当前位置：文档库 › 160683630H-F中文资料

160683630H-F中文资料

Radial Box Metallized Polyester Capacitors

Speci?cations

The Type 160 series radial lead metallized polyester box capacitors are constructed in rugged rectangular plastic cases with lead spacings that are standard in the electron-ics industry. All Type 160 capacitors are available in bulk with a .217” ±.039” lead length, and they are good for general purpose applications such as bypass, decou-pling, energy storage/discharge and arc suppression.

Highlights

? RoHS compliant ? Rugged plastic case

? Case and epoxy ?ll meets UL94V0 ? 10 mm through 27.5 mm lead spacings ? Non-inductively wound ? Non-polar

Wire lead material, tinned copper clad steel

Capacitance Range:

Voltage Range:

Capacitance Tolerance:

Operating Temperature Range: Dielectric Withstand Voltage:

Dissipation Factor (DF):

Total Self Inductance (L):

Long Term Stability (after two years): Corona (Partial Discharge Inception Voltage): Maximum Pulse Rise Time (dv/dt):

0.0022 μF to 10.0 μF

63 Vdc to 1000 Vdc (40 Vac - 250 Vac 50/60 Hz) ±5%, ±10%, ±20%

–55 oC to +125 oC (with 50% Vdc derating >85 oC) 1.6 x rated voltage for 2 sec @ +25 oC ±5 oC tan δ x 10–4 at 25 oC ±5 oC

kHz C ≤1 μF C >1 μF 1 ≤100 ≤100

≥150 Pitch (mm) 10 15 22.5 27.5 L (nH) ≈

Capacitance change ?C/C ≤ ±3% under stan-dard environmental conditions

200 Vac for 100 Vdc, 200 Vdc

250 Vac for 400 Vdc, 630 Vdc 300 Vac for 1000 Vdc

Pitch (mm) Vn 10 15 22.5 27.5 63 100/160 250 400 630 1000

3 6/8 11 20 30 60

1.5 3 7 10 15 25

1 2 4 5.5 8 15

1 1 3 5 7 10

If the working voltage (V) is less than the nominal voltage (Vn), the capacitor can work at higher dv/dt. In this case, the maximum value allowed is obtained by multiplying the above value with the ratio Vn/V.

Capacitor Outline Drawing

Test Method and Performance

L Max

Max

H Max

S ±.015 (±0.4 mm)

.217 ±.039

(5.5 ±1.0 mm)

?d ±0.002 (±0.05 mm)

Note: The lead diameter is a maximum dimen-sion for lead spacing ≤15 mm and a nominal for

lead spacing >15 mm

Soldering

Test Conditions Soldering Temperature 260 oC ±5 oC Soldering Duration 10 sec ±1 sec

Performance

Capacitance Change ?C/C ≤ ±2% DF Change ?tg δ

≤30 x 10–4

at 10 kHz for C ≤1.0 μF

≤20 x 10–4 at 1 kHz for C >1.0 μF

Insulation Resistance

Test Conditions T emperature

25 oC ±5 oC Voltage Charge Time 1 minute

Voltage Charge 50 Vdc for Vn < 100 Vdc 100 Vdc for Vn ≥ 100 Vdc

Performance For Vn > 100 Vdc ≥30,000 M ? for ≤ 0.33μF ≥10,000 M ? x μF for C > 0.33μF For Vn ≤100 Vdc

≥10,000 M ? for C ≤ 0.1μF ≥1,000 M ? x μF for ≤ 0.1μF

Damp Heat Test

Test Conditions T emperature

+40 oC Relative Humidity

95% T est Duration

21 days Performance Capacitance Change ?C/C ≤ ±5%

DF Change ?tg δ

≤50 x 104 at 1 kHz Insulation Resistance

≥ 50% of limit value Life Test

Test Conditions T emperature +85 oC T est Duration 1000 hrs Voltage Applied 1.25 x Vn Performance

Capacitance Change ?C/C

≤ ±5%

DF Change ?tg δ

≤30 x 10–4 at 10 kHz for C ≤1.0 μF ≤20 x 10–4 at 1 kHz for C >1.0 μF

Insulation Resistance

≥ 50% of limit value

Ratings

RoHS Compliant

Cap Catalog Inches Millimeters (μF)

Part Number

S ?d L T H S ?d 63 Vdc / 40 Vac

.22.27.33 160224*63C–F 160274*63C–F 160334*63C–F 0.512 0.512 0.512 0.157 0.157 0.157 0.374 0.374 0.374 0.394 0.394 0.394 0.031 0.031 0.031 13.0 13.0 13.0 4.0 4.0 4.0 9.5 9.5 9.5 10.0 10.0 10.0 0.8 0.8 0.8 .39 160394*63C–F 0.512 0.157 0.374 0.394 0.031 13.0 4.0 9.5 10.0 0.8 .47 160474*63D–F 0.512 0.197 0.433 0.394 0.031 13.0 5.0 11.0 10.0 0.8 .56 160564*63D–F 0.512 0.197 0.433 0.394 0.031 13.0 5.0 11.0 10.0 0.8 .68 160684*63D–F 0.512 0.197 0.433 0.394 0.031 13.0 5.0 11.0 10.0 0.8 .68 160684*63F–F 0.709 0.197 0.433 0.591 0.031 18.0 6.0 12.0 15.0 0.8 .82 160824*63E–F 0.512 0.236 0.472 0.394 0.031 13.0 6.0 12.0 10.0 0.8 .82 160824*63F–F 0.709 0.197 0.433 0.591 0.031 18.0 5.0 11.0 15.0 0.8 1.0 160105*63E–F 0.512 0.236 0.472 0.394 0.031 13.0 6.0 12.0 10.0 0.8 1.0 160105*63F–F 0.709 0.197 0.433 0.591 0.031 18.0 5.0 11.0 15.0 0.8 1.5 160155*63F–F 0.709 0.197 0.433 0.591 0.031 18.0 6.0 12.0 15.0 0.8 2.2 160225*63G–F 0.709 0.236 0.472 0.591 0.031 18.0 7.5 13.5 15.0 0.8 3.3 160335*63M–F 1.043 0.276 0.630 0.886 0.031 26.5 7.0 16.5 22.5 0.8 4.7 160475*63N–F 1.043 0.335 0.669 0.886 0.031 26.5 8.5 17.0 22.5 0.8 6.8 160685*63O–F 1.043 0.394 0.748 0.886 0.031 26.5 10.0 19.0 22.5 0.8 10.0 160106*63P–F 1.260 0.433 0.787 1.083 0.031

32.0

11.0

20.0

27.5

0.8

* Indicates capacitance tolerance: J = ±5%, K = ±10%, M = ±20%

Cap (μF)

Catalog

Part Number

Inches Millimeters

L T H S ?d L T H S ?d

100 Vdc / 63 Vac

.10 .12 .15160104*100C–F

160124*100C–F

160154*100C–F

0.512

0.157

0.374

0.394

0.031

13.0

4.0

9.5

10.0

0.8

.18 160184*100C–F 0.512 0.157 0.374 0.394 0.031 13.0 4.0 9.5 10.0 0.8 .22 160224*100D–F 0.512 0.197 0.433 0.394 0.031 13.0 5.0 11.0 10.0 0.8 .27 160274*100D–F 0.512 0.197 0.433 0.394 0.031 13.0 5.0 11.0 10.0 0.8 .33 160334*100E–F 0.512 0.236 0.472 0.394 0.031 13.0 6.0 12.0 10.0 0.8 .33 160334*100F–F 0.709 0.197 0.433 0.591 0.031 18.0 5.0 11.0 15.0 0.8 .39 160394*100D–F 0.512 0.197 0.433 0.394 0.031 13.0 6.0 12.0 10.0 0.8 .39 160394*100F–F 0.709 0.197 0.433 0.591 0.031 18.0 5.0 11.0 15.0 0.8 .47 160474*100E–F 0.512 0.236 0.472 0.394 0.031 13.0 6.0 12.0 10.0 0.8 .47 160474*100F–F 0.709 0.197 0.433 0.591 0.031 18.0 5.0 11.0 15.0 0.8 .56 160564*100G–F 0.709 0.236 0.472 0.591 0.031 18.0 6.0 12.0 15.0 0.8 .68 160684*100G–F 0.709 0.236 0.472 0.591 0.031 18.0 6.0 12.0 15.0 0.8 .82 160824*100H–F 0.709 0.295 0.531 0.591 0.031 18.0 7.5 13.5 15.0 0.8

1.0 160105*100H–F 0.709 0.295 0.531 0.591 0.031 18.0 7.5 13.5 15.0 0.8

1.5 160155*100M–F 1.043 0.276 0.630 0.886 0.031 26.5 7.0 16.5 2

2.5 0.8

2.2 160225*100N–F 1.043 0.335 0.669 0.886 0.031 26.5 8.5 17.0 22.5 0.8

3.3 160335*100O–F 1.043 0.394 0.748 0.886 0.031 26.5 10.0 19.0 22.5 0.8

4.7 160475*100P–F 1.260 0.433 0.787 1.083 0.031 32.0 11.0 20.0 27.5 0.8

6.8 160685*100Q–F 1.260 0.512 0.886 1.083 0.031 32.0 13.0 22.5 2

7.5 0.8

10.0 160106*100S–F 1.457 0.709 1.299 1.083 0.031 37.0 18.0 33.0 27.5 0.8

160 Vdc / 100 Vac

.10 160104*160C–F 0.512 0.157 0.374 0.394 0.031 13.0 4.0 9.5 10.0 0.8

250 Vdc /160 Vac

.033 160333*250C–F 0.512 0.157 0.374 0.394 0.031 13.0 4.0 9.5 10.0 0.8 .039 160393*250C–F 0.512 0.157 0.374 0.394 0.031 13.0 4.0 9.5 10.0 0.8 .047 160473*250C–F 0.512 0.157 0.374 0.394 0.031 13.0 4.0 9.5 10.0 0.8 .056 160563*250C–F 0.512 0.157 0.374 0.394 0.031 13.0 4.0 9.5 10.0 0.8 .068 160683*250C–F 0.512 0.157 0.374 0.394 0.031 13.0 4.0 9.5 10.0 0.8 .082 160823*250D–F 0.512 0.197 0.433 0.394 0.031 13.0 5.0 11.0 10.0 0.8 .10 160104*250D–F 0.512 0.197 0.433 0.394 0.031 13.0 5.0 11.0 10.0 0.8 .10 160104*250F–F 0.709 0.197 0.433 0.591 0.031 18.0 5.0 11.0 15.0 0.8 .12 160124*250D–F 0.512 0.197 0.433 0.394 0.031 13.0 6.0 12.0 10.0 0.8 .12 160124*250F–F 0.709 0.197 0.433 0.591 0.031 18.0 5.0 11.0 15.0 0.8 .15 160154*250E–F 0.512 0.236 0.472 0.394 0.031 13.0 6.0 12.0 10.0 0.8 .15 160154*250F–F 0.709 0.197 0.433 0.591 0.031 18.0 5.0 11.0 15.0 0.8 .18 160184*250E–F 0.512 0.236 0.472 0.394 0.031 13.0 6.0 12.0 10.0 0.8 .18 160184*250F–F 0.709 0.197 0.433 0.591 0.031 18.0 5.0 11.0 15.0 0.8 .22 160224*250F–F 0.709 0.197 0.433 0.591 0.031 18.0 5.0 11.0 15.0 0.8 .27 160274*250G–F 0.709 0.236 0.472 0.591 0.031 18.0 6.0 12.0 15.0 0.8 .33 160334*250G–F 0.709 0.236 0.472 0.591 0.031 18.0 6.0 12.0 15.0 0.8 .39 160394*250H–F 0.709 0.295 0.531 0.591 0.031 18.0 7.5 13.5 15.0 0.8 .47 160474*250H–F 0.709 0.295 0.531 0.591 0.031 18.0 7.5 13.5 15.0 0.8 .47 160474*250L–F 1.043 0.236 0.591 0.886 0.031 26.5 6.0 15.0 22.5 0.8 .56 160564*250I–F 0.709 0.335 0.571 0.591 0.031 18.0 8.5 14.5 15.0 0.8 .56 160564*250M–F 1.043 0.276 0.63 0.886 0.031 26.5 7.0 16.0 22.5 0.8 .68 160684*250I–F 0.709 0.335 0.571 0.591 0.031 18.0 8.5 14.5 15.0 0.8 .68 160684*250M–F 1.043 0.276 0.63 0.886 0.031 26.5 7.0 16.5 22.5 0.8 .82 160824*250M–F 1.043 0.276 0.63 0.886 0.031 26.5 8.5 17.0 22.5 0.8 * Indicates capacitance tolerance: J = ±5%, K = ±10%, M = ±20%

Cap (μF)

Catalog Part Number

Inches

Millimeters

L T H S ?d

L T H S ?d 250 Vdc / 160 Vac

1.01.5

2.2 160105*250N–F 160155*250O–F 160225*250P–F 1.043 1.043 1.260 0.335 0.394 0.433 0.669 0.748 0.787 0.886 0.886 1.083 0.031 0.031 0.031 26.5 26.5 32.0 8.5 10.0 11.0 17.0 19.0 20.0 22.5 22.5 27.5 0.8 0.8 0.8

3.3 160335*250Q–F 1.260 0.512 0.886 1.083 0.031 32.0 13.0 22.5 27.5 0.8

4.7 160475*250R–F 1.260 0.591 1.181 1.083 0.031 32.0 1

5.0 30.0 27.5 0.8

6.8 160685*250S–F 1.457 0.709 1.299 1.083 0.031

37.0 18.0 33.0 27.5 0.8 400 Vdc / 200 Vac

.012.015.018 160123*400C–F 160153*400C–F 160183*400C–F 0.512 0.512 0.512 0.157 0.157 0.157 0.374 0.374 0.374 0.394 0.394 0.394 0.031 0.031 0.031 13.0 13.0 13.0 4.0 4.0 4.0 9.5 9.5 9.5 10.0 10.0 10.0 0.8 0.8 0.8 .022 160223*400C–F 0.512 0.157 0.374 0.394 0.031 13.0 4.0 9.5 10.0 0.8 .027 160273*400C–F 0.512 0.157 0.374 0.394 0.031 13.0 4.0 9.5 10.0 0.8 .033 160333*400D–F 0.512 0.197 0.433 0.394 0.031 13.0 5.0 11.0 10.0 0.8 .039 160393*400D–F 0.512 0.197 0.433 0.394 0.031 13.0 5.0 11.0 10.0 0.8 .047 160473*400E–F 0.512 0.236 0.472 0.394 0.031 13.0 6.0 12.0 10.0 0.8 .047 160473*400F–F 0.709 0.197 0.433 0.591 0.031 18.0 5.0 11.0 15.0 0.8 .056 160563*400F–F 0.709 0.197 0.433 0.591 0.031 18.0 5.0 11.0 15.0 0.8 .068 160683*400F–F 0.709 0.197 0.433 0.591 0.031 18.0 5.0 11.0 15.0 0.8 .082 160823*400F–F 0.709 0.197 0.433 0.591 0.031 18.0 5.0 11.0 15.0 0.8 .10 160104*400G–F 0.709 0.236 0.472 0.591 0.031 18.0 6.0 12.0 15.0 0.8 .12 160124*400G–F 0.709 0.236 0.472 0.591 0.031 18.0 6.0 12.0 15.0 0.8 .15 160154*400H–F 0.709 0.295 0.531 0.591 0.031 18.0 7.5 13.5 15.0 0.8 .15 160154*400L–F 1.043 0.236 0.591 0.886 0.031 26.5 6.0 15.0 22.5 0.8 .18 160184*400L–F 1.043 0.236 0.591 0.886 0.031 26.5 6.0 15.0 22.5 0.8 .22 160224*400L–F 1.043 0.236 0.591 0.886 0.031 26.5 6.0 15.0 22.5 0.8 .27 160274*400M–F 1.043 0.276 0.630 0.886 0.031 26.5 7.0 16.5 22.5 0.8 .33 160334*400M–F 1.043 0.276 0.630 0.886 0.031 26.5 7.0 16.5 22.5 0.8 .39 160394*400N–F 1.043 0.335 0.669 0.886 0.031 26.5 8.5 17.0 22.5 0.8 .47 160474*400N–F 1.043 0.335 0.669 0.886 0.031 26.5 8.5 17.0 22.5 0.8 .56 160564*400O–F 1.043 0.394 0.748 0.886 0.031 26.5 10.0 19.0 22.5 0.8 .68 160684*400P–F 1.26 0.433 0.787 1.083 0.031 32.0 11.0 20.0 27.5 0.8 .82 160824*400P–F 1.26 0.433 0.787 1.083 0.031 32.0 11.0 20.0 27.5 0.8 1.0 160105*400P–F 1.26 0.433 0.787 1.083 0.031 32.0 11.0 20.0 27.5 0.8 1.0 160105*400Q–F 1.26 0.512 0.886 1.083 0.031

32.0 13.0 22.5 27.5 0.8 630 Vdc / 220 Vac

.0039.0047.0056 160392*630C–F 160472*630C–F 160562*630C–F 0.512 0.512 0.512 0.157 0.157 0.157 0.374 0.374 0.374 0.394 0.394 0.394 0.031 0.031 0.031 13.0 13.0 13.0 4.0 4.0 4.0 9.5 9.5 9.5 10.0 10.0 10.0 0.8 0.8 0.8 .0068 160682*630C–F 0.512 0.157 0.374 0.394 0.031 13.0 4.0 9.5 10.0 0.8 .0082 160822*630C–F 0.512 0.157 0.374 0.394 0.031 13.0 4.0 9.5 10.0 0.8 .010 160103*630C–F 0.512 0.157 0.374 0.394 0.031 13.0 4.0 9.5 10.0 0.8 .012 160123*630D–F 0.512 0.197 0.433 0.394 0.031 13.0 5.0 11.0 10.0 0.8 .015 160153*630D–F 0.512 0.197 0.433 0.394 0.031 13.0 5.0 11.0 10.0 0.8 .018 160183*630D–F 0.512 0.197 0.433 0.394 0.031 13.0 5.0 11.0 10.0 0.8 .022 160223*630E–F 0.512 0.236 0.472 0.394 0.031 13.0 6.0 12.0 10.0 0.8 .027 160273*630F–F 0.709 0.197 0.433 0.591 0.031 18.0 5.0 11.0 15.0 0.8 .033 160333*630F–F 0.709 0.197 0.433 0.591 0.031 18.0 5.0 11.0 15.0 0.8 .039 160393*630G–F 0.709 0.236 0.472 0.591 0.031 18.0 6.0 12.0 15.0 0.8 .047 160473*630G–F 0.709 0.236 0.472 0.591 0.031 18.0 6.0 12.0 15.0 0.8 .056 160563*630G–F 0.709 0.236 0.472 0.591 0.031 18.0

6.0

12.0

15.0

0.8

* Indicates capacitance tolerance: J = ±5%, K = ±10%, M = ±20%

Cap (μF) Catalog Part Number Inches Millimeters L T H S ?d L T H S ?d 630 Vac / 220 Vac .068.068.082 160683*630H–F 160683*630L–F 160823*630L–F 0.709 1.043 1.043 0.295 0.236 0.236 0.531 0.591 0.591 0.591 0.886 0.886 0.031 0.031 0.031 18.0

26.5 26.5 7.5 6.0 6.0 13.5 15.0 15.0 15.0 22.5 22.5 0.8 0.8 0.8 .10 160104*630L–F 1.043 0.236 0.591 0.886 0.031 26.5 6.0 15.0 22.5 0.8 .12 160124*630M–F 1.043 0.276 0.630 0.886 0.031 26.5 7.0 16.5 22.5 0.8 .15 160154*630M–F 1.043 0.276 0.630 0.886 0.031 26.5 7.0 16.5 22.5 0.8 .18 160184*630N–F 1.043 0.335 0.669 0.886 0.031 26.5 8.5 17.0 22.5 0.8 .22 160224*630N–F 1.043 0.335 0.669 0.886 0.031 26.5 8.5 17.0 22.5 0.8 .27 160274*630Q–F 1.26 0.512 0.886 1.083 0.031 32.0 13.0 22.5 27.5 0.8 .33 160334*630P–F 1.26 0.433 0.787 1.083 0.031 32.0 11.0 20.0 27.5 0.8 .39 160394*630P–F 1.26 0.433 0.787 1.083 0.031 32.0 11.0 20.0 27.5 0.8 .47 160474*630Q–F 1.26 0.512 0.886 1.083 0.031 32.0 13.0 22.5 27.5 0.8 1000 Vdc / 250 Vac .0022.0027.0033 160222*1000C–F 160272*1000C–F 160332*1000C–F 0.512 0.512 0.512 0.157 0.157 0.157 0.374 0.374 0.374 0.394 0.394 0.394 0.031 0.031 0.031 13.0 13.0 13.0 4.0 4.0 4.0 9.5 9.5 9.5 10.0 10.0 10.0 0.8 0.8 0.8 .0039 160392*1000D–F 0.512 0.197 0.433 0.394 0.031 13.0 5.0 11.0 10.0 0.8 .0047 160472*1000D–F 0.512 0.197 0.433 0.394 0.031 13.0 5.0 11.0 10.0 0.8 .0056 160562*1000D–F 0.512 0.197 0.433 0.394 0.031 13.0 5.0 11.0 10.0 0.8 .0068 160682*1000D–F 0.512 0.197 0.433 0.394 0.031 13.0 5.0 11.0 10.0 0.8 .0082 160822*1000D–F 0.512 0.197 0.433 0.394 0.031 13.0 5.0 11.0 10.0 0.8 .010 160103*1000F–F 0.709 0.197 0.433 0.591 0.031 18.0 5.0 11.0 15.0 0.8 .012 160123*1000F–F 0.709 0.197 0.433 0.591 0.031 18.0 5.0 11.0 15.0 0.8 .015 160153*1000F–F 0.709 0.197 0.433 0.591 0.031 18.0 6.0 12.0 15.0 0.8 .018 160183*1000G–F 0.709 0.236 0.472 0.591 0.031 18.0 6.0 12.0 15.0 0.8 .022 160223*1000G–F 0.709 0.236 0.472 0.591 0.031 18.0 6.0 12.0 15.0 0.8 .027 160273*1000H–F 0.709 0.295 0.531 0.591 0.031 18.0 7.5 13.5 15.0 0.8 .033 160333*1000L–F 1.043 0.236 0.591 0.886 0.031 26.5 6.0 15.0 22.5 0.8 .039 160393*1000L–F 1.043 0.236 0.591 0.886 0.031 26.5 6.0 15.0 22.5 0.8 .047 160473*1000L–F 1.043 0.236 0.591 0.886 0.031 26.5 6.0 15.0 22.5 0.8 .056 160563*1000M–F 1.043 0.276 0.630 0.886 0.031 26.5 7.0 16.5 22.5 0.8 .068 160683*1000M–F 1.043 0.276 0.630 0.886 0.031 26.5 7.0 16.5 22.5 0.8 .082 160823*1000N–F 1.043 0.335 0.669 0.886 0.031 26.5 8.5 17.0 22.5 0.8 .10 160104*1000N–F 1.043 0.335 0.669 0.886 0.031 26.5 8.5 17.0 22.5 0.8 .12 160124*1000O–F 1.043 0.394 0.748 0.886 0.031 26.5 10.0 19.0 22.5 0.8 .15 160154*1000P–F 1.26 0.433 0.787 1.083 0.031 32.0 11.0 20.0 27.5 0.8 .18 160184*1000Q–F 1.26 0.512 0.886 1.083 0.031 32.0 13.0 22.5 27.5 0.8 .22

160224*1000Q–F

1.26

0.512

0.886 1.083 0.031

32.0

13.0

22.5

27.5

0.8

* Indicates capacitance tolerance: J = ±5%, K = ±10%, M = ±20%

Part Numbering System

160

104

100

C Case

Series Capacitance Tolerance Voltage Code 160

392 = .0039 μF J = ±5% 100 = 100 Vdc C 103 = .01 μF K = ±10% 250 = 250 Vdc D 104 = .1 μF M = ±20%

630 = 630 Vdc E 105 = 1.0 μF

1000 = 1000 Vdc

F etc.