焊接用语中英对照
焊接专业英语词汇(熔化焊)
熔接fusion welding
压接pressure welding
焊接过程welding process
焊接技术welding technique
焊接工艺welding technology/procedure
焊接操作welding operation
焊接顺序welding sequence
焊接方向direction of welding
焊接位置welding position
熔敷顺序build-up sequence
deposition sequence
焊缝倾角weld slope/inclination of weld axis
焊缝转角weld rotation/angle of rotation
平焊位置flat position of welding
横焊位置horizontal position of welding
立焊位置vertical position of welding
仰焊位置overhead position of welding
平焊downhand welding/flat position welding
横焊horizontal position welding
立焊vertical position welding
仰焊overhead position welding
全位置焊all position welding:熔焊时,焊件接逢所处空间位置包括平焊、横焊、仰焊等位置所进行的焊接。如水平固定管所进行的环缝焊接
向下立焊vertical down welding/downward welding in the vertical position 向上立焊vertical up welding/upward welding in the vertical position 倾斜焊inclined position welding
上坡焊upward welding in the inclined position
下坡焊downward welding in the inclined position
对接焊butt welding
角焊fillet welding
搭接焊lap welding
船形焊fillet welding in the downhand position/fillet welding in the flat position
平角焊horizontal fillet welding
立角焊fillet welding in the vertical position
仰角焊fillet welding in the overhead position
坡口焊groove welding
I形坡口对接焊square butt welding
喇叭形坡口焊 flare groove welding
卷边焊flanged edge welding
纵缝焊接welding of l0ngitudinal seam
横缝焊接welding of transverse seam
环缝焊接girth welding/ circumferential
螺旋缝焊接welding of spiral seam/welding of helical seam 环缝对接焊butt welding of circumferential seam
定位焊tack welding
单面焊welding by one side
双面焊welding by both sides
单道焊single pass welding/single run welding
多道焊multi-pass welding
单层焊single layer welding
多层焊multi-layer welding
分段多层焊block sequence/ block welding
分层多道焊multi-layer and multi-pass welding
连续焊continuous welding
断续焊intermittent welding
打底焊backing weld
封底焊back sealing weld
盖面焊cosmetic welding
深熔焊deep penetration welding
摆动焊welding with weaving/weave bead welding
前倾焊 foreward welding (英国)/ forehand welding (美国) 后倾焊 backward welding(英国)/ backhand welding(美国)
分段退焊backstep welding
跳焊skip welding
对称焊balanced welding/ balanced welding sequence
左焊法leftward welding forehand welding
右焊法rightward welding/backhand welding
挑弧焊whipping method
自动焊automatic welding
手工焊manual welding/hand welding
车间焊接shop welding
工地焊接site welding(英国)/ field welding (美国)
拘束焊接restraint welding
堆焊surfacing/building up/overlaying
隔离层堆焊buttering
端部周边焊boxing/end return
返修焊rewelding
补焊repair welding
塞焊plug welding
槽焊slot welding
衬垫焊welding with backing
焊剂垫焊welding with flux backing
窄间隙焊narrow-gap welding
强制成形焊enclosed welding
脉冲电弧焊pulsed are welding
电弧点焊arc spot welding
螺柱焊stud welding
热风焊hot gas welding
高能焊high grade energy welding
固态焊接solid-state welding
单面焊双面成形one-side welding with back formation 焊接条件welding condition
焊接工艺参数welding parameter
极性polarity
正接electrode negative/straight polarity
反接electrode positive/reversed polarity
运条方式manipulation of electrode
焊接电流welding current
焊接电流增加时间welding current upslope time
焊接电流衰减时间welding current downslope time
电流密度current density
短路电流short circuit current
脉冲电流pulse level/pulse current level
脉冲电流幅值pulse current amplitude
基值电流background level
脉冲频率pulse frequency
脉冲焊接电流占空比duty cycle of pulse duration
电弧电压arc voltage
再引弧电压reignition voltage
焊接速度welding speed
行走速度rate of travel/travel speed
送丝速度wire feed rate
线能量heat input/energy input
热输入heat input
预热preheat
后热postheat
焊后热处理posweld heat treatment/postheat treatment 预热温度preheat temperature
层间温度interpass temperature
焊接终了温度finishing temperature
后热温度postheating temperature
焊丝伸出长度wire extension
弧长arc length
熔化速度melting rate
熔化时间melting time
熔化系数melting coefficient
熔敷速度rate of deposition/deposition rate
熔敷系数deposition coefficient
熔敷效率deposition efficiency
损失系数loss coefficient
飞spatter
飞溅率spatter loss coefficient
融合比fusion ratio
稀释dilution
稀释率rate of dilution
合金过度系数transfer efficiency/recovery (of an element)
坡口groove
坡口面groove face
坡口面角度angle of bevel (英国)/ bevel angle (美国)
坡口角度included angle(英国)/groove angle(美国)
坡口高度groove depth
钝边root face
钝边高度thickness of root face/width of root face
根部间隙root gap(英国)/root opening (美国)
根部半径root radius/groove radius
根部锐边root edge
卷边高度height of flange
卷边半径radius of flange
单面坡口single groove
双面坡口double groove
坡口形式groove type
I形坡口square groove
V形坡口single V groove
Y形坡口single V groove with root face
双Y形坡口double Vgroove with root face
带钝边U形坡口single U groove
带钝边双U形坡口double U groove
VY形坡口single compound angle groove
带钝边J形坡口single J groove
带钝边双J形坡口double J groove
单边V形坡口single bevel groove
双V形坡口double V groove
不对称双V形坡口 asymmetric double V groove
双单边V形坡口 double bevel groove/K groove
带垫板V形坡口 V groove with backing/ single V groove with backing 喇叭形坡口flare groove
锁底坡口single bevel groove with backing locked
坡形板边 tapered edge
焊缝 weld
接逢 seam
焊缝符号 welding symbol
焊缝金属 weld metal
填充金属 filler metal
熔敷金属 deposited metal
焊缝表面weld face/ face of weld
焊缝背面 back of weld
焊缝轴线axis of weld
焊缝尺寸 size of weld
焊缝宽度weld width/ width of weld
焊缝长度 weld length/ length of weld
焊缝有效长度 effective length of weld
焊缝厚度 throat depth/ throat thickness
焊缝计算厚度theoretical throat
焊缝实际厚度actual throat
熔深penetration/ depth of penetration
焊缝成形appearance of weld
焊缝成形系数form factor of weld
余高 reinforcement/ excess weld metal
背面余高root reinforcement
削平焊缝flush weld/ weld machined flush
对接焊缝butt weld
角焊缝fillet
焊脚leg/ fillet weld leg
角焊缝断面形状profile of fillet weld
平形角焊缝flat fillet
凸形角焊缝convex fillet weld
凹形角焊缝concave fillet weld
角焊缝凹度concavity
侧面角焊缝side fillet weld/ fillet weld in parallel shear 正面角焊缝front fillet weld/ fillet weld in normal shear 立角焊缝fillet weld in the vertical position
横角焊缝fillet weld in the horizontal position
平角焊缝fillet weld in the flat position
斜角焊缝oblique fillet weld
连续焊缝continuous weld
断续焊缝intermittent weld
连续角焊缝continuous fillet weld
断续角焊缝intermittent fillet weld
交错断续角焊缝staggered intermittent fillet weld
并列断续角焊缝chain intermittent fillet weld
端接焊缝edge weld
卷边焊缝flanged edge weld
塞焊焊缝plug weld
纵向焊缝l0ngitudinal weld
横向焊缝transverse weld
熔化焊
环行焊缝girth weld/ circumferential weld
螺旋形焊缝spiral weld/ helical weld
密封焊缝seal weld
承载焊缝strength weld
联系焊缝connective weld
定位焊缝tack weld
焊道bead/ run/ pass
焊波ripple
焊根weld root/ root of weld
焊趾weld toe/ toe
封底焊道sealing run (after making main weld)/ back weld
打底焊道backing weld (before making main weld)/ back weld
根部焊道root pass/ root run
填充焊道filling bead
盖面焊道cosmetic bead/ cover pass
回火焊道temper bead/ annealing bead
熔透焊道penetration bead
焊层 layer
焊接接头welded joint
接头形状joint geometry
等强匹配接头equalmatching weld joint
低强匹配接头undermatching weld joint
超强匹配接头overmatching weld joint
接头根部root of joint
对接接头butt joint
I形对接接头square butt joint
V形对接接头single V butt joint
U形对接接头single U butt joint
J形坡口接头single J butt joint
双V形对接接头double V butt joint
双单边V形对接接头double bevel butt joint/ K groove butt joint 带钝边U形对接接头double U butt joint
带钝边J形坡口接头double J joint
角接接头corner joint
T形接头T joint
斜T形接头inclined T joint
十字接头cruciform joint/ cross-shaped joint
三联接头joint among three members
搭接接头lap joint
套管接头muff joint/ sleeve joint
双盖板接头double strapped joint
盖板接头strapped joint
端接接头edge joint
卷边接头flanged edge joint
锁底对接接头lock butt joint
斜对接接头oblique butt joint
混合接头mixed joint/ composite joint
有间隙接头open joint
无间隙接头closed joint
焊接电弧welding arc
电弧形态arc shape
电弧物理行为arc physics behaviour
引弧striking arc
引弧电压striking voltage
电弧气氛arc atmosphere
阴极cathode
热阴极hot cathode
冷阴极cold cathode
阴极斑点cathode spot
阴极区cathode region
阴极区电场强度intensity of the electric field in the cathode region 阴极压降cathode drop
阳极anode
阳极斑点anode spot
斑点压力spot pressure
阳极区anode region
阳极区电场强度intensity of the electric field in the anode region 阳极压降anode drop
弧柱arc column/ arc stream
弧柱压降voltage drop in arc column
弧柱电位梯度potential gradient in the arc column
弧焰arc flame
弧心arc core
硬电弧forceful arc/ hard arc
软电弧soft arc
旋转电弧rotating arc
脉冲电弧pulsed arc
脉冲喷射电弧pulsed spray arc
起皱现象puckering phenomena
起皱电弧puckering arc
起皱临界电流 puckering critical current
间接电弧 indirect arc
压缩电弧 compressive arc
磁控电弧 magnetic controlling arc
电弧力 arc force
电磁力 electromagnectic force
电磁收缩效应 pinch effect
电弧飘移 wandering of arc
电弧稳定性 arc stability
电弧静特性 static characteristic of arc
电弧动特性 dynamic characteristic of arc
最小电压原理 principle of minimum voltage
电弧挺度arc stiffness
电弧偏吹 arc blow
磁偏吹 magnetic blow
阴极清理作用 cleaning action of the cathode
电弧自身调节 arc self-regulation
挖掘作用 digging action
极性效应 polarity effect
熔滴 droplet
熔滴比表面积 specific surface of droplet
熔滴过渡metal transfer
过度频率 transition frequency
粗滴过渡globular transfer; drop transfer
短路过渡short circuiting transfer
喷射过渡spray transfer
旋转喷射过渡 rotating spray transfer
脉冲喷射过渡 pulsed spray transfer
爆炸过渡 explosive transfer
渣壁过渡 flux wall guided transfer
熔池 molten pool
沸腾状熔池 boiling molten pool
弧坑crater
熔渣slag
渣系 slag system
渣系相图 slag system diagram
碱性渣 basic slag
酸性渣 acid slag
碱度 basicity
酸度 acidity
长渣 l0ng slag
短渣 short slag
粘性熔渣 viscous slag
氧化物型熔渣 oxide melting slag
盐型熔渣 salt melting slag
盐-氧化物型熔渣 salt-oxide melting slag
熔渣流动性 fluidity of the slag; slag fluidity 熔渣solidified slag
多孔焊渣 porous slag
玻璃状焊渣 vitreous slag
自动脱落焊渣 self-releasing slag
脱渣性 slag detachability
焊接设备 welding equipment; welding set
焊机 welding machine; welder
电焊机 electric welding machine; electric welder
焊接电源 welding power source
焊接热循环 weld thermal cycle
焊接温度场 field of weld temperature; weld temperature field 准稳定温度场 quasi-stationary temperature field
焊接热源 welding heat source
点热源 point heat source
线热源 linear heat source
面热源 plane heat source
瞬时集中热源 instantaneous concentration heat source
热效率 thermal efficiency
热能集中系数 coefficient of heat flow concentration
峰值温度 peak temperature
瞬时冷却速度 momentary cooling rate
冷却时间 cooling time
置换氧化 substitutionary oxydation
扩散氧化 diffusible oxydation
脱氧 desoxydation
先期脱氧 precedent desoxydation
扩散脱氧 diffusible desoxydation
沉淀脱氧 precipitation desoxydation
扩散氢 diffusible hydrogen
初始扩散氢 initial diffusible hydrogen
100℃残余扩散氢diffusible hydrogen remained at 100℃
残余氢 residual hydrogen
去氢 dehydrogenation
去氢热处理 heat treatment for dehydrogenation
脱硫 desulphurization
脱磷 dephosphorization
渗合金 alloying
微量合金化 microalloying
一次结晶组织 primary solidification structure
二次结晶组织 secondary solidification structure
联生结晶 epitaxial solidification
焊缝结晶形态 solidification mode in weld-bead
结晶层状线 ripple
多边化边界 polygonization boundary
结晶平均线速度 mean solidification rate
针状铁素体 acicular ferrite
条状铁素体 lath ferrite
侧板条铁素体 ferrite side-plate
晶界欣素体 grain boundary ferrite; polygonal ferrite; pro-entectoid ferrite
粒状贝氏体 granular bainite
板条马氏体 lath martensite
过热组织 overheated structure
魏氏组织 Widmannst?tten structure
M-A组元 martensite-austenite constituent
焊件失效分析 failure analysis of weldments
冷裂判据 criterion of cold cracking
冷裂敏感系数 cold cracking susceptibity coefficient
脆性温度区间 brittle temperature range
氢脆 hydrogen embrittlement
层状偏析 lamellar segregation
愈合 healing effect
断口金相fractography
断口 fracture
延性断口 ductile fracture
韧窝断口dimple fracture
脆性断口 brittle fracture
解理断口 cleavage fracture
准解理断口 quasi-cleavage fracture
氢致准解理断口 hydrogen-embrittlement induced
沿晶断口 intergranular fracture
穿晶断口 transgranular fracture
疲劳断口 fatigue fracture
滑移面断口 glide plane fracture
断口形貌 fracture apperance
断口试验 fracture test
宏观断口分析 macrofractography
放射区 radical zone
纤维区 fibrous zone
剪切唇区 shear lip aone
焊接性weldability
使用焊接性 service weldability
工艺焊接性 fabrication weldability
冶金焊接性 metallurgical weldability
热焊接性 thermal weldability
母材 base metal; parent metal
焊接区 weld zone
焊态 as-welded (AW)
母材熔化区 fusion zone
半熔化区 partial melting region
未混合区 unmixed zone
熔合区 bond area
熔合线 weld junction (英);bond line (美)
热影响区 heat-affected zone (HAZ)
过热区 overheated zone
粗晶区 coarse grained region
细晶区 fine grained region
过渡区 transition zone
硬化区 hardened zone
碳当量 carbon equivalent
铬当量 chromium equivalent
镍当量 nickel equivalent
舍夫勒组织图 Schaeffler's diagram
德龙组织图Del0ng’s diagram
连续冷却转变图(CCT图)continuous cooling transformation 裂纹敏感性 cracking sensibility
焊接裂纹 weld crack
焊缝裂纹 weld metal crack
焊道裂纹 bead crack
弧坑裂纹crater crack
热影响区裂纹 heat-affected zone crack
纵向裂纹 l0ngitudinal crack
横向裂纹 transverse crack
微裂纹 micro-crack; micro-fissure
热裂纹 hot crack
凝固裂纹 solidification crack
晶间裂纹 intercrystalline crack
穿晶裂纹 transcrystalline crack
多边化裂纹 polygonization crack
液化裂纹 liquation crack
失延裂纹 ductility-dip crack
冷裂纹 cold crack
延迟裂纹 delayed crack
氢致裂纹 hydrogen-induced crack
焊道下裂纹 underbead crack
焊根裂纹 root crack
焊趾裂纹 toe crack
锯齿形裂纹 chevron cracking
消除应力处理裂纹 stress relief annealing crack (SR crack) 再热裂纹 reheat crack
焊缝晶间腐蚀 weld intercryctalline corrosion
刀状腐蚀 knife line attack
敏化区腐蚀 weld decay
层状撕裂 lamellar tearing
焊接性试验 weldability
裂纹试验 cracking test
IIW裂纹试验 IIW cracking test
Y形坡口裂纹试验 slit type cracking test
分块形槽热裂纹试验 segmented circular groove cracking test
H形裂纹试验 H-type cracking test
鱼骨形裂纹试验 fishbone cracking test
指形裂纹试验 finger (cracking) test
T形裂纹试验 Tee type cracking test
环形槽裂纹试验 circular-groove cracking test
可调拘束裂纹试验 varestraint test
BWRA奥氏体钢裂纹试验 BWRA cracking test for austenitie steel
圆棒裂纹试验 bar type cracking test; round bar cracking test
里海裂纹试验 Lehigh restraint cracking test
圆形镶块裂纹试验 circular-path cracking test
十字接头裂纹试验 cruciform cracking test
Z向窗口拘束裂纹试验 Z-direction window type restraint cracking test G-BOP焊缝金属裂纹试验 G-BOP weld metal crack test
巴特尔焊道下裂纹试验 Battelle type underbead cracking test
U形拉伸试验 U-tension test
缪雷克期热裂纹试验 Murex hot cracking test
菲斯柯裂纹试验 FISCO (type) cracking test
CTS裂纹试验 controlled thermal severity
拉伸拘束裂纹试验(TRC试验)tensile restraint cracking test
刚性拘束裂纹试验(RRC试验)rigid restraint cracking test
插销试验 implant test
Tigamajig 薄板焊接裂纹试验 Tigamajing thin plate cracking test
焊道纵向弯曲试验 l0ngitudinal-bead test
柯麦雷尔弯曲试验 Kommerell bead bend test
肯泽尔弯曲试验 Kinzel test
缺口弯曲试验 notch bend test
热朔性试验 hot-ductility test
热影响区冲击试验 impact test of HAZ
热影响区模拟试验 synthetic heat-affected zone test
最高硬度试验 maximum hardness test
落锤试验 NRL (Naval Research Laboratory)
测氢试验 Hydrogen test
焊接材料
电极
焊接材料welding consumables
电极electrode
熔化电极consumable electrode
不熔化电极nonconsumable electrode
钨电极tungsten electrode
焊丝welding wire. Welding rod
实心焊丝solid wire
渡铜焊丝copper-plating welding wire
自保护焊丝self-shielded welding wire
药芯焊丝flux-cored wire
复合焊丝combined wire
堆焊焊丝surfacing welding rod
填充焊丝filler wire
焊条electrode/ covered electrode
焊芯core wire
药皮coating (of an electrode)/ covering (of an electrode)
涂料coating flux/coating material
造气剂gas forming constituents
造渣剂slag forming constituents
合金剂alloying constituent
脱氧剂dioxidizer
稳弧剂arc stabilizer
粘接剂binder
水玻璃water glass
水玻璃模数modules of water glass
酸性焊条acid electrode
高钛型焊条high titania (type) electrode
钛钙型焊条lime titania type electrode
钛铁矿形焊条ilmenite type electrode
氧化铁型焊条iron oxide type electrode/ high iron oxide type electrode 高纤维素型焊条high cellulose (type) electrode
石墨型焊条graphite type electrode
碱性焊条basic electrode/ lime type covered electrode
低氢型焊条low hydrogen type electrode
高韧性超低氢焊条high toughness super low hydrogen electrode
奥氏体焊条austenitic electrode
铁素体焊条ferritic electrode
不锈钢焊条stainless steel electrode
珠光体耐热钢焊条pearlitic heat resistant steel electrode
低温钢焊条low temperature steel electrode/ steel electrode for low temperature
铝合金焊条aluminum alloy arc welding electrode
铜合金焊条copper-alloy arc welding electrode
铜芯铸铁焊条cast iron electrode with steel core
纯镍铸铁焊条pure nickel cast iron electrode
球墨铸铁焊条electrode for welding spheroidal graphite cast iron
铸芯焊条electrode with cast core wire
镍基合金焊条nickel base alloy covered electrode
蒙乃尔焊条Monel electrode
纯铁焊条pure iron electrode
渗铝钢焊条alumetized steel electrode
高效率焊条high efficiency electrode
铁粉焊条iron powder electrode
焊接欠缺与检验
焊接欠缺welding imperfection
焊接缺陷weld defect
气孔blowhole/ gas pore
针尖状气孔pinhole
密集气孔porosity
条虫状气孔wormhole
裂纹crack
表面裂纹surface crack
咬边undercut
焊瘤overlap
凹坑pit
烧穿burn through
塌陷excessive penetration
未焊透incomplete penetration/ lack of penetration 未熔合lack of fusion/ incomplete fusion
未焊满incompletely filled weld
根部凹陷root concavity
电弧擦伤arc scratch
夹渣slag inclusion
夹杂物inclusion
夹钨tungsten inclusion
白点fish eye/ flake
错边misalignment/ dislocation
焊接检验
试件test piece
试样test specimen面弯试验face bend testing
背弯试验root bend test
侧弯试验side bend test
横弯试验horizontal bend test
纵弯试验axial bend test
压扁试验squeezing test
电阻焊摩擦焊爆炸焊扩散焊超声波焊等
电阻焊 resistance welding (RW)
点焊 spot welding; resistance spot welding
凸焊 projection welding
缝焊 seam welding
滚点焊 roll-spot welding
连续点焊 stitch welding
多点焊 multiple spot welding
手压点焊 push welding; poke welding
脉冲点焊 pulsation spot welding; multiple-impulse welding 双面点焊 direct spot welding
单面点焊 indirect spot welding
串联点焊 series spot welding
多点凸焊multiple projection welding
频道进缝焊 step-by-step seam welding
压平缝焊 mash seam welding
串联缝焊 series seam welding
对接缝焊 butt seam welding; foil-butt seam
电阻对焊 upset butt welding
闪光对焊 flash butt welding (FBW)
储能焊 stored energy welding
电容储能点焊 condenser discharge spot welding
高频电阻焊 high frequency resistance welding
冲击电阻焊 percussion welding
胶接点焊 spot weld-bonding; weld-bonding
闪光 flashing; flash
过梁 bridge; lintel
顶锻 upsetting; upset
夹紧力 clamping force
顶锻力 upsetting force; upset force
电极压力 electrode force; electrode pressure
电极滑移 electrode skid
焊接循环 welding cycle
预压时间 squeeze time
锻压时间 forge-delay time; forge time
焊接通电时间(电阻焊)welding time (resistance welding) 预热时间 preheat time
加热时间 heat time
冷却时间 cool time
间歇时间 quench time; chill time
回火时间 temper time
维持时间 hold time
休止时间 off time
闪光时间flash time; flashing time
顶锻时间 upset time; upsetting time
有电顶锻时间 upset current time
无电顶锻时间 upset current-off time
闪光速度 flashing speed
闪光电流 flashing current; flash current
顶锻电流 upset current
预热电流 preheat current
回火电流 temper current
调伸长度 initial overhange; extension
闪光留量 flash allowance
顶锻留量 upset allowance
顶锻速度 upset speed
电极接触面 electrode contact surface
贴合面 faying surface
焊点 welding spot
熔核 nugget
熔核直径 diameter of nugget
塑性金属环区corona bond
焊透率penetration rate
压痕indentation
压痕深度depth of indentation
压深率indentation ratio
翘离sheet separation
缩孔shrinkage cavity
胡须intrusion
电极粘损electrode pick up
喷溅splash/ expulsion
毛刺fin
飞边upset metal/ fin
焊点距weld spacing/ spot weld spacing
边距edge distance
分流shunt current
接触电阻contact resistance
电阻焊机resistance welding machine
点焊机spot welding machine
多点焊机multiple spot welding machine
移动式点焊机portable spot welding machine
缝焊机seam welding machine
纵横两用缝焊机universal seam welder
对焊机butt resistance welding machine
凸焊机projection welding machine
三相低频焊机three phase low frequency welder
二次整流电阻焊机direct current resistance welder secondary rectification
电容储能电阻焊机condenser discharge resistance welder
电容储能点焊机condenser type spot welder/ capacitor spot welding machine 工频电阻焊机mains frequency resistance welding machine
低频电阻焊机frequency converter resistance welding machine
高频焊机high frequency induction welder
逆变式电阻焊机inverter type resistance welding machine
全波阻焊电源full wave resistance welding power source
斩波阻焊电源chopped wave resistance welding power source
旋转焊接变压器rotary welding transformer
C形点焊钳C-type welding head/ C-type gun
X形点焊钳pincer spot welding head/ pliers spot welding head 断续器contactor
同步断续器synchronous contactor
异步断续器non-synchronous contactor
程序控制器sequencer
程序时间调节器sequencer timer
电极臂arm
电极握杆electrode holder
电极台板backup die/ bolster
电极水冷管electrode cooling tube
电极头electrode tip
电极帽electrode cap
锥头电极truncated tip electrode
平头电极flat tip electrode
尖头电极pointed tip electrode
球面电极radius tip electrode
偏心电极offest electrode
直电极straight electrode
弯电极cranked electrode
双弯电极double cranked (swannecked) electrode
滚轮电极circular electrode/ welding wheel
斜棱滚轮电极bevelled wheel
顶锻机构upsetting mechanism
电极总行程total electrode stroke
工作行程operational stroke
辅助行程electrode travel/ electrode stroke
臂间距离horn spacing/ throat opening
电极臂伸出长度arm extension
摩擦焊friction welding (FW)
转速friction speed
摩擦压力friction pressure/ heating pressure
摩擦时间friction time
摩擦变形量burn-off length
摩擦变形速度burn-off rate
停车时间stopping time
顶锻变形量forge length
顶锻变形速度forge rate
摩擦表面friction surface
储能摩擦焊fly-wheel type friction welding
径向摩擦焊radial friction welding
扩散焊diffusion welding (DW)
过渡液相扩散焊transient liquid phase diffusion welding 热等静压扩散焊hot isotatic pressure diffusion welding 热轧扩散焊roll diffusion welding
扩散缝焊seam diffusion welding
超塑成形扩散焊supperplastic forming diffusion bounding 隔离剂buttering material
爆炸焊explosive welding (EW)
爆炸点焊explosive spot welding
爆炸线焊explosive line welding
多层板爆炸焊explosive welding of multiplayer plates
多层管爆炸焊explosive welding of multiplayer tubes
覆板(覆管)cladding plat (tube)/ flyer plate (tube)
基板(基管)base plate(tube)/ parent plate (tube)
保护层buffer/ protector
基础base
预置角preset angle
间距initial stand-off/ spacing
装药量explosive load
装药密度charge density/ loading density
质量比mass ratio
平行法parallel plate configuration
角度法preset angle configuration
均匀布药average arranging explosive
梯形布药gradient arranging explosive
爆炸焊参数explosive welding parameters
初始参数initial parameters
动态参数dynamic parameters
界面参数interface parameters
爆轰速度detonation velocity
覆板速度cladding plate velocity
碰撞点impact point
碰撞点速度velocity of the impact point
弯折角bending angle
碰撞角collision angle
碰撞压力impact pressure
格尼能Gurney energy
垂直碰撞normal impact
倾斜碰撞oblique impact/ inclined impact
对称碰撞symmetrical impact
来流upper stream
出流down stream
再入射流re-entrant jet
自清理oneself cleaning
结合区bond zone
平面结合plane bond
波状结合wave-like bond
界面波长length of the interfacial wave
界面波幅amplitude of the interfacial wave
熔化层molten layer
熔化袋molten pocket
雷管区detonator zone
边界效应edge effect
焊接性窗口weldability windows
焊着率ratio of welding area
内爆法internal explosion process
外爆法external explosion process
半圆柱试验法semi-cylinder experiment method
超声波焊ultrasonic welding (UW)
超声波点焊ultrasonic spot welding
超声波缝焊ultrasonic seam welding
超声波点焊机ultrasonic spot welder
超声波缝焊机ultrasonic seam welder
冷压焊cold pressure welding (CPW)
热压焊hot pressure welding
热轧焊hot roll welding
旋弧压力焊rotating arc pressure welding
埋弧压力焊submerged arc pressure welding
电渣压力焊electroslag pressure welding
气压焊gas pressure welding
锻焊forge-welding/ blacksmith welding
磁力脉冲焊magnetic-pulse welding
焊接专业英语词汇(焊接卫生与安全)
焊接烟尘weld fume
焊接发尘量total amount of fumes
焊接烟尘浓度weld fume concentration
焊接烟尘容限浓度threshold limit values of weld fume (TLV)
焊接发尘速率weld fume emission rate
焊接有害气体welding toxic gases/ weld harmful gases
标定卫生空气需要量nominal hygienic air requirement
焊工尘肺pheumocomsis of welder
焊工锰中毒chronic occupational manganese poisoning of welder 焊工氟中毒fluorosis of welder
焊工金属烟热metal fume fever of welder
电光性眼炎eye-flash (arc eye)
电光性皮炎electro-photo dermatitis
电弧紫外线灼伤ultraviolet ray burn
防电击装置voltage reducing device 除尘装置dust collection device
焊工手套welding gloves
护脚welding spats
防护鞋shielding shoes
第一部分、计算机算法常用术语中英对照 Data Structures 基本数据结构 Dictionaries 字典 Priority Queues 堆 Graph Data Structures 图 Set Data Structures 集合 Kd-Trees 线段树 Numerical Problems 数值问题 Solving Linear Equations 线性方程组 Bandwidth Reduction 带宽压缩 Matrix Multiplication 矩阵乘法 Determinants and Permanents 行列式 Constrained and Unconstrained Optimization 最值问题Linear Programming 线性规划 Random Number Generation 随机数生成 Factoring and Primality Testing 因子分解/质数判定Arbitrary Precision Arithmetic 高精度计算Knapsack Problem 背包问题 Discrete Fourier Transform 离散Fourier变换Combinatorial Problems 组合问题 Sorting 排序
Searching 查找 Median and Selection 中位数 Generating Permutations 排列生成 Generating Subsets 子集生成 Generating Partitions 划分生成 Generating Graphs 图的生成 Calendrical Calculations 日期 Job Scheduling 工程安排 Satisfiability 可满足性 Graph Problems -- polynomial 图论-多项式算法Connected Components 连通分支 Topological Sorting 拓扑排序 Minimum Spanning Tree 最小生成树 Shortest Path 最短路径 Transitive Closure and Reduction 传递闭包Matching 匹配 Eulerian Cycle / Chinese Postman Euler回路/中国邮路Edge and Vertex Connectivity 割边/割点 Network Flow 网络流 Drawing Graphs Nicely 图的描绘 Drawing Trees 树的描绘 Planarity Detection and Embedding 平面性检测和嵌入
专业音频术语中英文对照 A AAC automatic ampltiude control 自动幅度控制 AB AB制立体声录音法?Abeyancd 暂停,潜态 A-B repeat A-B重复?ABS absolute 绝对得,完全得,绝对时间 ABSamerican bureau ofstanda rd 美国标准局?ABSS autoblank secrion scanning 自动磁带空白部分扫描Absti me绝对运行时间?A、DEF audio defeat音频降噪,噪声抑制,伴音静噪 ADJ adj ective 附属得,附件?ADJ Adjust 调节 ADJ acousticdelay line声延迟线 Admission 允许进入,供给 ADP acousticdata processor音响数据处理机 ADP(T) adapter 延配器,转接器ADRES automaticdynamic range expansion system?动态范围扩展系统 A DRM analog todigital remaster 模拟录音、数字处理数码唱盘 ADS audio distribution system 音频分配系统 A、DUB audio dubbing配音,音频复制,后期录音 ADV advance 送入,提升,前置量?ADV adversum对抗 ADV advance r 相位超前补偿器?Adventure惊险效果 AE audio erasing 音频(声音)擦除 AE auxiliary equipment 辅助设备Aerial天线 AESaudio engineering society美国声频工程协会AF audio fidelity 音频保真度?AF audio frequency音频频率 AFC active field control自动频率控制?AFC automaticfrequency control 声场控制 Affricate 塞擦音?AFL aside fade listen 衰减后(推子后)监听 A-fader 音频衰减 AFM advance frequency modulation 高级调频 AFS acoustic feedback spea ker 声反馈扬声器 AFT automatic fine tuning 自动微调 AFTAAS advancedfast time acousti canalysis system?高级快速音响分析系统 After 转移部分文件 Afterglow余辉,夕照时分音响效果 Again st 以……为背景 AGC automatic gain control 自动增益控制AHDaudiohigh density音频高密度唱片系统 AI advanced integrated预汇流AI amplifier input 放大器输入 AI artificial intelligence 人工智能AI azimuth indi cator 方位指示器 A-IN 音频输入 A-INSEL audio input selection 音频输入选择 Alarm 警报器 ALC automatic level control自动电平控制?ALC automatic load control自动负载控制
机械——焊接专业术语中英文对照 (郭运)整理 1Single 单面的 2V—groove V型坡口 3Joint 焊接接头 4Edges overlap 接头形式 5Butt 对接 6T T型焊接 7Fillet 角焊缝 8Edge 端接 9Corner 角接 10Radius 半径 11Joint root 焊接根部 12Bevel angle 削边角度 13Groove angle 坡口角度 14Root face 根部钝边 15Groove face 坡口面 16Plug weld 塞焊 17Spot weld 点焊 18Seam weld 缝焊 19Slot weld 槽焊 20Double—flare—bevel—groove K型坡口焊缝
21Single—flare—V 单面V型22Edge flange 翻边端接 23Corner flange 卷边端接 24Flange weld 卷边焊缝25Flare weld 扩口焊缝26Fillet weld 角焊缝 27Slot weld 槽焊缝 28Spot weld 点焊缝 29Surfacing weld 堆焊焊缝30Melt—through weld 熔透焊缝31Backing weld 打底焊缝32Back weld 背面焊缝33Root weld 根部焊缝34Crown weld 隆起部分35Weld reinforcement 焊缝加强36Weld face 焊缝表面37Cap pass 盖面焊道38Weld edge 焊缝边缘39Leg 焊脚 40Toe 焊趾 41Buildup 堆焊 42Weld reinforcement 焊缝加强高
信号与系统常用词汇中英文对照表 序号英文词汇中文翻译 1 Absolutely summable impulse response 绝对可和的冲激响应 2 Absolutely integrable impulse response 绝对积的冲激响应 3 Accumulation property 累加性质 4 Adder 加法器 5 Additivity 可加性 6 Aliasing 混叠 7 Allpass system 全通系统 8 Amplitude Modulation(AM) 幅度调制 9 Amplifier 放大器 10 Analog-to-Digital Conversion 模数转换 11 Analysis equation 分析方程 12 Aperiodic signal 非周期性信号 13 Associative property 结合性质 14 Audio system 音频系统 15 Autocorrelation function 自相关函数 16 Band-limited signal 带限信号 17 Band-limited interpolation 带限内插 18 Bandpass filter 带通滤波器 19 Bandpass-sampling technique 带通抽样方法 20 Bandpass signal 带通信号 21 Bandwidth of an LTI system 线性时不变系统的带宽 22 Bilinear transformation 双线性变换 23 Block diagram 方框图 24 Bode plot 波特图 25 Butterworth filter 巴特沃斯滤波器 26 Carrier frequency 载波频率 27 Carrier signal 载波信号 28 Cartesian (rectangular) form for complex number 复数的笛卡尔(直角坐标)形式 29 Cascade-form block diagram 级联型方框图 30 Cascade (series) interconnection 级联连接 31 Causal LTI system 因果的线性时不变系统 32 Channel equalization 信道均衡 33 """Chirp"" transform algorithm" 线性调频变换算法 34 Closed-loop system 闭环系统 35 Coefficient multiplier 系数乘法器 36 Communication system 通信系统 37 Commutative property 交换性质 38 Complex conjugate 复共轭 39 Complex exponential 复指数 40 Complex number 复数 41 Continuous-time signal 连续时间信号 42 Conjugate symmetry 共轭对称性
鞋业(类)常用术语中英文对照 ---欧维思品牌鞋业折扣店 --https://www.wendangku.net/doc/386124574.html, 目录 第一章:Stage 阶段………………………………P2-P10 第二章技术……………………………P7-P15 第三章鞋型转移……………………………P16-P17 欧维思品牌鞋业折扣店招商加盟网--https://www.wendangku.net/doc/386124574.html,- 1 -
第一章:Stage 阶段 ----欧维思品牌鞋业折扣店https://www.wendangku.net/doc/386124574.html, I.3.1. Two main sections in Dev. Division 开发的两大部分: 1. Development section: explain more in process of new models to make samples in order to introduce market to achieve qty. 开发部分:此部分着重于新型体的样品制作,以便可介绍给客户来争取一定数量的订单。 https://www.wendangku.net/doc/386124574.html,mercialization section: explain more in process of technical after it was developed with Fitting test and Wear test to ensure that all products meet consumers’ expectations in terms of Fitting, Comfort and Performance. 技术部分:开发转移到技术部门,此阶段着重于在开发阶段完成试穿测试, 确保产品在试穿/舒适/功能方面可满足客户的要求后进行的技术工作。 I.3.2. Development Stages 开发阶段 I.3.2.1. PPR: Pre Prototype Review 初始线条评估 1st stage to review all sample products Internally by customer ( Marketing,designer,L.O) For performance shoes, we have Fitting and Wear Test Sample to be sent. * The topics of review are : 1. Material 2. Quality 3. Performance 4. Price 5. Color 6. Design 7. Forecast 客人内部(市场销售、设计师、本地客人)对于新鞋型第一阶段之评估。 对于功能性鞋型,我们要寄Fitting test &Wear test试穿样品。 此时检查要点如下: 1、材料 2、品质 3、功能 4、价格 5、颜色 6、设计 7、订单预测 I.3.2.2. PFR:Prototype Final Review 最后线条评估 Final stage to review all sample shoes before introducing the products to the customers. At this time, all key points should be finally decided (Pattern / Design, Color,Price, Material (should be released), etc.). The result of Fitting Test should be considered for PPR meeting as a basic. 在全部新鞋型介绍给客户前之最后检查阶段,此时所有要点均需做出最后确定,如:纸版、设计、颜色、价位、材料(必须是通过了测试)等等。 寄出试样鞋时需附上试穿报告。此时的试穿结果是PPR 会议之基本考量点。 I.3.2.3. SMS1:Salesman Sample 1 销样一 欧维思品牌鞋业折扣店招商加盟网--https://www.wendangku.net/doc/386124574.html,- 2 -
第一部分计算机算法常用术语中英对照 Data Structures 基本数据结构Dictionaries 字典Priority Queues 堆Graph Data Structures 图Set Data Structures 集合Kd-Trees 线段树Numerical Problems 数值问题Solving Linear Equations 线性方程组Fourier变换Bandwidth Reduction 带宽压缩Matrix Multiplication 矩阵乘法Satisfiability 可满足性Determinants and Permanents 行列式Linear Programming 线性规划Matching 匹配Constrained and Unconstrained Optimization 最值问题Clique 最大团Cryptography 密码Random Number Generation 随机数生成Shortest Path 最短路径recursion递归Factoring and Primality Testing 因子分解/质数判定Searching 查找Sorting 排序Arbitrary Precision Arithmetic 高精度计算Calendrical Calculations 日期 Discrete Fourier Transform 离散Combinatorial Problems 组合问题 Median and Selection 中位数Generating Permutations 排列生成 Generating Subsets 子集生成Generating Partitions 划分生成 Generating Graphs 图的生成Job Scheduling 工程安排 Graph Problems -- polynomial 图论-多项式算法Connected Components 连通分支Topological Sorting 拓扑排序Minimum Spanning Tree 最小生成树Transitive Closure and Reduction 传递闭包Network Flow 网络流 Eulerian Cycle / Chinese Postman Euler回路/中国邮路 Edge and Vertex Connectivity 割边/割点Independent Set 独立集 Drawing Graphs Nicely 图的描绘Drawing Trees 树的描绘 Planarity Detection and Embedding 平面性检测和嵌入Vertex Cover 点覆盖 Graph Problems -- hard 图论-NP问题Traveling Salesman Problem 旅行商问题Hamiltonian Cycle Hamilton回路Graph Partition 图的划分 Vertex Coloring 点染色Edge Coloring 边染色 Graph Isomorphism 同构Steiner Tree Steiner树 Feedback Edge/Vertex Set 最大无环子图Computational Geometry 计算几何 Convex Hull 凸包Triangulation 三角剖分 V oronoi Diagrams V oronoi图Nearest Neighbor Search 最近点对查询Range Search 范围查询Point Location 位置查询 Intersection Detection 碰撞测试Bin Packing 装箱问题 Medial-Axis Transformation 中轴变换Polygon Partitioning 多边形分割Simplifying Polygons 多边形化简Shape Similarity 相似多边形 Motion Planning 运动规划Maintaining Line Arrangements 平面分割Minkowski Sum Minkowski和Set and String Problems 集合与串的问题 Set Cover 集合覆盖Set Packing 集合配置 Approximate String Matching 模糊匹配Text Compression 压缩 DP—Dynamic Programming动态规划Longest Common Substring 最长公共子串Shortest Common Superstring 最短公共父串String Matching 模式匹配 Finite State Machine Minimization 有穷自动机简化
1、the airframe 机身,结构 2、The front (fore) part 前部 3、The rear (aft) part 后部 4、port 左旋(舵) 5、starboard 右旋(舵) 6、the inboard engine or inboards 内侧发动机 7、the outboard engine or outboards 外侧发动机 8、the nose 机头 9、the belly 腹部 10、the skin 蒙皮 11、the windscreen or windshield 风挡 12、the wing 机翼 13、the trailing edge 机翼后缘 14、the leading edge 机翼前缘 15、the wing tip 翼尖 16、the control surface 操纵面 17、ailerons 副翼 18、flaps (inboard flap,outboard flap,leading edge flaps) 襟翼(内侧襟翼,外侧襟翼,前缘缝翼) 19、spoilers (inboard\outboard spoiler)(spoiler down\up) 阻力板,扰流板(内、外侧扰流板)(扰流板放下、打开) 20、slats 缝翼 21、elevators (elevator control tab) 升降舵(升降舵操纵片) 22、rudder (rudder control tab) 方向舵(方向舵操纵片)
23、flap angle 襟翼角 24、flap setting 襟翼调整 25、the full flap position 全襟翼位置 26、a flapless landing 无襟翼着陆 27、the landing gear 起落架 28、stabilizer 安定面 29、the nose wheel 前轮 30、gear locked 起落架锁定 31、the wheel well 起落架舱 32、the wheel door 起落架舱门 33、a tyre 轮胎 34、to burst 爆破 35、a deflated tyre 放了气的轮胎 36、a flat tyre 走了气的轮胎 37、a puncture 轮胎被扎破 38、to extend the flaps (to retract the flaps) 放下襟翼(收上襟翼) 39、gear extention (gear retraction) 起落架放下(起落架收上) 40、The gear is jammed. 起落架被卡死。 41、The flaps are jammed. 襟翼被卡死。 42、the emergency extention system 应急放下系统 43、to crank the gear down 摆动放下起落架 44、the brakes 刹车
熟练掌握名目繁多金融术语除了是专业人士的必修课外,在金融渗透、人人参与投资的时代,了解一些常用的金融术语也对普通投资者们大有益处。本文就为你详细列举了一些常用的可中英文对照的金融术语,帮助你了解生活中的金融。 金融 资产组合(Portfolio):指投资者持有的一组资产。一个资产多元化的投资组合 通常会包含股票、债券、货币市场资产、现金以及实物资产如黄金等。 证券投资(Portfolio Investment) :国际收支中、资本帐下的一个项目,反映资 本跨国进行证券投资的情况,与直接投资不同,后者涉及在国外设立公司开展业务,直接参与公司的经营管理。证券投资则一般只是被动地持有股票或债券。 投资组合经理(Portfolio Manager):替投资者管理资产组合的人,通常获授权 在约定规范下自由运用资金。共同基金的投资组合经理负责执行投资策略,将资金投资在各类资产上。 头寸(Positio n):就证券投资而言,头寸是指在一项资产上做多(即拥有)或做空(即借入待还)的数量。 总资产收益率(ROTA):资产收益率是企业净利润与平均资产总额地百分比,也 叫资产回报率(ROA),它是用来衡量每单位资产创造多少净利润的指标。其计 算公式为:资产收益率二净利润/平均资产总额X 100% ;该指标越高,表明企业 资产利用效果越好,说明企业在增加收入和节约资金使用等方面取得了良好的效果,否则相反。 整批交易(Round Lot Trade):指按证券和商品在市场最普遍的交易单位(例如 100股为一单位)进行的交易。 交易回合(Round Turn):指在同一市场上通过对两种证券或合约一买一卖,或 一卖一买的交易两相抵消。通常在计算手续费时会提及交易回合。
常用焊接术语中英文对照 焊接Welding 10.1 焊接种类Varieties of Welding 电弧焊arc welding 电熔焊electric fusion welding (EFW) 气熔焊fusion gas welding (FGW) 电阻焊electric resistance welding (ERW) 有保护的金属电弧焊shielded metal arc welding (SMAW) 手工或自动隋性气体保护钨极电弧焊manual and automatic inert gas tungsten arc welding (GTAW) 自动埋弧焊automatic submerged arc welding 金属极隋性气体保护电弧焊gas metal arc weiding (GMAW) 氩弧焊argon-arc welding, 气体保护电弧焊gas-shielded arc welding 气焊gas welding; flame welding 等离子焊plasma welding 硬钎焊braze welding 电渣焊electroslag welding 爆炸焊explosive welding 10.2 焊接形式Type of Welding
角焊fillet welding 间断焊intermittent welding 点焊spot welding 对焊butt welding 搭焊lap welding 塞焊plug welding 珠焊bead welding 槽焊slot welding 堆焊build up welding 垫板焊backing weld 坡口groove V形坡口V groove 单面U形坡口single U groove K形坡口double bevel groove X形坡口double V groove 双面U形坡口double U groove U-V组合坡口combination U and V groove 根部间隙root gap 焊接符号symbol of weld 错边量alignment tolerance 10.3 焊接位置Welding Position 仰焊overhead welding 现场焊field weld (F.W.)
房务部:Rooms Division 前厅部:Front Office 客房部:Housekeeping 大堂副理:Assistant Manager 宾客关系主任:Guest Relation Officer 前台:Front Desk 接待处:Reception/Check-in 收银处:Cashier/Check-out 领班:Captain 主管:Supervisor 班次负责人:Shift Leader 商务中心:Business Center 客房服务代表:Guest service agent(接待和收银合并之后的前台人员的称呼)简称GSA 电话总机:Switch Board 接线员:Operator 预订处:Room Reservation 礼宾服务处:Concierge 大厅服务处:Bell Service 金钥匙:Golden Key 行政楼层:Executive Floor 行政酒廊:Executive Lounge 行李生:Bellman 迎宾员:Doorman 夜审:End of Day /Night auditor 2.前厅服务项目专业术语介绍 入住:Check-in 退房:Check-out 外币兑换:Foreign Currency Exchange 问询:Information 接送机服务:Pick up service 叫醒服务:Wake up call 请勿打扰服务:DND Do not disturbed 失物招领:Lost and Found 国内直拨和国际直拨电话:DDD and IDD Domestic Direct Dial and International Direct Dial对方付费电话:Collect Call 3.前厅常用物品术语介绍: 住宿登记单:Registration card 欢迎卡:Welcome card 订房凭证:Voucher 交接本:log book 信封:Envelope 房卡钥匙:Room key 安全保管箱:Safe Deposit Box 客房统计和出售率统计的术语 预离房:Expected Departure 预抵房:Expected Arrival
AW——ARC WELDING——电弧焊 AHW——atomic hydrogen welding——原子氢焊 BMAW——bare metal arc welding——无保护金属丝电弧焊 CAW——carbon arc welding——碳弧焊 CAW-G——gas carbon arc welding——气保护碳弧焊 CAW-S——shielded carbon arc welding——有保护碳弧焊 CAW-T——twin carbon arc welding——双碳极间电弧焊 EGW——electrogas welding——气电立焊 FCAW——flux cored arc welding——药芯焊丝电弧焊 FCW-G——gas-shielded flux cored arc welding——气保护药芯焊丝电弧焊 FCW-S——self-shielded flux cored arc welding——自保护药芯焊丝电弧焊 GMAW——gas metal arc welding——熔化极气体保护电弧焊 GMAW-P——pulsed arc——熔化极气体保护脉冲电弧焊 GMAW-S——short circuiting arc——熔化极气体保护短路过度电弧焊 GTAW——gas tungsten arc welding——钨极气体保护电弧焊 GTAW-P——pulsed arc——钨极气体保护脉冲电弧焊 MIAW——magnetically impelled arc welding——磁推力电弧焊 PAW——plasma arc welding——等离子弧焊 SMAW——shielded metal arc welding——焊条电弧焊 SW——stud arc welding——螺栓电弧焊 SAW——submerged arc welding——埋弧焊
Aspen Plus常用词汇中英文对照表 A adiabatic 绝热的 adsorption 吸附 aircooler 空冷器 algorithm 算法 alias 又名,别名 align 使……排成直线 ambient temperature 环境温度 analysis 分析 annotation 注释 apparent component approach 表观组分方法approach 方法 aqueous 水溶液的,水的,含水的 assay化验(油品分析) ADA (assay data analysis)化验数据分析assign 指定 attach连接 attr-comps 组分属性 attr-scaling属性标量 available可用的 B backup (降液管内的清液层)高度 baffles 挡板 balance 平衡模块,平衡 base components 基准组分 base method 基本方法(包含了常见物性方法)batch 批量处理,一批 BatchFrac 间歇精馏 binary interaction 二元交互作用 blank simulation 空白模拟 block模块 Block-Var 模块变量boilup ratio 再沸比 bottoms rate 塔底产品流率 bottoms to feed ratio塔底产品流率与进料流率比brake power 轴功率 Broyden 布洛伊顿拟牛顿法 built-in 内置 C calculator 计算器 capacity 通量 capacity factor 通量负荷因子 cascade 层叠 case study 工况分析 category 类别,种类 chemical equilibrium 化学平衡 Chem-Var 化学变量 class分类 clearance 间隙 co-current 并流 coefficient 系数 column 塔 CGCCs (column grand composite curves)塔的总组合曲线 column specifications 塔设定 Compattr-Var 组分变量 component 组分 composition 组成 Compr 压缩机或涡轮机模块 comps-groups 组分分组 conceptual design 概念设计 condenser 冷凝器 condenser specification 冷凝器设定 configuration 配置
一.电气名词 Electric items 二.线路(母线、回路)Lines (Bus , circuits) 三.设备 Equipments 四.保护、继电器 Protection , relays 五.电气仪表 Electric instruments 六.防雷 Lightning protection 七.接地 Grounding , earthing 八.室、所 Room , Substation 九.电修车间设备 Equipments of electric repair 十.材料 Material 十一.图名 Drawings , diagrams 十二.表头 Tables 十三.标准图词汇 Terms from standard DWG 一.电气名词 Electric items 交(直)流 Alternating (direct) current 短路电流 Short-circuit current 起始次暂态短路电流 Initial subtransient short-circuit current 冲击电流 Impulse current 稳态短路电流 Steady state short-circuit current 临界电流 Critical current 切断电流 Rupturing current 熔断电流 Blow-out current 故障电流 Fault current 计算电流 Calculating current 极限有限电流 Limit effective current 过电流 Over current 逆电流 Inverse current 整定电流 Setting current 额定电流 Rated current 电流密度 Current density 短路电流最大有效值 Maximum effective value of short-circuit current 高压 High-voltage , High-tension 低压 Low-voltage , Low-tension 计算电压 Calculating voltage 激磁电压 Exciting voltage 冲击电压 Impulse voltage 临界电压 Critical voltage 残留电压 Residual voltage 击穿电压 Puncture voltage 脉动电压 Pulsating voltage 供电电压 Supply voltage 电力电压 Power voltage
常用保险术语 保险费率 premium rate 单位保险金额应该收取的保险费。 损失 loss 非故意的、非预期的和非计划的经济价值的减少或灭失。通常分为直接损失和间接损失。 损失程度 loss severity 保险标的可能遭受的损失的严重程度。 直接损失 direct loss 由风险事故导致的财产本身的损失。 间接损失 indirect loss 由直接损失引起的额外费用损失、收入损失和责任损失等无形损失。 保险 insurance 投保人根据合同约定,向保险人支付保险费,保险人对于合同约定的可能发生的事故因其发生所造成的财产损失承担赔偿保险金责任,或者当被保险人死亡、伤残、疾病或者达到合同约定的年龄、期限时承担给付保险金责任的商业保险行为。 财产保险 property insurance 以财产及其有关利益为保险标的的保险。 企业财产保险 commercial property insurance 以单位、团体所有或占有的在指定地点的财产及其有关利益为保险标的的财产保险。 营业中断保险 business interruption insurance 以单位因停产、停业或经营受影响而面临的预期利润的减少及必要的费用支出为保险标的的财产保险。 机器损坏保险 machinery breakdown insurance 以各类已安装完毕并投入运行的机器为保险标的财产保险。 货物运输保险 cargo insurance 以运输途中的货物为保险标的保险。 海上货物运输保险 ocean marine cargo insurance 以通过海上运输方式运输的货物作为保险标的的保险。 陆上货物运输保险 inland transit insurance 以通过陆上运输方式运输的货物为保险标的的保险。
焊接专业术语中英对照焊接欠缺与检验 焊接欠缺welding imperfection 焊接缺陷weld defect 气孔blowhole/ gas pore 针尖状气孔pinhole 密集气孔porosity 条虫状气孔wormhole 裂纹crack 表面裂纹surface crack 咬边undercut 焊瘤overlap 凹坑pit 烧穿burn through 塌陷excessive penetration 未焊透incomplete penetration/ lack of penetration 未熔合lack of fusion/ incomplete fusion 未焊满incompletely filled weld 根部凹陷root concavity 电弧擦伤arc scratch 夹渣slag inclusion 夹杂物inclusion 夹钨tungsten inclusion 白点fish eye/ flake 错边misalignment/ dislocation 焊接检验 试件test piece 试样test specimen 无损检验nondestructive test 破坏检验destructive test 外观检查visual examination 超声波探伤ultrasonic inspection 直射法超声波探伤straight beam method 斜射法超声波探伤angle beam method 液浸法超声波探伤immersion method 射线探伤radiographic inspection/ radiography X射线探伤X-ray radiographic inspection γ射线探伤gamma-ray inspection X射线工业电视探伤X-ray industrial television inspection 磁粉探伤magnetic particle inspection 电磁探伤electromagnetic inspection/ eddy current test 探伤灵敏度flaw detection sensitivity 渗透探伤penetration inspection 荧光探伤flurescent penetrant inspection 着色探伤dye penetrant inspection 密封性检验leak test 气密性检验air tight test 枕形气密检验pillow test 耐压检验pressure test 水压检验hydraulic test 气压检验pneumatic test 液晶检验liquid crystal test 声发射检测acoustic emission testing 面弯试验face bend testing 背弯试验root bend test 侧弯试验side bend test 横弯试验horizontal bend test 纵弯试验axial bend test 压扁试验squeezing test actual weld-throat thick-ness焊缝厚度 all-around weld整周焊缝 all-around weld (整周焊缝)环焊缝 angle butt weld斜对接焊 angle weld角焊 appearance of weld焊缝成形 arc-seam weld电弧缝焊 arc-spot weld电弧点焊 arc-weld电弧焊 aspect ratio of weld焊缝成形系数 at weld edge在焊缝边上 attachment weld连接焊缝 automatic spot weld自动点焊法 automatic weld自动焊接 axis of a weld焊缝行南? 焊接轴线 axis of weld焊缝轴线; 焊接轴线 back of weld焊缝背面 backing groove of weld焊缝反面坡口backing weld底焊; 底焊焊缝 bare metal arc weld裸焊条电弧焊 bead weld珠焊; 堆焊 bead-on-plate weld堆焊焊缝 beading weld凸焊 beam-to-beam weld梁间焊接; 梁式引线焊接block sequence weld分段多层焊 bond weld钢轨接头焊接 bridge seam weld桥缝焊接; 桥线焊 brize weld硬焊 butt weld对接焊缝 butt weld ends对头焊接端 butt-weld碰焊; 平式焊接; 对头焊接 butt-weld in the downhand position对接平焊
电影专业术语中英文对照 A Above-the-line 线上费用 A-B roll A-B卷 AC 交流电 Academy ratio 学院标准画框比 Adaptation 改编 ADR editor ADR 剪辑师 Aligator clamp=gaffer grip 固定灯具的弹簧夹,又称鳄鱼夹 Ambient Sounds 环境音 Amp 安培 Amplification 信号放大 Amplitude 振幅 Analog 模拟 Anamorphic lens 变形镜头 Aperture 光圈 Answer Print 校正拷贝 Arc 摄像机的弧度运动 Art director 艺术指导 Aspect ratio 画框比 Atmosphere sound 气氛音 Attack 起音 Audio board 调音台 Audio mixer 混音器,混音师 Automatic dialogue replacement 自动对白补录 Automatic focus 自动对焦 Automatic gain control 自动增益控制 Automatic iris 自动光圈(少用) Axis of action 表演轴线 B Back light 轮廓光 Background light=Scenery light 场景光 Balance 平衡 Balanced 平衡电缆 Barndoor 遮扉(灯具上的黑色金属活动板,遮光用的) Barney 隔音套 Base 片基(用来附着感光乳剂的胶片基底) Base plate 底座(固定灯的) Baselight level 基本亮度 Batch capturing 批次采集 Below-the-line 线下费用 Bidirectional 双向麦克风 Bit depth 位元深度(在数字声音中每次取样的数目,通常是8,12,16)