注塑模具专业词汇
模具专业英语词汇一、入水：gate
进入位：gate location
水口形式：gate type
大水口：edge gate
细水口：pin-point gate
水口大小：gate size
转水口：switching runner/gate
唧嘴口径：sprue diameter
二、流道: runner
热流道：hot runner,hot manifold
热嘴冷流道: hot sprue/cold runner
唧嘴直流: direct sprue gate
圆形流道：round(full/half runner
流道电脑分析：mold flow analysis
流道平衡:runner balance
热嘴：hot sprue
热流道板：hot manifold
发热管：cartridge heater
探针: thermocouples
插头：connector plug
插座：connector socket
密封/封料：seal
三、运水：water line
喉塞：line lpug
喉管：tube
塑胶管：plastic tube
快速接头：jiffy quick connector plug/socker 四、模具零件：mold components
三板模：3-plate mold
二板模：2-plate mold
边钉/导边：leader pin/guide pin
边司/导套：bushing/guide bushing
中托司：shoulder guide bushing
中托边L：guide pin
顶针板：ejector retainner plate
托板：support plate
螺丝：screw
管钉：dowel pin
开模槽：ply bar scot
内模管位：core/cavity inter-lock
顶针：ejector pin
司筒：ejector sleeve
司筒针：ejector pin
推板：stripper plate
模具述语
一、入水：gate
进入位：gate location
水口形式：gate type
大水口：edge gate
细水口： pin-point gate
水口大小：gate size
转水口：switching runner/gate
唧嘴口径：sprue diameter
二、流道: runner
热流道：hot runner,hot manifold
热嘴冷流道: hot sprue/cold runner
唧嘴直流: direct sprue gate
圆形流道：round(full/half runner
流道电脑分析：mold flow analysis
流道平衡:runner balance
热嘴：hot sprue
热流道板：hot manifold
发热管：cartridge heater
探针: thermocouples
插头：connector plug
插座： connector socket
密封/封料： seal
三、运水：water line
喉塞：line lpug
喉管：tube
塑胶管：plastic tube
快速接头：jiffy quick connector plug/socker 四、模具零件：mold components
三板模：3-plate mold
二板模：2-plate mold
边钉/导边：leader pin/guide pin
边司/导套：bushing/guide bushing
中托司：shoulder guide bushing
中托边L：guide pin
顶针板：ejector retainner plate
托板：support plate
螺丝： screw
管钉：dowel pin
开模槽：ply bar scot
内模管位：core/cavity inter-lock
顶针：ejector pin
司筒：ejector sleeve
司筒针：ejector pin
推板：stripper plate
缩呵：movable core,return core core puller
扣机（尼龙拉勾）：nylon latch lock
斜顶：lifter
模胚（架）： mold base
上内模：cavity insert
下内模：core insert
行位（滑块）： slide
镶件：insert
压座/斜鸡：wedge
耐磨板/油板：wedge wear plate
压条：plate
撑头: support pillar
唧嘴： sprue bushing
挡板：stop plate
定位圈：locating ring
锁扣：latch
扣鸡：parting lock set
推杆：push bar
栓打螺丝：S.H.S.B
顶板：eracuretun
活动臂：lever arm
分流锥：spure sperader
水口司:bush
垃圾钉：stop pin
隔片：buffle
弹弓柱：spring rod
弹弓:die spring
中托司：ejector guide bush
中托边：ejector guide pin
镶针：pin
销子：dowel pin
波子弹弓：ball catch
喉塞: pipe plug
锁模块：lock plate
斜顶：angle from pin
斜顶杆：angle ejector rod
尼龙拉勾：parting locks
活动臂：lever arm
复位键、提前回杆：early return bar
气阀：valves
斜导边：angle pin
术语：terms
承压平面平衡：parting surface support balance
模排气：parting line venting
回针碰料位：return pin and cavity interference
模总高超出啤机规格：mold base shut hight
顶针碰运水：water line interferes withejector pin
料位出上/下模：part from cavith (core) side
模胚原身出料位：cavity direct cut on A-plate,core direct cut on B-plate. 不准用镶件： Do not use (core/cavity) insert
用铍铜做镶件： use beryllium copper insert
初步（正式）模图设计：preliinary (final) mold design
反呵：reverse core
弹弓压缩量：spring compressed length
稳定性好：good stability,stable
强度不够：insufficient rigidity
均匀冷却：even cooling
扣模：sticking
热膨胀：thero expansion
公差：tolorance
铜公(电极）：copper electrode
angle pin. finger cam (-:-) 斜销
angled-lift. splits (-:-) 斜滑块
backing plate. supprr plate (-:-) 支承板
baffle (-:-) 隔板
cartridge heater (-:-) 管式加热器
cavity (of a mould) (-:-) 型腔
cavity splits (-:-) 凹模拼块
cavity-retainer plate (-:-) 凹模固定板
chase. bolster. frame (-:-) 模套
clamping force. locking force (-:-) 锁模力
clog-leg cam (-:-) 弯销
cold-slug well (-:-) 冷料穴
compression mould (-:-) 压缩模
cooling channel. cooling line (-:-) 冷却通道
core splits (-:-) 型芯拼块
core splits (-:-) 型芯
core-pulling distance (-:-) 抽芯距
core-pulling force (-:-) 油芯力
core-retainer plate (-:-) 型芯固定板
dejection plate. ejector plate (-:-) 推板
direct gate spruce gate (-:-) 直接浇口
director guide fush. ejector bushing (-:-) 推板导套
disk gate (-:-) 盘形浇口
draft (-:-) 脱模斜度
edge gate (-:-) 侧浇口
ejection force (-:-) 脱模力
ejector guide pillar. ejector guide pin (-:-) 推板导柱
ejector housing. mould base leg (-:-) 支架
ejector pad (-:-) 推块
ejector pin (-:-) 推出零件/推杆
ejector pin with cylindrical head (-:-) 圆柱头推杆
ejector plate return pin. push-back pin (-:-) 复位杆
ejector retainer plate (-:-) 推杆固定板
ejector sleeve (-:-) 推管
ejector tie rod (-:-) 连接推杆
fan gate (-:-) 扇形浇口
feed system (-:-) 浇注系统
finger guide plate (-:-) 斜槽导板
fixed clamp plate, top clamping plate. top plate (-:-) 定模座板fixed compression mould (-:-) 固定式压缩模
fixed transfer mould (-:-) 固定式压注模
flash groove, spew groove (-:-) 排溢：溢料槽
flash mould (-:-) 溢式压缩模
flat ejector pin (-:-) 扁推杆
force plunger, pot plunger (-:-) 柱塞
gate (-:-) 浇口
gating insert (-:-) 浇口镶块
guide bush. guide bushing (-:-) 导套
guide fush, hended. shonlder bushing (-:-) 带头导套
guide fush, straight. shraighr bushing (-:-) 直导套
guide pillar straight. straight leader pin (-:-) 带头导柱
guide pillar. guide pin. leader pin (-:-) 导柱
guide pillar. shouldered. shoulder leader pin (-:-) 带肩导柱heat pipe (-:-) 热管
heating plate (-:-) 加热板
heel block, wedge block (-:-) 楔紧块
horingontal parting line (-:-) 水平分型面(线)
hot runner mould (-:-) 热流道模
impression cavity block. cavity plate (-:-) 凹模
injection mould (-:-) 注射模
injection mould for thermoplastics (-:-) 热塑性塑料注射模injection mould for thermoses (-:-) 热固性塑料注射模injection pressure (-:-) 注射压力
inserf (for moulding) (-:-) 嵌件
insulated runner mould (-:-) 绝热流道模
internal mould pressure. cavity pressure (-:-) 模内压力internal mould pressure. cavity pressure (-:-) 模内压力length bolt. puller bolt (-:-) 定矩拉杆
loading chamber (-:-) 加料腔
loading chamber (-:-) 加料腔
locating ring (-:-) 定位圈/限位零件
lower clamping plate (-:-) 下模座板
lower mould. lower half (-:-) 下模
manifold block hot-runner manifold (-:-) 热流道板（柱）
maximum daylight, open daylight (-:-) 最大开距
maximum daylight, open daylight (-:-) 最大开距
maximum daylight, open daylight (-:-) 最大开距
mould bases (of a injection mould) (-:-) 模架(注射模)
mould bases locating elements (-:-) 锥形定位件
mould for plastics (-:-) 塑料成形模具
mould for plastics (-:-) 塑料成形模具
mould for thermoplastics (-:-) 热塑性塑料模
mould for thermosets (-:-) 热固性塑料模
mould insert (-:-) 镶件
mould opening force (-:-) 开模力
mould plate (-:-) 模板
mould shut height (-:-) 闭合高度
moulding pressure (-:-) 成形压力
movable insert. loose detail (-:-) 活动镶件
movable insert. loose detail (-:-) 活动镶件
movable mould moving half (-:-) 动模
moving clamp plate. bottom clamping plate. bottom plate (-:-) 动模座板parting line (-:-) 分型：分型面
pin-point gate (-:-) 点浇口
portable compression mould (-:-) 移动式压缩模
portable transfer mould (-:-) 移动式压注模
positive mould (-:-) 不溢式压缩模
projected area (-:-) 投影面积
projected area (-:-) 投影面积
puller plate. limit plate (-:-) 定矩拉板
punch force (-:-) 凸模
punch-retainer plate (-:-) 凸模固定板
ring gate (-:-) 环形浇口
runner (-:-) 分流道
runner plate (-:-) 流道板
runner puller. runner lock pin (-:-) 分流道拉料杆
runner stripper plate (-:-) 推流道板
runnerless mould (-:-) 无浇道模
secondary nozzle (-:-) 二级喷嘴
semi-positive mould (-:-) 半溢式压缩模
shot capacity (-:-) 注射能力
shot capacity (-:-) 注射能力
shouldered ejector pin (-:-) 带肩推杆
shrinkage (-:-) 收缩率
side core. slide core (-:-) 侧型芯
slide glide strip (-:-) 滑块导板
slide. cam slide (-:-) 滑块
slide. core-slide (-:-) 侧型芯滑块
spacer parallel (-:-) 垫块
splits (of a mould) (-:-) 拼块
spoke gate spider gate (-:-) 轮辐浇口spreader (-:-) 分流锥
spruce (-:-) 主流道
sprue bush sprue busing (-:-) 浇口套
sprue puller (-:-) 拉料杆
sprue puller, ball headed (-:-) 球头拉料杆sprue puller, z-shaper (-:-) 钩形拉料杆
sprue puller. conical headed (-:-) 圆锥头拉料杆sprue puller. conical headed (-:-) 圆锥头拉料杆standard mould bases (-:-) 标准模架standard mould bases (-:-) 标准模架standard mould bases (-:-) 标准模架stationary mould fixed half (-:-) 定模
stop flock, stop pad (-:-) 限位块
stop pin. stop button (-:-) 限位钉
stripper distance (-:-) 脱模距
stripper distance (-:-) 脱模距
stripper plate (-:-) 推件板
stripper ring. strpper disk (-:-) 推件环/盘submarine gate tunnel gate (-:-) 潜伏浇口support pillar (-:-) 支承柱
ta be gate (-:-) 护耳浇口
thermal insulation board (-:-) 隔热板thermal insulation board (-:-) 隔热板
thread plug, threaded core (-:-) 螺纹型芯thread ring. threaded cavity (-:-) 螺纹型环torpedo body assembly (-:-) 鱼雷形组合体transfer mould (-:-) 压注模、传递模
upper clamping plate (-:-) 上模座板
upper mould, upper half (-:-) 上模
valve gate (-:-) 阀式浇口
venf (of a mould) (-:-) 排气槽（孔）
vertical parting line (-:-) 垂直分型面(线) warm runner mould (-:-) 温流道模
warm runner plate (-:-) 温流道板
模具专业英语词汇大全
模具专业英语词汇 A abrasion n. 磨损 abrasion resistance n. 耐磨损性 abrasive n. 磨料 accelerator n. 促进剂 accuracy n. 准确性 accurate die casting 精密压铸 air trap 积风 acrylic n. 丙烯酸 /压克力 ì active plate 活动板 additive n. 添加剂 adhere v. 黏附 adhesion n. 黏合 adhesive n. 胶粘剂 air-cushion eject-rod 气垫顶杆 air cushion plate 气垫板 air entrapment n. 困气 anneal v. 退火 assemble v. 总成 B back pressure 背压 bismuth mold 铋铸模 baffle plate 挡块 barrel n. 机筒 /料筒 / bending block 折刀 bottom block 下垫脚 bottom plate 下托板(底板) bushing bolck 衬套 barrel temperature 料筒温度 blush 发 blank through dies 漏件式落料模 burnishi blow molding n. 吹塑成型 blow molding machine n. 吹塑机 brittle adj. 脆性 bubble n. 气泡 burr 毛刺 button d by-product n. 副产品 C calendering n. 压延 carbon steel n. 碳素钢 casting n. 铸造 catalyst n. 催化剂 cavity n. 型腔 chemical resistance n. 耐化学腐蚀性 chip v. 削 /凿
注塑模具典型结构设计 关键机构之四——顺序开模控制机构04
4. 关键机构之四——顺序开模控制机构 该机构主要用于塑料件对动模和定模的附着力和包紧都相差不多的情况，例如所成型的塑料件在动模和定模侧都没有型芯，且塑料件对两型芯的收缩包紧力都相差不多时，又如塑料件由于内外壁脱模斜度不相等的原因造成对动定模留模倾向难以判断时，这时应该采用顺序开模控制机构，即在动模和定模两侧均有脱模机构，无论制品留在那一侧均能脱出。但是塑料件留模方位的不确定性会给操作带来不便，甚至在开模的瞬间可能会拉坏塑料件，因此最好的办法是开模时先使塑料件脱离定模，开模后制品留在动模侧，然后从动模侧推出塑料件，这种使用顺序脱模方式的脱模机构得到了广泛的应用。 4.1内装式顺序开模控制机构 4.1.1弹簧式顺序开模控制机构 1、如图4-1所示的弹簧式顺序开模控制机构中，定模侧使用弹簧的弹力推动脱模、动模侧使用推管推动脱模。如图4-1中所示，该塑料件为盘类零件，其留在动模侧，在定模侧设置弹簧启动的推出机构，分型时其作用为脱出流道凝料，同时对使塑料件留在定模侧也起到一定的作用。 2、模具开模时，在弹簧5的作用下，定模3与定模板4首先分型。在导柱2上开有一定距离的长槽，限位螺钉1的头部伸到长槽中，当开模到一定距离时，限位螺钉头部与长槽底部接触，定模3在限位螺钉与长槽的作用下停止向开模方向运动，使主分型面开始分型，同时使流道凝料与塑料件分离并脱出流道凝料。模具继续分型，在推管的作用下推出塑料件，完成模具开模。 3、弹簧式顺序开模控制机构的工作演示动画见光盘\chap04\4.1.1 弹簧式顺序开模控制机构。 如图4-1所示，为弹簧式顺序开模控制机构。
4.1.2 摆钩—弹簧顺序开模控制机构 摆钩式顺序分型是利用摆钩机构控制分型面的开模顺序，而弹簧式顺序分型机构是利用弹簧机构老控制注射模具分型面的开模顺序。摆钩与弹簧顺序开模控制机构将这两种顺序开模控制机构相结合，如图4-2所示的摆钩—弹簧顺序开模控制机构，弹簧4给摆钩2提供力的作用，利用摆钩与拉杆1的锁紧力增大开模力，以达到控制分型面的开模顺序。 1、模具开模时，由于弹簧4的作用摆钩2钩住拉杆1使摆钩与拉杆所在的部件在开模开始时保持闭模状态，待模具开模到一定的距离后，在定距限位装置的作用下，强行使拉杆1与摆钩2脱离，即模具进行第二次分型，以完成模具的整个开模过程。摆钩—弹簧顺序开模控制机构适用于各种二次分型场合，应用广泛，并且已经制定了相关标准供选用。 2、摆钩—弹簧顺序开模控制机构的工作演示动画见光盘\chap04\4.1.1 摆钩—弹簧顺序开模控制机构。 图4- 1 弹簧式顺序开模控制机构 1—限位螺钉；2—导柱；3—定模；4—定模座板；5—弹簧
注塑模具英文专业词汇大全
组合铣顶块Assemble mill 紫(纯)铜copper 注塑模具injection mold 注塑机injection machine 注射压力injection pressure 注射速率injection rate 注射能力shot capacity 主流道sprue 直浇口direct gate 支承板support plate 再生料recycle material 预热preheating 银条Silver streak 移印pad printing 循环时间cycle time 型腔cavity 斜销angle pin 镶件Insert 万能摇臂钻床Universal radial movable driller 万能铁床Universal milling machine 脱模斜度draft 脱模剂release agent
脱模ejection 涂层coating 凸模core plate 锁模力clamp force 缩水Sink mark 丝印Silk screen printing 水路钻孔加工drill water holes 双色注塑Double injection molding 双色注塑2K injection 数控加工中心CNC machine center 试生产Trial run; Pilot run (PR) 烧焦Burn mark 三板式模具three plate mold 熔合线Welding line 热熔Heat staking 热流道模具hot-runner mold 缺料Short mold 青铜bronze 切料头Degate 翘曲变形Deformation 嵌件注塑Insert molding 潜伏浇口submarine gate
模具专业英文术语大全
模具英语专业术语 模具述语 一、入水：gate 进入位： gate location 水口形式：gate type 大水口：edge gate 细水口： pin-point gate 水口大小：gate size 转水口： switching runner/gate 唧嘴口径： sprue diameter 二、流道: runner 热流道： hot runner,hot manifold 热嘴冷流道: hot sprue/cold runner 唧嘴直流: direct sprue gate 圆形流道：round(full/half runner 流道电脑分析：mold flow analysis 流道平衡:runner balance 热嘴： hot sprue 热流道板：hot manifold 发热管：cartridge heater 探针: thermocouples 插头： connector plug 插座： connector socket 密封/封料： seal 三、运水：water line 喉塞：line lpug 喉管：tube 塑胶管：plastic tube 快速接头：jiffy quick connector plug/socker 四、模具零件： mold components 三板模：3-plate mold 二板模：2-plate mold 边钉/导边：leader pin/guide pin 边司/导套：bushing/guide bushing 中托司：shoulder guide bushing 中托边L：guide pin 顶针板：ejector retainner plate 托板： support plate 螺丝： screw 管钉：dowel pin 开模槽：ply bar scot 内模管位：core/cavity inter-lock 顶针： ejector pin 司筒：ejector sleeve 司筒针：ejector pin 推板：stripper plate 缩呵：movable core,return core core puller 扣机（尼龙拉勾）：nylon latch lock 斜顶：lifter 模胚（架）： mold base 上内模：cavity insert 下内模：core insert 行位（滑块）： slide 镶件：insert 压座/斜鸡：wedge 耐磨板/油板：wedge wear plate 压条：plate 撑头: support pillar 唧嘴： sprue bushing 挡板：stop plate 定位圈：locating ring 锁扣：latch 扣鸡：parting lock set 推杆：push bar 栓打螺丝：S.H.S.B 顶板：eracuretun 活动臂：lever arm 分流锥：spure sperader 水口司:bush 垃圾钉：stop pin 隔片：buffle 弹弓柱：spring rod 弹弓:die spring 中托司：ejector guide bush 中托边：ejector guide pin 镶针：pin 销子：dowel pin 波子弹弓：ball catch 喉塞: pipe plug
塑胶模具专业英语
中文英文 机工,机器加工 machining,machine work O环,O形封垫 O ring 下料模,切料模 blanking die 寸进,寸动 inching 工程塑胶 engineering plastics 工模,夹具,支架 jig 干胶,粘著剂,动物胶 glue 干燥时间 drying time 干燥剂 drier dryer 不划一颜色,颜色深浅不均 color non-uni formity 中心浇口 center gate 内衬,衬套,衬蛰 liner 公差,容差 tolerance 分模线,合模线,模缝痕 parting line 切口,缺口 notch 切口,缺料 notch 切边(n) shear edge 化学腐蚀 chemical atching 化学腐蚀 chemical etching 反射 reflection 孔隙,空洞,气泡 void 尺寸稳定性 dimensional sability 手动压机 hand press 支管形喷嘴 nozzle manifold 比重 specific gravity 比热 specific heat 毛状裂痕 hair crack,hair cracking 毛绒 fuzz 毛边,凿纹 burr,flash,fin 水道,水通路 water channel 火花放电 spark discharge 火焰处理 flame treatment,flame treating 片材 sheet 凹痕,缩痕 sink mark,shrink mark 凹槽,内陷,凹陷 undercut 加料,给料,供料 feed 加热,加温 warming,warming up 加热板,热板(盘) heating plate 加热管套,加热缸 heating cylinder,heatin g barrel 加热炉 heating furnace 功率,力率 power factor 半透明 semitransparence,translucence 打眼,钻孔 driling 正余面,交叠,重叠 overlap 永久变形 permanent set,residual strain 白昙,雾状 haze 立式射出成型机 vertical injection mo(u)l ding machine 光彩,光泽 gloss 印刷 printing 同轴往复螺杆式射出成型机 in-line scre w(type)injecton mo(u)lding machine 合成树枝 synthetic resin 合板,集成材 composite wood 合模力,开模力 mo(u)ld clamping force, mo(u)ld locking force 合模线,毛边线 flash line,parting line 合模线,毛边线 spew line,spue line 合模销,导销 leader pin 合模销套,导销衬套 leader pin pushing 合模机构,开模机构 mo(u)ld clamping m echanism 后加工 post processing 后加热 after baking 后成型 postforming 回程销,复归销 return pin 安全系数 safety factor 安全门 safety door 成孔销,心型销,模蕊销 core pin 成孔销托板,动或定模板 core pin plate 成形 forming 成形,模制 mo(u)iding,forming
模具专业术语大全
模具专业英语词汇 landed plunger mold 有肩柱塞式模具?? burnishing die 挤光模英语站 landed positive mold 有肩全压式模具?? button die 镶入式圆形凹模 loading shoe mold 料套式模具 center-gated mold 中心浇口式模具loose detail mold 活零件模具 chill mold 冷硬用铸模 loose mold 活动式模具 clod hobbing 冷挤压制模 louvering die 百叶窗冲切模 composite dies 复合模具 manifold die 分歧管模具 counter punch 反凸模 modular mold 组合式模具 double stack mold 双层模具?? multi-cavity mold 多模穴模具?? electroformed mold 电铸成形模?? multi-gate mold 复式浇口模具?? expander die 扩径模?? offswt bending die 双折冷弯模具?? extrusion die 挤出模?? palletizing die 叠层模?? family mold 反套制品模具 plaster mold 石膏模 blank through dies 漏件式落料模porous mold 通气性模具 duplicated cavity plate 复板模?? positive mold 全压式模具 fantail die 扇尾形模具 pressure die 压紧模 fishtail die 鱼尾形模具?? profile die 轮廓模 flash mold 溢料式模具 progressive die 顺序模 gypsum mold 石膏铸模?? protable mold 手提式模具?? hot-runner mold 热流道模具?? prototype mold 雏形试验模具?? ingot mold 钢锭模
模具专业英语——注塑模
Injection Mold Technical Terms 特克内克腾目思 （一）模具专业基本用词 Professional Terms Intensification Factor 增强比 Scientific molding 科学注塑英腾次分克深发克偷 塞音特菲克计数器counter康特 Specific Injection Pressure (Psi)特殊注塑压力 思呗色服克 1．塑料—plastic, resin瑞申油管：Oil pipe 尼龙--------nylon 2．样件—sample 调节板-------adjust plate 3．钢料—steel A板--------a plate 4．注塑机—injection machine, press 定位圈----locating ring 喽客厅令 5．产品—part, product, moulding 斜导柱-----angular pin 安给拉PIN 6．模具—mold, mould, tool B板--------- b plate A 简易模（样板模）—prototype mold B 量产用模具—production mold 7．三维造型（数模）—3D model, 滚珠导套-------ball ejector bush 8．二维产品图—2D part drawing 拽应扁顶针--------blade ejector pin 布累得 9．设计—design 低赛应下模板--------bottom clamping plate 抱腾 10．制造—manufacture, 上模型腔------cavity main insert 11．检验—check, 上模镶件------cavity sub insert 12．测量—measure, 妹试司筒针--------center pin 深特 13．修改—change, modify 下模型芯------core main insert 14．工程更改—engineer change 下模镶针------core pin 15．质量—quality 快乐体下模镶件------core sub insert 16．数量—quantity 宽体踢延迟顶针-------delay ejector pin 17．基准—datum, reference 拉杆限位钉--------distance bolt （二）如何解析2D 产品图？How to read 2D part drawing? 一．产品几何Geometry 顶距限位柱--------distance spacer 1．点—point 销钉-------dowel pin 2．线（边）—line, edge 顶块--------ejector bar 3．面face 顶板导套-----ejector leader pin A 侧面—side塞得 B表面—surface射飞思 C 外观面—appearance surface安皮尔思射飞思4．壁厚—wall thickness 我射克来思顶板导柱----ejector leader pin李德拼 5．加强筋（骨位）—rib 瑞布顶针-------ejector pin 6．孔—hole后顶针地板------ejector plate 7．细长的槽—slot 顶针面板-----ejector retain plate 瑞腾 8．柱位—boss 抱死顶棍------ejector rod
注射模典型结构及分类
第五章注射模设计 塑料注射成所用的模具，称为注射成型模具，简称注射模或注塑模。 与其他塑料成型方法相比，注射成型塑件的内在和外观质量均较好，生产效率高，容易实现自动化，是应用最为广泛的塑料成型方法， 注射成型是热塑性塑料成型的一种重要方法，到目前为止除了氟塑料外，几乎所有的热塑性塑料都可用此方法成型。注射成型也已经成功应用于某些热固性塑料，甚至橡胶制品。 一、单分型面注射模的组成 按机构组成，单分型面注射模由模腔、成型零部件、浇注系统、导向机构、顶出装置、温度调节系统和结构零部件组成。 (1) 模腔 模具中用于成型塑料制件的空腔部分，由于模腔是直接成型塑料制件的部分，因此模腔的形状应朽塑件的形状一致，模腔一般由型腔、型芯组成。 (2) 成型零部件 构成塑料模具模腔的零件统称为成型零部件，通常包括型芯(成型塑件内部形状)、型腔(成型塑件外部形状)。 (3) 浇注系统
将塑料由注射机喷嘴引向型腔的流道称为浇注系统，浇注系统分主流道、分流道、浇口、冷料穴四个部分，是由浇口套、拉料杆和定模板上的流道组成。 (4) 导向机构 为确保动模与定模合模时准确对中而设导向零件。通常有导向柱、导向孔或在动模定模上分别设置互相吻合的内外锥面组成。 (5) 推出装置 在开模过程中，将塑件从模具中推出的装置。有的注射模具的推出装置为避免在顶出过程中推出板歪斜，还设有导向零件，使推板保持水平运动。由推杆、推板、推杆固定板、复位杆、主流道拉料杆、支承钉、推板导柱及推板导套组成。 (6) 温度调节和排气系统 为了满足注射工艺对模具温度的要求，模具设有冷却或加热系统，冷却系统一般在模具内开设冷却水道，冷却系统是由冷却水道和水嘴组成。加热则在模具内部或周围安装加热元件，如电加热元件。在注射成型过程中，为了将型腔内的气体排除模外，常常需要开设排气系统。 (7) 结构零部件 用来安装固定或支承成型零部件及前述的各部分机构的零部件。支承零部件组装在一起，可以构成注射模具的基本骨架。 二、单分型面注射模的工作原理 单分型面注射模的工作原理:模具合模时，在导柱和导套的导向定位下，动模和定模闭合。型腔由定模板上的型腔与固定在动模板上型芯组成，并由注射机合模系统提供的锁模力锁紧。然后注射机开始注射，塑料熔体经定模上的浇注系统进入型腔，带熔体充满型腔并经过保压、补塑和冷却定型后开模。开模时，注射机合模系统带动动模后退，模具从动模和定模分型面分开，塑件包在型芯上随动模一起后退，同时，拉料杆将浇注系统的主流道凝料从浇口套中拉出。当动模移动一定距离后，注射机的顶杆接触推板，推板机构开始动作，使推杆和拉料杆分别将塑件及浇注系统凝料从型芯和冷料穴中推出，塑件在浇注系统凝料一起从模具中落下，至此完成一次注射过程。合模时，推出机构靠复位杆复位并准备下一次注射。
注塑专业词汇翻译
成型工艺流程及条件介绍 Molding technique procedure and parameter introduction 第一節成型工艺Section 1 molding technique. 1.成型工艺参数类型 Sorts of molding parameter. (1). 注塑参数 Injection parameter. a.注射量 Injection rate. b.计量行程Screw back position c.余料量Cushion d.防诞量Sucking back rate e.螺杆转速Screw speed f.塑化量Plastic0 rate g.预塑背压Screw back pressure h.注射压力和保压压力Injection pressure and holding pressure i.注射速度Injection speed (2)合模参数Clamping parameter a.合模力Clamping force b.合模速度Clamping speed c.合模行程.Clamping stroke d.开模力Opening force e.开模速度Opening speed f.开模行程Opening position g.顶出压力Ejector advance pressure h.顶出速度Ejector advance speed i.顶出行程Ejector advance position 2.温控参数Temperature parameter a.烘料温度Dry resin material temperature b.料向与喷嘴温度Cylinder temperature and nozzle temperature c.模具温度Mold temperature d.油温Oil temperature 3.成型周期Molding cycle a.循环周期Cycle time b.冷却时间Cool time c.注射时间Injection time d.保压时间Holding pressure time e.塑化时间Plant time f.顶出及停留时间Knocking out and delay time g.低压保护时间Mold protect time 成型工艺参数的设定须根据产品的不同设置. Molding technique parameter setting differs depending on type of product 第二节成型条件设定Section 2 Molding parameter Setting
模具专业英文术语大全
实用文案 模具英语专业术语 模具述语开模槽：ply bar scot 内模管位：一、入水：gate core/cavity inter-lock 顶针：ejector pin 进入位：gate location 司筒：ejector sleeve 水口形式：gate type 司筒针：edge gate ejector pin 大水口：推板：细水口：stripper plate pin-point gate 缩呵：gate size movable core,return core core 水口大小：puller switching runner/gate 转水口：扣机（尼龙拉勾）：nylon latch lock sprue diameter 唧嘴口径：斜顶：lifter : runner 二、流道模胚（架）：mold base hot runner,hot manifold 热流道：上内模：cavity insert : hot sprue/cold runner 热嘴冷流道下内模：core insert : direct sprue gate 唧嘴直流行位（滑块）：slide round(full/half runner 圆形流道：镶件：insert mold flow analysis 流道电脑分析：压座/斜鸡：wedge :runner balance 流道平衡耐磨板/油板：wedge wear plate hot sprue 热嘴：压条：plate hot manifold 热流道板：撑头: support pillar cartridge heater 发热管：唧嘴：sprue bushing : thermocouples 探针挡板：stop plate connector plug 插头：定位圈：locating ring connector socket 插座：锁扣：latch seal 封料：/密封扣鸡：parting lock set water line 三、运水：推杆：push bar line lpug 喉塞：栓打螺丝：S.H.S.B tube 喉管：顶板：eracuretun plastic tube 塑胶管：活动臂：lever arm jiffy quick connector 快速接头：分流锥：spure sperader plug/socker 水口司mold components 四、模具零件：:bush 垃圾钉：三板模：3-plate mold stop pin 隔片：buffle 二板模：2-plate mold 弹弓柱：导边：/leader pin/guide pin spring rod 边钉弹弓:die spring 导套：边司/bushing/guide bushing 中托司：ejector guide bush 中托司：shoulder guide bushing 中托边：ejector guide pin guide pin ：L中托边镶针：ejector retainner plate 顶针板：pin 销子：托板：support plate dowel pin 波子弹弓：ball catch screw 螺丝：: pipe plug dowel pin 管钉：喉塞文案大全． 实用文案 锁模块：lock plate Mold repair 模具维修 angle from pin 斜顶：Molds 模具
专业英语-注塑成型专业词汇
专业英语---注塑成型专业词汇 Injection machine 啤机 Shot size（weight）实际射胶量injection volume 理论射胶量min mold height 最小容模厚度 Max mold height 最大容模厚度Tie bar clearance 拉杆间距Die plate size 模板尺寸 Ejector stroke 顶出行程barrel 炮筒，机筒clamp force 锁模力 non-return valve 止回阀 shear 剪切opening 开模行程Injection pressure 射胶压力back pressure 背压 nozzle size 射咀尺寸Cycle time 循环周期down time 停机时间hopper 料筒Mold release 脱模剂lubrication 润滑work horse 主力， 主要设备 Reserve pressure/packing pressure保压mold trial 试模shot （一）啤Decompress 减压oven 烤炉，烘灶shrinkage rate 收缩率Residence time 滞留时间 injection speed 注射速度booster time 增压时间Compression ratio 压缩 比 mold close time 合模时间 Resin 胶料 Plastification 塑化，增塑viscosity 粘性，粘度contamination 污染，杂 物 Thermoplastic 热塑性塑料thermosetting plastics 热固性塑料Booster time 增压时间 feed 喂料，填充purge 净化Flame retardant 阻燃degradation 降 解，软化
模具注塑术语中英文对照
根据国家规范，以下为部分塑料模具成形术语的规范翻译。 动模Movable Mould Moving Half 定模座板Fixed Clamp Plate Top Clamping Plate Top Plate 动模座板Moving Clamp Plate Bottom Clamping Plate Bottom Plate 上模座板Upper Clamping Plate 下模座板Lower Clamping Plate 凹模固定板Cavity-retainer Plate 型芯固定板Mould Core-retainer Plate 凸模固定板Punch-retainer Plate模套Die Body Die Sleeve Die Blank支承板Backing Plate Support Plate 垫块Spacer Parallel 支架Ejector Housing Mould Base Leg模头Die Head 模具分类8 Injection Mold 注塑模Plastic Rubber Mould 塑胶模Rubber Molding 橡胶成 形 Hot Chamber Die Casting 热室压铸Sand Mold Casting 砂模铸造 Extrusion Mold 挤出模Multi-Cavity Mold 多模穴模具 Palletizing Die 叠层模Plaster Mold 石膏 模Three Plates Mold 三板模Plain Die 简易模Pierce Die 冲孔模 Forming Die 成型模Progressive Die 连续模 Gang Dies 复合模Shearing Die 剪边模Cavity Die 型腔模 Riveting Die 铆合模Compression Molding 压缩成型Flash Mold 溢流式模具 Extrusion Mold 挤压式模具Split Mold 分割式模具Mould Cavity 型腔母模Mold Core 模芯公模Large Die Mold 大型模具Precise Die Mold 精密模具 Complex Die Mold 复杂模具Foaming Mould 发泡模具 Metal Die 金属模具Plastic Mold 塑料模具Tool Stamping Die Punch Die 冲压模具 Extrusion Die 挤压模具Graphite Die 石墨模具流道浇口部分Runner System 浇道系统Sprue Cold Material Trap 浇道冷料井Sprue Puller 拉杆 Runner Design 流道设计Main Runner 主流道 Secondary Runner 次流道Mould Gate Design 浇口设 计 Submarine Gate 潜伏浇口Tunnel Gate 隧道式浇口Pinpoint Gate 点浇口Fan Gate 扇形浇口 Side Gate 侧浇口Edge Gate 侧缘浇口 Tab Gate 搭接浇口Film Gate 薄膜浇口Flash Gate 闸门浇口Slit Gate 缝隙浇口 Dish Gate 盘形浇口Diaphragm Gate 隔膜浇口 Ring Gate 环形浇口Runnerless 无浇道 Sprueless 无射料管方式Long Nozzle 延长喷嘴方式 Sprue 浇口，溶渣Insulated/ Hot Runner 热浇 道Runner Plat 浇道模块Valve Gate阀门浇口Slag Well 冷料井Cold Slag 冷料渣 Sprue Gate 射料浇口Nozzle 射嘴 Sprue Lock Pin 料头钩销（拉料杆）注塑缺陷Flash 飞边Warpage 翘曲Air Trap 积风Blush 发赤Flow Line 流痕Splay 银纹Short Shot 短射Sink Mark 缩痕Streak 条纹Void 缩孔Weld Line 熔接线 Gas Mark 烧焦Cold Slug 冷斑Delamination 起皮Burr 毛刺Flaw Scratch 刮伤Gloss 光泽 Glazing 光滑Surface Check 表面裂痕Hesitation 迟滞注塑工艺Molding Conditions 成型条件Drying 烘干Barrel Temperature 料筒温度Melt Temperature 熔化温度 Mold Temperature 模具温度Injection Pressure 注塑压力Back Pressure 背压Injection Speed 注塑速度Screw Speed 螺杆转速Tensile Strength 抗拉强度T ensile Elongation 延伸率Flexural Modulus 弯曲模Flexural Strength 抗弯强度Shrinkage 收缩率Regrind Usage 次料使用Moulding 模塑机械设备 Lathe 车床Planer 刨床Miller / Milling Machine 铣床Grinder 磨床Driller 钻床Linear Cutting 线切割Electrical Sparkle 电火花Welder 电焊机Punching Machine 冲床Robot 机械手Common Equipment 常用设备EDM Electron Discharge Machining 放电加工3D Coordinate Measurement 三次元量床Boring Machine 搪孔机Contouring Machine 轮廓锯床Copy Grinding Machine 仿形磨床Cylindrical Grinding Machine 外圆磨床Die
注塑模具英文论文
Low Cost Injection Mold Creation via Hybrid Additive and Conventional Manufacturing 1. Introduction In most industrial applications, the manufacturing cost of a plastic part is mainly governed by the amount of material used in the molding process. Thus, current approaches for plastic part design and manufacturing focus primarily on establishing the minimum part thickness to reduce material usage. The assumption is that designing the mold and molding processes to the minimum thickness requirement should lead to the minimum manufacturing cost. Nowadays, electronic products such as mobile phones and medical devices are becoming ever more complex and their sizes are continually being reduced. The demand for small and thin plastic components for miniaturization assembly has considerably increased in recent years. Other factors besides minimal material usage may also become important when manufacturing thin plastic components. In particular, for thin parts, the injection molding pressure may become significant and has to be considered in the first phase of manufacturing. Employing current design approaches for plastic parts will fail to produce the true minimum manufacturing cost in these cases. Thus, tackling thin plastic parts requires a new approach, alongside existing mold design principles and molding techniques. 1.1 Current research Today, computer-aided simulation software is essential for the design of plastic parts and molds. Such software increases the efficiency of the design process by reducing the design cost and lead time [1]. Major systems, such as Mold Flow and C-Flow, use finite element analysis to simulate the filling phenomena, including flow patterns and filling sequences. Thus, the molding conditions can be predicted and validated, so that early design modifications can be achieved. Although available software is capable of analyzing the flow conditions, and the stress and the temperature distribution conditions of the component under various molding scenarios, they do not yield design parameters with minimum manufacturing cost [2,3]. The output data of the software only give parameter value ranges for reference and leaves the decision making to the component designer. Several attempts have also been made to optimize the parameters in feeding [4–7], cooling [2,8,9], and ejection These attempts were based on maximizing the flow ability of molten material during the molding process by using empirical relation ships between the product and mold design parameters.
模具专业术语
模具专业术语——注塑模(锦浩塑胶模具厂） English Training——Injection Mold （一）模具专业基本用词Professional Terms 1．塑料—plastic, resin 2．样件—sample 3．钢料—steel 4．注塑机—injection machine, press 5．产品—part, product, moulding 6．模具—mold, mould, tool A 简易模（样板模）—prototype mold B 量产用模具—production mold 7．三维造型（数模）—model, 3D data 8．二维产品图—2D part drawing 9．设计—design 10．制造—manufacture, build up, construction 11．检验—chec k, inspection 12．测量—measure, inspection 13．修改—change, modify, correction 14．工程更改—engineer change 15．质量—quality 16．数量—quantity 17．基准—datum, reference （二）如何解析2D 产品图？How to read 2D part drawing? 一．产品几何Geometry 1．点—point 2．线（边）—line, edge 3．面face A 侧面—side B 表面—surface C 外观面—appearance surface 4．壁厚—wall thickness, stock thickness 5．加强筋（骨位）—rib 6．孔—hole 7．细长的槽—slot 8．柱位—boss