku.net/doc/3c4612197.html,
Physical Dimensions inches(millimeters)unless otherwise noted(Continued)
LIFE SUPPORT POLICY
NATIONAL’S PRODUCTS ARE NOT AUTHORIZED FOR USE AS CRITICAL COMPONENTS IN LIFE SUPPORT DE-VICES OR SYSTEMS WITHOUT THE EXPRESS WRITTEN APPROVAL OF THE PRESIDENT OF NATIONAL SEMI-CONDUCTOR CORPORATION.As used herein:
1.Life support devices or systems are devices or sys-
tems which,(a)are intended for surgical implant into
the body,or(b)support or sustain life,and whose fail-
ure to perform when properly used in accordance
with instructions for use provided in the labeling,can
be reasonably expected to result in a significant injury
to the user.
2.A critical component in any component of a life support
device or system whose failure to perform can be rea-
sonably expected to cause the failure of the life support
device or system,or to affect its safety or effectiveness.
National Semiconductor
Corporation
Americas
Tel:1-800-272-9959
Fax:1-800-737-7018
Email:support@https://www.wendangku.net/doc/3c4612197.html,
https://www.wendangku.net/doc/3c4612197.html,
National Semiconductor
Europe
Fax:+49(0)180-5308586
Email:europe.support@https://www.wendangku.net/doc/3c4612197.html,
Deutsch Tel:+49(0)180-5308585
English Tel:+49(0)180-5327832
Fran?ais Tel:+49(0)180-5329358
Italiano Tel:+49(0)180-5341680
National Semiconductor
Asia Pacific Customer
Response Group
Tel:65-2544466
Fax:65-2504466
Email:sea.support@https://www.wendangku.net/doc/3c4612197.html,
National Semiconductor
Japan Ltd.
Tel:81-3-5620-6175
Fax:81-3-5620-6179
20-Lead Ceramic Flatpak(F)
NS Package Number W20A
5
4
F
C
T
2
4
5
O
c
t
a
l
B
i
d
i
r
e
c
t
i
o
n
a
l
T
r
a
n
s
c
e
i
v
e
r
w
i
t
h
T
R
I
-
S
T
A
T
E
O
u
t
p
u
t
s
National does not assume any responsibility for use of any circuitry described,no circuit patent licenses are implied and National reserves the right at any time without notice to change said circuitry and specifications.