1/12
March 2004s
HIGH SPEED:
f MAX =62MHz (TYP .)at V CC =6V s
LOW POWER DISSIPATION:I CC =4μA(MAX.)at T A =25°C s
HIGH NOISE IMMUNITY:
V NIH =V NIL =28%V CC (MIN.)
s
SYMMETRICAL OUTPUT IMPEDANCE:|I OH |=I OL =4mA (MIN)
s
BALANCED PROPAGATION DELAYS:t PLH ?t PHL
s
WIDE OPERATING VOLTAGE RANGE:V CC (OPR)=2V to 6V
s
PIN AND FUNCTION COMPATIBLE WITH 54SERIES 161
s SPACE GRADE-1:ESA SCC QUALIFIED s
50krad QUALIFIED,100krad AVAILABLE ON REQUEST
s
NO SEL UNDER HIGH LET HEAVY IONS IRRADIATION
s
DEVICE FULLY COMPLIANT WITH SCC-9204-059
DESCRIPTION
The M54HC161is an high speed CMOS SYNCHRONOUS 4-BIT BINARY PRESETTABLE COUNTER fabricated with silicon gate C 2MOS technology.
The CLOCK input is active on the rising edge.Both LOAD and CLEAR inputs are active LOW.Presetting is synchronous on the rising edge of the clock,the function is cleared asynchronously.Two enable inputs (TE and PE)and CARRY output are provided to enable easy cascading of counters,which facilities easy implementation of N-bit counters without using external gates.
All inputs are equipped with protection circuits against static discharge and transient excess voltage.
M54HC161
RAD-HARD SYNCHRONOUS PRESETTABLE 4-BIT
COUNTER
PIN CONNECTION
ORDER CODES
PACKAGE FM EM DILC M54HC161D M54HC161D1FPC
M54HC161K
M54HC161K1
M54HC161
2/12
IEC LOGIC SYMBOLS
INPUT AND OUTPUT EQUIVALENT CIRCUIT PIN DESCRIPTION
TRUTH TABLE
A,B,C,D :Logic level of data inputs Carry :CARRY =TE·Q A ·Q B ·Q C ·Q D
PIN N°SYMBOL NAME AND FUNCTION 1CLEAR Asynchronous Master Reset
2CLOCK Clock Input (LOW to HIGH,Edge-triggered)3,4,5,6
A,B,C,D
Data Inputs
7PE Count Enable Input
10TE Count Enable Carry Input 9
LOAD Parallel Enable Input 14,13,12,
11QA to QD Flip Flop Outputs 15CARRY Terminal Count Output 8
GND Ground (0V)
16
V CC
Positive Supply Voltage
M54HC161
3/12
LOGIC DIAGRAM
TIMING
CHART
M54HC161
4/12
ABSOLUTE MAXIMUM RATINGS
Absolute Maximum Ratings are those values beyond which damage to the device may occur.Functional operation under these conditions is not implied
RECOMMENDED OPERATING CONDITIONS
Symbol Parameter
Value Unit V CC Supply Voltage -0.5to +7V V I DC Input Voltage -0.5to V CC +0.5V V O DC Output Voltage -0.5to V CC +0.5
V I IK DC Input Diode Current ±20mA I OK DC Output Diode Current ±20mA I O DC Output Current ±25mA I CC or I GND DC V CC or Ground Current
±50mA P D Power Dissipation 300mW T stg Storage Temperature -65to +150
°C T L
Lead Temperature (10sec)
265
°C
Symbol Parameter
Value Unit V CC Supply Voltage 2to 6V V I Input Voltage 0to V CC V V O Output Voltage 0to V CC V T op Operating Temperature -55to 125°C t r ,t f
Input Rise and Fall Time
V CC =2.0V 0to 1000ns V CC =4.5V 0to 500ns V CC =6.0V
0to 400
ns
M54HC161
5/12
DC SPECIFICATIONS
Symbol
Parameter
Test Condition
Value Unit
V CC (V)T A =25°C -40to 85°C -55to 125°C Min.Typ.
Max.
Min.Max.
Min.Max.
V IH
High Level Input Voltage 2.0 1.5 1.5 1.5V 4.5 3.15 3.15 3.156.0 4.2
4.2
4.2
V IL
Low Level Input Voltage
2.00.50.50.5V
4.5 1.35 1.35 1.356.0 1.8
1.8
1.8V OH
High Level Output Voltage
2.0I O =-20μA 1.9 2.0 1.9 1.9V
4.5I O =-20μA 4.4 4.5 4.4 4.46.0I O =-20μA
5.9
6.0 5.9 5.94.5I O =-4.0mA 4.18 4.31 4.13 4.106.0
I O =-5.2mA 5.68
5.8 5.63
5.60
V OL
Low Level Output Voltage
2.0I O =20μA 0.00.10.10.1V 4.5I O =20μA 0.00.10.10.16.0I O =20μA 0.00.10.10.14.5I O =4.0mA 0.170.260.330.406.0
I O =5.2mA 0.18
0.260.330.40I I Input Leakage Current
6.0V I =V CC or GND ±0.1±1±1μA I CC
Quiescent Supply Current
6.0
V I =V CC or GND
4
40
80
μA
M54HC161
6/12
AC ELECTRICAL CHARACTERISTICS (C L =50pF,Input t r =t f =6ns)
Symbol
Parameter
Test Condition
Value Unit
V CC (V)T A =25°C -40to 85°C -55to 125°C Min.
Typ.Max.Min.
Max.Min.
Max.t TLH t THL Output Transition
Time 2.025*******ns 4.571519226.06131619t PLH t PHL Propagation Delay
Time
(CLOCK -Q)
2.048125155190ns
4.5162531386.014212632t PLH t PHL Propagation Delay
Time
(CLOCK -CARRY)
2.0571********ns
4.5193038456.016263238t PLH t PHL Propagation Delay
Time
(TE -CARRY)
2.0391********ns
4.5132025306.011172126t PLH
Propagation Delay Time (CLEAR -Q)
2.060150190225ns
4.5203038456.017263238t PHL
Propagation Delay Time
(CLEAR -CARRY)
2.0722********ns
4.5244050606.02034
43
51
f MAX
Maximum Clock Frequency 2.0 6.2185 4.2MHz
4.5315325216.037
6230
25
t W(H)t W(L)Minimum Pulse Width (CLOCK) 2.0187595110ns
4.561519226.06131619t W(L)
Minimum Pulse Width (CLEAR) 2.024*******ns
4.571519226.06131619t s
Minimum Set-up Time
(LOAD,PE,TE)
2.040100125150ns
4.5102025306.08172126t s
Minimum Set-up Time (A,B,C,D)
2.020*******ns
4.551519226.03
131619t h
Minimum Hold Time
(A,B -CLOCK)
2.0000ns
4.50006.0000t REM
Minimum Removal Time
2.018506575ns
4.541013156.0
3
9
11
13
M54HC161
7/12
CAPACITIVE CHARACTERISTICS
1)C PD is defined as the value of the IC’s internal equivalent capacitance which is calculated from the operating current consumption without load.(Refer to Test Circuit).Average operating current can be obtained by the following equation.I
CC(opr)=C PD x V CC x f IN +I CC
TEST CIRCUIT
L R T =Z OUT of pulse generator (typically 50?)
WAVEFORM 1:PROPAGATION DELAY TIMES,CLOCK MINIMUM PULSE WIDTH (f=1MHz;50%duty cycle)
Symbol
Parameter
Test Condition
Value Unit
V CC (V)T A =25°C -40to 85°C -55to 125°C Min.
Typ.Max.Min.
Max.Min.
Max.C IN Input Capacitance 5.0510
10
10
pF C PD
Power Dissipation Capacitance (note 1)
5.0
50
pF
M54HC161
8/12
WAVEFORM 2:PROPAGATION DELAY TIMES,CLEAR MINIMUM PULSE WIDTH (CLEAR MODE)(f=1MHz;50%duty cycle)
WAVEFORM 3:SETUP AND HOLD TIMES (PRESET MODE)(f=1MHz;50%duty
cycle)
M54HC161
9/12
WAVEFORM 4:SETUP AND HOLD TIMES (COUNTENABLE MODE)(f=1MHz;50%duty cycle)
WAVEFORM 5:PROPAGATION DELAY TIMES (CASCADE MODE)(f=1MHz;50%duty
cycle)
M54HC161
DILC-16 MECHANICAL DATA
mm.inch DIM.
MIN.TYP MAX.MIN.TYP.MAX.
A 2.1 2.710.0830.107
a1 3.00 3.700.1180.146 a20.630.88 1.140.0250.0350.045
B 1.82 2.390.0720.094
b0.400.450.500.0160.0180.020 b10.200.2540.300.0080.0100.012 D20.0620.3220.580.7900.8000.810 e7.367.627.870.2900.3000.310 e1 2.540.100
e217.6517.7817.900.6950.7000.705 e37.627.878.120.3000.3100.320 F7.297.497.700.2870.2950.303
I 3.830.151
K10.9012.10.4290.476 L 1.14 1.50.0450.059
0056437F
10/12
M54HC161
Information furnished is believed to be accurate and reliable. However, STMicroelectronics assumes no responsibility for the consequences of use of such information nor for any infringement of patents or other rights of third parties which may result from its use. No license is granted by implication or otherwise under any patent or patent rights of STMicroelectronics. Specifications mentioned in this publication are subject to change without notice. This publication supersedes and replaces all information previously supplied. STMicroelectronics products are not authorized for use as critical components in life support devices or systems without express written approval of STMicroelectronics.
The ST logo is a registered trademark of STMicroelectronics
All other names are the property of their respective owners
? 2004 STMicroelectronics - All Rights Reserved
STMicroelectronics GROUP OF COMPANIES
Australia - Belgium - Brazil - Canada - China - Czech Republic - Finland - France - Germany - Hong Kong - India - Israel - Italy - Japan - Malaysia - Malta - Morocco - Singapore - Spain - Sweden - Switzerland - United Kingdom - United States.
https://www.wendangku.net/doc/d714747412.html,
12/12