广域网协议设置
刷钻代码 https://www.wendangku.net/doc/403482468.html,/
一、HDLC
HDLC是CISCO路由器使用的缺省协议,一台新路由器在HDLC环境中使用时不需要设置广域网协议。
1.有关命令
端口设置
设置HDLC封装 encapsulation hdlc
设置DCE端线路速度
clockrate speed
2.举例
Router1:
Interface Serial0
-- ip address 192.200.10.1 255.255.255.0
-- Clockrate 1000000
Router2:
-- interface Serial0
-- ip address 192.200.10.2 255.255.255.0
二、X.25
1.有关命令
端口设置
设置X.25封装encapsulation x25[dce]
设置X.121地址x25 address x.121-address
设置远方站点的地址映射x25 map ip IP address
x.121-address
2.举例
Router1:
interface Serial0
-- encapsulation x25
-- ip address 192.200.10.1 255.255.255.0
-- x25 address 110101
-- x25 map ip 192.200.10.2 110102
Router2:
interface Serial0
-- encapsulation x25
-- ip address 192.200.10.2 255.255.255.0
-- x25 address 110102
-- x25 map ip 192.200.10.1 110101
三、Frame Relay
1.有关命令
端口设置
设置FR封装 encapsulation frame-relay
设置FR LMI类型
子端口设置 frame-relay lmi-type {ansi|cisco|q933a}设置FR DLCI编号frame-relay interface-dlci
dlci[broadcast]
2.举例
Router1:
interface Serial0
-- encapsulation frame-relay
-- frame-relay lmi-type ansi
interface Serial0.16 point-to-point
-- ip address 192.200.10.1 255.255.255.0
-- frame-relay interfac dlci 16
Router2:
interfacte Serial0
-- encapsulation frame-relay
-- frame-relay lmi-type ansi
interface Serial0.17 point-to-point
-- ip address 192.200.10.2 255.255.255.0
-- frame-relay interface-dlci 17
四、PSTN
电话网络(PSTN)是目前普及程度最高、成本最低的公用通讯网络,它在网络互连中也有广泛的应用。电话网络的应用一般可分为两种类型,一种是同等级别机构之间以按需拨号(DDR)的方式实现互连,一种是ISP为拨号上网的用户提供的服务。这两种类型使用的设置命令大致相同,但在设置思想上又有重要的差别。
2.相关命令
全局设置:
设置PPP安全协议使用户名和密码 username username password password
设置路由器与modem的接口指令 chat-script script-name EXPECT SEND EXPECT SEND(etc.)
设置用户的IP地址池 ip local pool {default|pool-name low-ip-address [high-ip-address]}
指定地址池的工作方式 ip address-pool [dhcp-proxy-client|local]
指定DHCP服务器 ip dhcp-server [ip-address|name]指定TACACS服务器 tacacs-server host hostname [single-connection] [port interger] [timeout integer] [key string]
异步口(async)设置:
设置封装形式为PPP encapsulation PPP
启动异步口的路由功能 async default routing
设置异步口的PPP工作方式 async mode {dedicated interactive}
启动按需拨号功能 dialer in-band
设置用户的IP地址 peer default ip address {ip-address|dhcp|pool [pool-name]}
设置IP地址与Ethernet0相同 ip unnumbered
Ehternet0
启动TCP头压缩 ip tcp header-compression passive 设置端口在挂断前的等待时间 dialer idle-timeout seconds
设置IP地址与电话号码的映射 dialer map ip next-hop-address dialer-string
设置PPP安全协议 ppp authentication protocol
line拨号线设置:
指定特定情况下路由器使用的chat-script script {dialer|reset} script-name
设置modem的工作方式 modem {inout|dialin}
自动配置modem类型modem autoconfig discovery
设置拨号线的通讯速率 speed speed
设置通讯线路的流控方式 flowcontrol hardware
连通后自动执行命令autocommand command
2.DDR实例
北京:
-- username guangzhou password Legend
-- (password必须与广州的路由器设置的password一样)
-- chat-script
rstmdm"""AT&FS0=1&B1&C1&D2&H1&K1&M4&R2"OK -- chat-script cisco-dial"""AT"TIMEOUT 30 OK" ATDT\T" TIMEOUT 30 CONNECT\c
-- interface async1
---- encapsulation ppp
---- async default routing
---- async mode dedicated
---- dialer in-band
---- ip unnumbered Ethernet0
---- ip tcp header-compression passive
---- dialer idle-timeout 300
---- dialer map ip 20.1.1.1 name Guangzhou 020********
---- ppp authentication chap
-- line aux 0
---- script dialer cisco-dial
---- script reset rstmdm
---- modem inout
----modem autoconfig discovery
---- transport input all
---- rxspeed 38400
---- txspeed 38400
---- stopbits 1
---- flowcontrol hardware
-- line vty 0 4
---- password telnet
---- login
3.Access Server实例
Router:
hostname Router
enable secret 5 $ 1$EFqU$tYLJLrynNUKzE4bx6fmH// chat-script cisco-default ABORT ERROR "" "AT Z"OK "ATDT\T"TIMEOUT 30\c CONNE
interface Ethernet0
--ip address 10.111.4.20 255.255.252.0
interface Async1
--ip unnumbered Ethernet0
cencapsulation ppp
--keepalive 10
--async mode interactive
--peer default ip address pool Cisco 2511-Group-142
--ppp authentication pap
ip local pool Cisco2511-Group-142 10.111.4.21 10.111.4.36
tacacs-server host 10.111.4.2
line 1
--script dialer cisco-default
--login authentication tacacs
--modem InOut
--modem autoconfigure discovery
--flowcontrol hardware
五、ISDN MPPP
1.相关命令
全局设置:
设置ISDN交换类型 isdn switch-type basic-nil
接口设置
设备PPP封装 encapsulation ppp
启动PPP多连接 ppp multilink
设置启动另一个B通道的阈值 dialer load-threshold load
2.举例:
Router1:
isdn switch-type basic-nil
interface Serial0
-- ip address 192.200.10.1 255.255.255.0
-- encapsulation ppp
-- dialer map ip 192.200.10.2 54321
-- dialer load-threshold 80
-- ppp multilink