TCM-Manager
TCM-Manager professional
TCM Manager professional There is one very important software for TCM-Controllers, it is called TCM Manager Be aware that there are two versions of this software:TCM-Manager. Be aware that there are two versions of this software:
The free version and the professional version. With free versions you could only
have a look at all memory locations, but with professional version you are able y p y to change memory locations and write the changes into the flash memory. This means that you can switch off the installation –after switching on again you will still have changes you made! Keep in mind that the EPROM has still the original memory settings. If someone is doing A6Ad the EPROM-values are loaded again p
loaded again.
s e n K r u p A company of ThyssenKrupp
Elevator
ThyssenKrupp Elevator (China)
T h y s
TCM-Manager professional
TCM Manager professional F001H =01 means this landing is only providing one main door.F001H is concerning to landing one.
F002H =D1 is showing us, that in landing two we have main door, switch off landing fireservice landing and parking landing switch off landing, fireservice landing and parking landing.F00BH =81 means that in landing 11 (=B,Hex) we have main door and parking landing. No fireservice landing and no switch off landing.
The same way it works from F050H to F09FH (main side) and F0A0H to F0EFH (l d th h)f di bl ll d ll f d fi t d p
(load through) for disable call and allowance of open door first. F050H and F0A0H is again the summary of what is provided and the next address F051H / F0A1H is
the first landing!
s e n K r u p g A company of ThyssenKrupp
Elevator
ThyssenKrupp Elevator (China)
T h y s
TCM-Manager professional
TCM Manager professional There are two memory locations you have to check in any case:this is the bottom most (lowest)landing F0F0H –this is the bottom-most (lowest) landing and
F0F1H –this is the top-most (highest) landing p (g )g They have to be set correctly!
Next memory locations you have to check are A470H and A4F0H . There you have to tell the controller in which sequence the MS-boards are connected.
p
s e n K r u p A company of ThyssenKrupp
Elevator
ThyssenKrupp Elevator (China)
T h y s
TCM-Manager professional
TCM Manager professional The example below shows us that in total there are 14 MS-boards connected =14)Furthermore we can see that the wire from the controller on line A (A470H =14). Furthermore we can see, that the wire from the controller on line A leads to landing 14H (20 dez). This means the lowest landing is the most distant
MS-board
MS board.If bit 7 equals to 1 it is load through.The maximum length is up to A4EFH p
.Line B is from
to s e n K r u p A4F0H to A55FH .
A company of ThyssenKrupp
Elevator
ThyssenKrupp Elevator (China)
T h y s
TCM-Manager professional
TCM Manager professional If you have problems collecting the calls have collecting the calls have a look at F0F2H which is type of the controller.yp Let ’s have a look at the correct setting on the next page.
p
s e n K r u p A company of ThyssenKrupp
Elevator
ThyssenKrupp Elevator (China)
T h y s
TCM-Manager professional
TCM Manager professional There are four different controller types you have to know:
PUBLIC TDST
TDST EQU 0F0F2H ;TDST=TYPE OF CONTROL
;TDST(0) = TYPE 510;TDST(1) = TYPE 511p
;()
;TDST(2) = TYPE 512;TDST(3) = TYPE 513;TDST(4) = RESERVED
;TDST(5) = GROUP(526 IF Bit 3=1 or 524 IF Bit 2=1);TDST(6)=TCI-CAN CONTROL s e n K r u p ;TDST(6) = TCI-CAN CONTROL
A company of ThyssenKrupp
Elevator
ThyssenKrupp Elevator (China)
T h y s
TCM-Manager professional
TCM Manager professional F0F2H =68H means
Bit(3)=1 –Type 513Bit(5)=1Group connected Bit(5)=1 –Group connected Bit(6)=1 –TCI/TCM-CAN Controller
Changing some memory location shows you the original and the changed value at the and the changed value at the column on the right side of TCM-Manager. Changes can p
be made on changing the hex,the dez value or by setting and s e n K r u p removing the marks.
A company of ThyssenKrupp
Elevator
ThyssenKrupp Elevator (China)
T h y s
TCM-Manager professional
TCM Manager professional The current version of TCM-Manager (13.01.2010) is the version 1.1.20?. After
starting the software you have to confirm that you are absolutely aware of what starting the software you have to confirm that you are absolutely aware of what you are doing.
p
s e n K r u p A company of ThyssenKrupp
Elevator
ThyssenKrupp Elevator (China)
T h y s
TCM-Manager professional
TCM Manager professional The following start screen start screen appears. Because of seeing no Marks you know that you haven ’t done any data p
any data Import.
s e n K r u p A company of ThyssenKrupp
Elevator
ThyssenKrupp Elevator (China)
T h y s
TCM-Manager professional
TCM Manager professional Therefore click on File and then if you are connected to any kind of TCM controller on Import If you are not connected but you want to open some saved HEX File on Import. If you are not connected but you want to open some saved HEX-File click on Open.
p
s e n K r u p A company of ThyssenKrupp
Elevator
ThyssenKrupp Elevator (China)
T h y s
TCM-Manager professional
TCM Manager professional After this it looks different. There appear some marks and you can see values at the memory locations the memory locations.
p
s e n K r u p A company of ThyssenKrupp
Elevator
ThyssenKrupp Elevator (China)
T h y s
TCM-Manager professional
TCM Manager professional Switching now to Hex-Input you can see single memory locations and sometimes a short description of them short description of them.
p
s e n K r u p A company of ThyssenKrupp
Elevator
ThyssenKrupp Elevator (China)
T h y s
TCM-Manager professional
TCM Manager professional Click there to change memory location
p
s e n K r u p A company of ThyssenKrupp
Elevator
ThyssenKrupp Elevator (China)
T h y s
TCM-Manager professional
TCM Manager professional To start looking at an elevator it at an elevator it is always a good idea to begin g with memory location F000H .You can find there what floor dependent data p
dependent data is provided.
s e n K r u p Furthermore you can see whether datatype “byte ”or “word ”is used.
A company of ThyssenKrupp
Elevator
ThyssenKrupp Elevator (China)
T h y s
TCM-Manager professional
TCM Manager professional On the left windows please click now on “Building specific data ”In the windows on the right side please click on Now the summary of all landings appears
the right side please click on F000H . Now the summary of all landings appears.This means that we can see now, that there is a parking landing at some level, g g there is a fireservice landing at some level, there is a switch off landing at some level and we have only main doors, no load through.
p
The memory locations from F0001H to F04FH are showing us the details of the related landing.
s e n K r u p A company of ThyssenKrupp
Elevator
ThyssenKrupp Elevator (China)
T h y s